LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> GMC >> 2018 >> Acadia SL >> Repair and Diagnosis >> External Pages >> Different car >> Section 331 (Cellular System, Entertainment System, And Navigation System) >> Diagnostic Information and Procedures >> DTC B1025-B1135: Audio Output Circuits (UQF) >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

WARNING: This page is about a different car, the 2017 GMC Acadia. However, it is still accessible from the selected car via links, so may be relevant.

One Speaker

    NOTE:

    Some circuits supply audio signals to more than one speaker. It may be necessary to disconnect all speakers on the affected audio circuit when performing circuit tests.

  1. Ignition OFF, disconnect the harness connector at the appropriate P19 Speaker. Ignition ON, A11 Radio ON, mute OFF.
  2. Test for 5-7 V between each audio signal circuit terminal 1 and terminal 2 and ground.
    • If less than 5 V 
    1. Ignition OFF, disconnect the appropriate harness connector at the K108 Active Noise Cancellation Module / T3 Audio Amplifier.
    2. Test for infinite resistance between the appropriate signal circuits and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K108 Active Noise Cancellation Module / T3 Audio Amplifier.
    • If greater than 7 V 
    1. Ignition OFF, disconnect the appropriate harness connector at the K108 Active Noise Cancellation Module / T3 Audio Amplifier.
    2. Ignition ON, A11 Radio ON, mute OFF. Test for less than 1 V between the appropriate signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K108 Active Noise Cancellation Module / T3 Audio Amplifier.
    • If between 5-7 V 
  3. Ignition OFF, disconnect the appropriate harness connector at the K108 Active Noise Cancellation Module / T3 Audio Amplifier.
  4. Ignition ON, A11 Radio ON, mute OFF. Test for 5-7 V between each appropriate audio signal circuit from the A11 Radio and Ground.
    • If less than 5 V 
    1. Ignition OFF, Disconnect the appropriate speaker harness connector at the A11 Radio.
    2. Test for infinite resistance between the signal circuits and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the A11 Radio.
    • If greater than 7 V 
    1. Ignition OFF, disconnect the appropriate speaker harness connector at the A11 Radio. Ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the A11 Radio.
    • If between 5-7 V 
  5. Test or replace the P19 Speaker.

All Speakers

  1. Ignition OFF, disconnect the X1 harness connector at the K108 Active Noise Cancellation Module / T3 Audio Amplifier.
  2. Test for less than 10 Ω between the ground circuit terminal 8 and ground.
    • If 10 Ω or greater 
    1. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Verify that a test lamp illuminates between the B+ circuit terminal 4 and ground.
    • If the test lamp does not illuminate 
    1. Remove the test lamp.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
    • If the test lamp illuminates 
  4. Ignition ON, A11 Radio ON.
  5. Verify that a test lamp illuminates between the control circuit terminal 3 and ground.
    • If the test lamp does not illuminate 
    1. Ignition OFF, disconnect the X1 harness connector at the A11 Radio.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the A11 Radio.
    • If the test lamp illuminates 
  6. Test for 5-7 V between any audio signal circuit from the A11 Radio and Ground.
    • If not between 5-7 V 

      Test or replace the A11 Radio.

    • If between 5-7 V 
  7. Test or replace the K108 Active Noise Cancellation Module / T3 Audio Amplifier.
scientia non olet · About LEMON Manuals