Repair Procedures: Removal

Remove the following items;
1. Engine cover.
2. Air cleaner assembly and air duct.
3. Battery and battery tray.
Refer to REMOVAL .
Remove the ground line after removing the bolt (A).

Fig 1: Ground Line Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the solenoid valve connector (A) and inhibitor switch connector (B).

Fig 2: Solenoid Valve Connector And Inhibitor Switch Connector
Courtesy of HYUNDAI MOTOR AMERICA
Remove the control cable (C) after removing the nut (A) and the bolt (B).
Tightening torque:

(A) 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)

(B) 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)

Fig 3: Control Cable, Nut And Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

Fig 4: Hose And Automatic Transaxle Fluid Cooler Hose Clamps
Courtesy of HYUNDAI MOTOR AMERICA
Remove the wiring clips (A).

Fig 5: Wiring Clips
Courtesy of HYUNDAI MOTOR AMERICA
Remove the solenoid valve connector and inhibitor switch connector wiring mounting bracket (A).

Fig 6: Solenoid Valve Connector And Inhibitor Switch Connector Wiring Mounting Bracket Bolts
Courtesy of HYUNDAI MOTOR AMERICA
Using the engine support fixture (SST No.: 09200-38001), hold the engine and transaxle assembly safely.

Fig 7: Securing Engine And Transaxle Assembly Using Engine Support Fixture
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter motor mounting bolt (B-2ea).
Tightening torque:

(A, B) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

Fig 8: Automatic Transaxle Upper And Starter Motor Mounting Bolts
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle mounting support bracket bolt (A).
Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.8 lb-ft)

Fig 9: Automatic Transaxle Mounting Support Bracket Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Lift the vehicle with a jack.
Remove the under cover (A).
Tightening torque:

6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

Fig 10: Under Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the roll stopper (C) after removing the bolt (A) and (B).

Fig 11: Roll Stopper And Bolts
Courtesy of HYUNDAI MOTOR AMERICA
Remove the following items.
1. Drive shaft assembly.
  (Refer to REPLACEMENT .)
Remove the dust cover (A).

Fig 12: Dust Cover
Courtesy of HYUNDAI MOTOR AMERICA
Remove the torque converter mounting bolt (A-4ea) with rotating the crankshaft.
Tightening torque:

45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)

Fig 13: Torque Converter Mounting Bolt
Courtesy of HYUNDAI MOTOR AMERICA
Remove the automatic transaxle with a jack after removing the mounting bolt (A-2ea, B-3ea).
Tightening torque:

2013

(A) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

(B) 39.2 ~ 46.1 N.m (4.0 ~ 4.7 kgf.m, 28.9 ~ 34.0 lb-ft)

2014

(A) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

(B) 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

Fig 14: Automatic Transaxle Mounting Bolts
Courtesy of HYUNDAI MOTOR AMERICA