LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2009 >> M45 Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Body, Lock & Security System >> Service Information >> Intelligent Key System/Engine Start Function >> DTC B2558: Shift Position >> Diagnostic Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedure

  1. CHECK CONTROL DEVICE SIGNAL
    1. Turn ignition switch ON.
    2. Check voltage between Intelligent Key unit connector and ground.
    VOLTAGE REFERENCE CHART

    Terminals A/T control device position Voltage (V) (Approx.)
    (+) (-)
    Intelligent Key unit connector Terminal
    M32 27 Ground P 0
    Other than above Battery voltage
    Fig 1: Checking Voltage Between Intelligent Key Unit Connector And Ground
    G05212339Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO  4.

    NG: GO TO  2.

  2. CHECK HARNESS CONTINUITY 1
    1. Turn ignition switch OFF.
    2. Disconnect Intelligent Key unit and control device connector.
    3. Check continuity between Intelligent Key unit connector and control device connector.
      CONTINUITY REFERENCE CHART

      A B Continuity
      Intelligent Key unit connector Terminal Control device connector Terminal
      M32 27 M133 10 Yes
      M33 58 9
    4. Check continuity between Intelligent Key unit connector and ground.
    CONTINUITY REFERENCE CHART

    A Ground Continuity
    Intelligent Key unit connector Terminal
    M32 27 No
    M33 58
    Fig 2: Checking Continuity Between Intelligent Key Unit And Control Device Connector
    G05212340Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO  3.

    NG: Repair or replace harness.

  3. CHECK CONTROL DEVICE

    Check control device.

    CONTINUITY REFERENCE CHART

    Terminal A/T control device position Continuity
    Control device
    9 10 P Yes
    Other than above No

    OK or NG 

    OK: Check the condition of harness and connector. If it is OK, check the self-diagnosis results using CONSULT-III again.

    NG: Replace control device.

    Fig 3: Checking Control Device
    G05212341Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK TCM SIGNAL

    Check Intelligent Key unit connector and ground.

    VOLTAGE REFERENCE CHART

    Terminals A/T control device position Voltage (V) (Approx.)
    (+) (-)
    Intelligent Key unit connector Terminal
    M32 28 Ground N or P Battery voltage
    Other than above 0
    Fig 4: Checking Intelligent Key Unit Connector And Ground
    G05212342Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Check the condition of harness and connector. If it is OK, check the self-diagnosis results using CONSULT-III again.

    NG: GO TO  5.

  5. CHECK HARNESS CONTINUITY 2
    1. Turn ignition switch OFF.
    2. Disconnect Intelligent Key unit and TCM connector.
    3. Check continuity between Intelligent Key unit connector and TCM connector.
      CONTINUITY REFERENCE CHART

      A B Continuity
      Intelligent Key unit connector Terminal TCM connector Terminal
      M32 28 F502 8 Yes
    4. Check continuity between Intelligent Key unit connector and ground.
    CONTINUITY REFERENCE CHART

    A Ground Continuity
    Intelligent Key unit connector Terminal
    M32 28 No
    Fig 5: Checking Continuity Between Intelligent Key Unit And TCM Connector
    G05212343Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Replace TCM.

    NG: Repair or replace harness.

scientia non olet · About LEMON Manuals