LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2010 >> G37 Base, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 265 (Security Control System) >> With Intelligent Key System >> DTC/Circuit Diagnosis >> DTC B2620: Park/Neutral Position Switch >> Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis Procedure

WARNING: This page is about a different car, the 2011 Nissan Juke. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC OF COMBINATION METER

    Check DTC in "Self Diagnostic Result" mode of "METER/M&A" using CONSULT-III.

    Refer to "DTC INDEX ".

    Is the inspection result normal? 

    YES: GO TO 2.

    NO: Repair or replace the malfunctioning parts.

  2. CHECK FUSE
    1. Turn power switch OFF.
    2. Check that the following fuse in the fuse block (J/B) is not blown.
      FUSE REFERENCE CHART

      Signal name Fuse No.
      Ignition power supply 5 (10 A)

      Is the inspection result normal? 

      YES: GO TO 3.

      NO: Replace the blown fuse after repairing the cause of blowing.

  3. CHECK PARK/NEUTRAL POSITION SWITCH POWER SUPPLY
    1. Turn ignition switch OFF.
    2. Disconnect park/neutral position switch connector.
    3. Turn ignition switch ON.
    4. Check voltage between park/neutral position switch harness connector and ground.
      CONNECTOR TERMINALS VOLTAGE REFERENCE CHART

      (+) (-) Voltage (V) (Approx.)
      Park/neutral position switch
      Connector Terminal
      F49 2 Ground Battery voltage

      Is the inspection result normal? 

      YES: GO TO 4.

      NO: Repair or replace harness.

  4. CHECK PARK/NEUTRAL POSITION SWITCH INPUT SIGNAL
    1. Turn ignition switch OFF.
    2. Connect park/neutral position switch connector.
    3. Turn ignition switch ON.
    4. Check voltage between BCM harness connector and ground.
      CONNECTOR TERMINALS VOLTAGE REFERENCE CHART

      (+) (-) Condition Voltage (V) (Approx.)
      BCM
      Connector Terminal
      M70 102 Ground Shift lever Neutral position Battery voltage
      Except neutral position 0

      Is the inspection result normal? 

      YES: GO TO 5.

      NO: GO TO  6.

  5. REPLACE BCM
    1. Replace BCM. Refer to "REMOVAL AND INSTALLATION ".
    2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT-III.

      For initialization and registration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.

      INSPECTION END

  6. CHECK PARK/NEUTRAL POSITION SWITCH SIGNAL CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect park/neutral position switch connector.
    3. Disconnect BCM connector.
    4. Check continuity between park/neutral position switch harness connector and BCM harness connector.
      CONNECTOR TERMINALS CONTINUITY REFERENCE CHART

      Park/neutral position switch BCM Continuity
      Connector Terminal Connector Terminal
      F49 3 M70 102 Existed

      Is the inspection result normal? 

      YES: GO TO 7.

      NO: Repair or replace harness.

  7. CHECK PARK/NEUTRAL POSITION SWITCH

    Refer to , "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO 8.

    NO: Replace park/neutral position switch. Refer to "REMOVAL AND INSTALLATION ".

  8. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    INSPECTION END

scientia non olet · About LEMON Manuals