(Digital Key System - Identity Authentication Unit (IAU) Removal And Installation)
Abbreviated Procedures
| Work | H/W | Tightening torque N.m (kgfm/lb-ft) | SST/Equipment | Chemical | etc | |
|---|---|---|---|---|---|---|
|
||||||
| 1 | Disconnect the battery negative (-) terminal | - | - | Diagnostic tool | - | |
| 2 | Remove the floor console mat | - | - | - | - | - |
| 3 | Remove the floor console upper cover assembly | Bolt | 7.8 - 11.8 (0.8 - 1.2/5.8 - 8.7) | - | - | - |
| Fastener | - | |||||
| 4 | Disconnect the floor console upper cover connector | - | - | - | - | - |
| 5 | Remove the floor console side cover [LH/RH] | Fastener | - | - | - | - |
| 6 | Remove the floor console assembly | Bolt | 7.8 - 11.8 (0.8 - 1.2/5.8 - 8.7) | - | - | - |
| 7 | Disconnect the floor console main connector | - | - | - | - | - |
| 8 | Remove the steering column shroud upper panel | Fastener | - | - | - | - |
| 9 | Remove the front door body side weather strip | - | - | - | - | - |
| 10 | Remove the crash pad side cover [RH] | Fastener | - | - | - | - |
| 11 | Open the glove box | - | - | - | - | - |
| 12 | Pull out the both sides stopper | - | - | - | - | - |
| 13 | Remove the lock pin and then remove the air damper | - | - | - | - | - |
| 14 | Remove the glove box lock pins | - | - | - | - | - |
| 15 | Remove the glove box | - | - | - | - | - |
| 16 | Remove the crash pad under cover [RH] | - | - | - | - | - |
| 17 | Disconnect the foot lamp connector | - | - | - | - | - |
| 18 | Remove the Heater & A/C Control Unit (DATC) | Fastener/Screw | - | - | - | - |
| 19 | Disconnect the Heater & A/C Control Unit (DATC) connectors | - | - | - | - | - |
| 20 | Remove the crash pad garnish [RH] | Fastener/Screw | - | - | - | - |
| 21 | Disconnect the Audio & AVN keyboard connector | - | - | - | - | - |
| 22 | Disconnect the mood lamp connector | - | - | - | - | - |
| 23 | Disconnect the SSB connector | - | - | - | - | - |
| 24 | Disconnect the incar sensor | - | - | - | - | - |
| 25 | Remove the audio & AVN head unit | Screw | - | - | - | - |
| 26 | Disconnect the audio & AVN head unit connectors | - | - | - | - | - |
| 27 | Remove the crash pad center panel [RH] | Nut | 7.8 - 11.8 (0.8 - 1.2/5.8 - 8.7) | - | - | - |
| Screw | - | - | - | - | ||
| 28 | Disconnect the crash pad center panel [RH] connectors | - | - | - | - | - |
| 29 | Remove the identity authentication unit | Nut | 6.9 - 9.8 (0.7 - 1.0/5.1 - 7.2) | - | - | - |
| 30 | Disconnect the identity authentication unit | - | - | - | - | - |
|
||||||
| Install in the reverse order of removal | ||||||
|
||||||
|
||||||