LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2008 >> G37 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 45 (Brake Control System (Abs)) >> Ecu Diagnosis >> Abs Actuator And Electric Unit (Control Unit) >> Reference Value >> Values On The Diagnosis Tool
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Values On The Diagnosis Tool

WARNING: This page is about a different car, the 2008 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short-circuited.
ABS ACTUATOR AND ELECTRIC UNIT REFERENCE VALUE CHART

CONSULT-III MONITOR ITEM
Monitor item Display content Data monitor
Condition Reference value in normal operation
FR LH SENSOR Wheel speed 0 [km/h (MPH)] Vehicle stopped
Nearly matches the speed meter display (± 10% or less) Vehicle running (Note 1)
FR RH SENSOR Wheel speed 0 [km/h (MPH)] Vehicle stopped
Nearly matches the speed meter display (± 10% or less) Vehicle running (Note 1)
RR LH SENSOR Wheel speed 0 [km/h (MPH)] Vehicle stopped
Nearly matches the speed meter display (± 10% or less) Vehicle running (Note 1)
RR RH SENSOR Wheel speed 0 [km/h (MPH)] Vehicle stopped
Nearly matches the speed meter display (± 10% or less) Vehicle running (Note 1)
STOP LAMP SW Stop lamp switch signal status When brake pedal is depressed ON
When brake pedal is released OFF
BATTERY VOLT Battery voltage supplied to the ABS actuator and electric unit (control unit) Ignition switch ON 10 - 16 V
FR RH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) ON
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) OFF
FR RH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) ON
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) OFF
FR LH IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) ON
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) OFF
FR LH OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) ON
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) OFF
REAR IN SOL Operation status of each solenoid valve Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) ON
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) OFF
REAR OUT SOL Operation status of each solenoid valve Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-III) or actuator relay is inactive (in fail-safe mode) ON
When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) OFF
MOTOR RELAY Motor and motor relay operation When the motor relay and motor are operating ON
When the motor relay and motor are not operating OFF
ACTUATOR RLY Actuator relay operation When the actuator relay is operating ON
When the actuator relay is not operating OFF
ABS WARN LAMP ABS warning lamp (Note 2) When ABS warning lamp is ON ON
When ABS warning lamp is OFF OFF
EBD SIGNAL EBD operation EBD is active ON
EBD is inactive OFF
ABS SIGNAL ABS operation ABS is active ON
ABS is inactive OFF
EBD FAIL SIG EBD fail-safe signal In EBD fail-safe ON
EBD is normal OFF
ABS FAIL SIG ABS fail-safe signal In ABS fail-safe ON
ABS is normal OFF
NOTE:
  • 1: Confirm tire pressure is normal.
  • 2: On and off timing for warning lamp and indicator lamp. Refer to , "DESCRIPTION ".