Specifications Index

COMMON SPECS & PROCEDURES INDEX

System		Specification/Procedure
Air Conditioning
Service		AIR CONDITIONING SERVICE SPECIFICATIONS
Torque		HEATING, VENTILATION, AND AIR CONDITIONING (2017 2018 2019) , HEATING, VENTILATION, AND AIR CONDITIONING (2020 2021 2022 2023)
Axle Nut/Hub Nut
Front 328 N.m (242 ft. lbs.) Rear 245 N.m (181 lbf.ft)
Battery		12 VOLT BATTERY REMOVAL, INSTALLATION, AND TEST (2017 2018 2019) , 12 VOLT BATTERY REMOVAL, INSTALLATION, AND TEST (2020 2021 2022 2023)
Brakes
Bleeding Sequence		CONVENTIONAL BRAKE SYSTEM BLEEDING
Disc Brakes		BRAKES SERVICE SPECIFICATIONS
Torque		BRAKES (2017 2018 2019) , BRAKES (2020 2021 2022 2023)
Charging
Service Specifications		ENGINE ELECTRICAL SERVICE SPECIFICATIONS
Torque		ENGINE ELECTRICAL (2017 2018 2019) , ENGINE ELECTRICAL (2020 2021 2022 2023)
Drive Belts
Belt Routing & Adjustment		DRIVE BELT REMOVAL, INSTALLATION, AND INSPECTION
Engine Cooling
General Service Specifications		COOLING SYSTEM SERVICE SPECIFICATIONS
Radiator Cap Pressure		93-123 kPa (0.95-1.25 kgf/cm2, 13.5-17.8 psi)
Thermostat R & I		THERMOSTAT REMOVAL, INSTALLATION, AND TEST (2017 2018 2019) , THERMOSTAT REMOVAL, INSTALLATION, AND TEST (2020 2021 2022 2023)
Water Pump R & I		WATER PASSAGE REMOVAL AND INSTALLATION (2017 2018 2019) , WATER PASSAGE REMOVAL AND INSTALLATION (2020 2021 2022 2023)
Engine Mechanical
Compression		930 kPa (9.48 kgf/cm² , 134.8 psi) Minimum 200 kPa (2.04 kgf/cm² , 29.0 psi) Maximum variation
Oil Pressure (176°F (80°C)		70 kPa (0.71 kgf/cm² , 10.1 psi) min. @ idle 490 kPa (5.00 kgf/cm² , 71.1 psi) min. @ 3000 RPM
Overhaul		See applicable specifications tables in ENGINE MECHANICAL SERVICE SPECIFICATIONS
Torque		ENGINE MECHANICAL (2017 2018 2019) , ENGINE MECHANICAL (2020 2021 2022 2023)
Fluid Specifications		See FLUIDS under MAINTENANCE tab.
Flywheel/Flex Plate Torque		74 N.m (55 ft. lbs.)
Fuel System
Pressure Specification		410 - 460 kPa (4.18 - 4.69 kgf/cm 2, 59.5 - 66.7 psi)
Fuel Pressure Test Procedure		FUEL PRESSURE TEST
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Spark Plug NGK: 7751
Gap		1.0-1.1 mm (0.039-0.043 in)
Torque		22 N.m (16 ft. lbs.)
Starting
Starter		ENGINE ELECTRICAL SERVICE SPECIFICATIONS
Torque		ENGINE ELECTRICAL (2017 2018 2019) , ENGINE ELECTRICAL (2020 2021 2022 2023)
Wheel Alignment
Adjustment Specifications		SUSPENSION SERVICE SPECIFICATIONS
	Torque	SUSPENSION (2017 2018 2019) , SUSPENSION (2020 2021 2022 2023)
Wheel & Tire
Wheel Lug Nut Torque		127 N.m (94 ft. lbs.)