LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2007 >> M35 Base >> Repair and Diagnosis >> Body & Frame >> Door Locks >> Body, Lock & Security System >> Intelligent Key System >> Check Park Position Switch
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Check Park Position Switch

  1. CHECK PARK POSITION SWITCH INPUT SIGNAL 

    With CONSULT-II 

    Check ("P RANGE SW") in "DATA MONITOR" mode.

    DATA MONITOR

    Monitor item Condition
    P RANGE SW A/T device P position: ON
    Other than above: OFF
    Fig 1: CONSULT-II Display - Data Monitor
    G05212255

    Without CONSULT-II 

    1. Turn ignition switch OFF.
    2. Check voltage between Intelligent Key unit connector and ground.
      TERMINAL VOLTAGE CHART

      Terminals A/T device position Voltage (V) (Approx.)
      (+) (-)
      Intelligent Key unit connector Terminal
      M32 27 Ground P 0
      Other than above Battery voltage
      Fig 2: Checking Voltage Between Intelligent Key Unit Connector Terminal 27 And Ground
      G05212256

    OK or NG 

    OK: Park position switch circuit is OK.

    NG: GO TO 2.

  2. CHECK INTELLIGENT KEY UNIT OUTPUT SIGNAL 

    Check voltage between Intelligent Key unit connector and ground.

    TERMINAL VOLTAGE CHART

    Terminals Condition Voltage (V) (Approx.)
    (+) (-)
    Intelligent Key unit connector Terminal
    M33 58 Ground Wake-up state (Open drive side door) Battery voltage
    Sleep state (After 30 seconds or more since all doors are closed under the condition that the ignition switch is in the LOCK position) 0
    Fig 3: Checking Voltage Between Intelligent Key Unit Connector Terminal 58 And Ground
    G05212257

    OK or NG 

    OK: GO TO 3.

    NG: Check the condition of harness and connector.

  3. CHECK PARK POSITION SWITCH 
    1. Disconnect A/T device connector.
    2. Check A/T device.
      TERMINAL REFERENCE CHART

      Terminal A/T device position Continuity
      A/T device
      9 10 P Yes
      Other than above No

    OK or NG 

    OK: GO TO 4.

    NG: Check A/T shift lock system. Refer to "A/T SHIFT LOCK SYSTEM ".

    Fig 4: Checking Park Position Switch
    G05212258
  4. CHECK HARNESS CONTINUITY 1 
    1. Disconnect A/T device connector.
    2. Check continuity between Intelligent Key unit connector and A/T device connector.
      TERMINAL CONTINUITY CHART

      A B Continuity
      Intelligent Key unit connector Terminal A/T device connector Terminal
      M32 27 M133 10 Yes
    3. Check continuity between Intelligent Key unit connector and ground.
      TERMINAL CONTINUITY CHART

      A Ground Continuity
      Intelligent Key unit connector Terminal
      M32 27 No
      Fig 5: Checking Continuity Between Intelligent Key Unit Connector And A/T Device Connector
      G05212259

    OK or NG 

    OK: GO TO 5.

    NG: Repair or replace harness between Intelligent Key and A/T device.

  5. CHECK HARNESS CONTINUITY 2 
    1. Check continuity between Intelligent Key unit connector and A/T device connector.
      TERMINAL CONTINUITY CHART

      A B Continuity
      Intelligent Key unit connector Terminal A/T device connector Terminal
      M33 58 M133 9 Yes
    2. Check continuity between Intelligent Key unit connector and ground.
      TERMINAL CONTINUITY CHART

      A Ground Continuity
      Intelligent Key unit connector Terminal
      M33 58 No
      Fig 6: Checking Continuity Between Intelligent Key Unit Connector And A/T Device Connector
      G05212260

    OK or NG 

    OK: Check the condition of harness and connector.

    NG: Repair or replace harness between Intelligent Key and A/T device.

scientia non olet · About LEMON Manuals