LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2012 >> G37 Base, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 190 (Power Control System) >> Power Distribution System >> System Description >> Diagnosis System (BCM) >> Intelligent Key >> INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)

WARNING: This page is about a different car, the 2011 Nissan 370Z. However, it is still accessible from the selected car via links, so may be relevant.

WORK SUPPORT

MONITOR ITEM DESCRIPTION

Monitor item Description
CONFIRM KEY FOB ID It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET Auto door lock time can be changed in this mode
  • MODE 1: 1 minute
  • MODE 2: 5 minutes
  • MODE 3: 30 seconds
  • MODE 4: 2 minutes
LOCK/UNLOCK BY I-KEY Door lock/unlock function by door request switch (driver side, passenger side and back door side/trunk lid(1)) mode can be changed to operate (On) or not operate (Off) in this mode
ENGINE START BY I-KEY Engine start function mode can be changed to operate (On) or not operate (Off) with this mode
TRUNK/GLASS HATCH OPEN Buzzer reminder function mode by back door opener switch/trunk lid opener switch(1) can be changed to operate (ON) or not operate (OFF) with this mode
PANIC ALARM SET Panic alarm button pressing time on Intelligent Key remote control button can be selected from the following with this mode
  • MODE 1: 0.5 sec.
  • MODE 2: Non-operation
  • MODE 3: 1.5 sec.
TAKE OUT FROM WIN WARN
NOTE: This item is displayed, but cannot be monitored
PW DOWN SET Unlock button pressing time on Intelligent Key button can be selected from the following with this mode
  • MODE 1: 3 sec.
  • MODE 2: Non-operation
  • MODE 3: 5 sec.
TRUNK OPEN DELAY
NOTE: This item is displayed, but cannot be supported
LO-BATT OF KEY FOB WARN Intelligent Key low battery warning mode can be changed to operate (On) or not operate (Off) with this mode
ANTI KEY LOCK IN FUNCTI Key reminder function mode can be changed to operate (On) or not operate (Off) with this mode
HAZARD ANSWER BACK Hazard reminder function mode can be selected from the following with this mode
  • LOCK ONLY: Door lock operation only
  • UNLOCK ONLY: Door unlock operation only
  • LOCK/UNLOCK: Lock/unlock operation
  • OFF: Non-operation
ANS BACK I-KEY LOCK Buzzer reminder function (lock operation) mode by door request switch (driver side, passenger side and back door side/trunk lid(1)) can be selected from the following with this mode
  • Horn chirp: Sound horn
  • Buzzer: Sound Intelligent Key warning buzzer
  • OFF: Non-operation
ANS BACK I-KEY UNLOCK Buzzer reminder function (unlock operation) mode by door request switch (driver side, passenger side and back door side/trunk lid(1)) can be changed to operate (On) or not operate (Off) with this mode
SHORT CRANKING OUTPUT Starter motor can be forcibly activated
INSIDE ANT DIAGNOSIS This function allows inside key antenna self-diagnosis
HORN WITH KEYLESS LOCK Horn reminder function mode by Intelligent Key button can be changed to operate (On) or not operate (Off) with this mode
(1) For roadster models

SELF-DIAG RESULT

Refer to "DTC INDEX ".

DATA MONITOR

MONITOR ITEM CONDITION

Monitor Item Condition
REQ SW-DR Indicates [On/Off] condition of driver side door request switch
REQ SW-AS Indicates [On/Off] condition of passenger side door request switch
REQ SW-BD/TR Indicates [On/Off] condition of back door request switch/trunk lid door request switch(4)
PUSH SW Indicates [On/Off] condition of push-button ignition switch
IGN RLY2 -F/B Indicates [On/Off] condition of ignition relay 2
ACC RLY-F/B
NOTE: This item is displayed, but cannot be monitored
CLUCH SW(1) Indicates [On/Off] condition of clutch switch
BRAKE SW 1 Indicates [On/Off](3) condition of brake switch power supply
BRAKE SW 2 Indicates [On/Off] condition of brake switch
DETE/CANCL SW(2) Indicates [On/Off] condition of P position
SFT PN/N SW(2) Indicates [On/Off] condition of P or N position
S/L-LOCK Indicates [On/Off] condition of steering lock unit (LOCK)
NOTE: For models without steering lock unit, this item is not monitored.
S/L-UNLOCK Indicates [On/Off] condition of steering lock unit (UNLOCK)
NOTE: For models without steering lock unit, this item is not monitored.
S/L RELAY-F/B Indicates [On/Off] condition of steering lock relay
NOTE: For models without steering lock unit, this item is not monitored.
UNLK SEN-DR Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW-IPDM Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B Indicates [On/Off] condition of ignition relay 1
DETE SW-IPDM(2) Indicates [On/Off] condition of P position
SFT PN-IPDM(2) Indicates [On/Off] condition of P or N position
SFT P-MET(2) Indicates [On/Off] condition of P position
SFT N-MET(2) Indicates [On/Off] condition of N position
ENGINE STATE Indicates [STOP/STALL/CRANK/RUN] condition of engine states
S/L LOCK-IPDM Indicates [On/Off] condition of steering lock unit (LOCK)
NOTE: For models without steering lock unit, this item is not monitored.
S/L UNLK-IPDM Indicates [On/Off] condition of steering lock unit (UNLOCK)
NOTE: For models without steering lock unit, this item is not monitored.
S/L RELAY-REQ Indicates [On/Off] condition of steering lock relay
NOTE: For models without steering lock unit, this item is not monitored.
VEH SPEED 1 Display the vehicle speed signal received from combination meter by numerical value [km/h]
VEH SPEED 2 Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [km/h]
DOOR STAT-DR Indicates [LOCK/READY/UNLOCK] condition of driver side door status
DOOR STAT-AS Indicates [LOCK/READY/UNLOCK] condition of passenger side door status
ID OK FLAG Indicates [Set/Reset] condition of key ID
PRMT ENG STRT Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE: This item is displayed, but cannot be monitored
KEY SW-SLOT Indicates [On/Off] condition of key slot
TRNK/HAT MNTR
NOTE: This item is displayed, but cannot be monitored
RKE-LOCK Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE: This item is displayed, but cannot be monitored
RKE-PANIC Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-P/W OPEN Indicates [On/Off] condition of P/W DOWN signal from Intelligent Key
RKE-MODE CHG Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1 When remote keyless entry receiver (front) receives the signal transmitted while operating on Intelligent Key, the numerical value start changing
RKE OPE COUN2
NOTE: This item is displayed, but cannot be monitored
REVERSE SW(1) Indicates [On/Off] condition of R position
(1) It is displayed but does not operate on A/T models.
(2) It is displayed but does not operate on M/T models.
(3) OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
(4) For roadster models

ACTIVE TEST

TEST ITEM DESCRIPTION

Test item Description
BATTERY SAVER This test is able to check interior room lamp operation
The interior room lamp is activated after "On" on CONSULT-III screen is touched
PW REMOTO DOWN SET This test is able to check power window down operation
The power window down is activated after "On" on CONSULT-III screen is touched
OUTSIDE BUZZER This test is able to check Intelligent Key warning buzzer operation
The Intelligent Key warning buzzer is activated after "On" on CONSULT-III screen is touched
INSIDE BUZZER This test is able to check warning chime in combination meter operation
  • Take away warning chime sounds when "Take out" on CONSULT-III screen is touched
  • Key warning chime sounds when "Key" on CONSULT-III screen is touched
  • OFF position warning chime sounds when "Knob" on CONSULT-III screen is touched
INDICATOR This test is able to check warning lamp operation
  • "KEY" Warning lamp illuminates when "Key on" on CONSULT-III screen is touched
  • "KEY" Warning lamp blinks when "Key ind" on CONSULT-III screen is touched
INT LAMP This test is able to check interior room lamp operation
The interior room lamp is activated after "On" on CONSULT-III screen is touched
LCD This test is able to check meter display information
  • Engine start information displays when "BP N" on CONSULT-III screen is touched
  • Engine start information displays when "BP I" on CONSULT-III screen is touched
  • Key ID warning displays when "ID NG" on CONSULT-III screen is touched
  • Steering lock information displays when "ROTAT" on CONSULT-III screen is touched
    NOTE: For models without steering lock unit, "ROTAT" is displayed but cannot be tested.
  • P position warning displays when "SFT P" on CONSULT-III screen is touched
  • Intelligent Key insert information displays when "INSRT" on CONSULT-III screen is touched
  • Intelligent Key low battery warning displays when "BATT" on CONSULT-III screen is touched
  • Take away through window warning displays when "NO KY" on CONSULT-III screen is touched
  • Take away warning display when "OUTKEY" on CONSULT-III screen is touched
  • OFF position warning display when "LK WN" on CONSULT-III screen is touched
TRUNK/GLASS HATCH
NOTE: This item is displayed, but cannot be tested
FLASHER This test is able to check hazard warning lamp operation
The hazard warning lamps are activated after "LH/RH/Off" on CONSULT-III screen is touched
HORN This test is able to check horn operation
The horn is activated after "On" on CONSULT-III screen is touched
P RANGE(1) This test is able to check A/T shift selector power supply
A/T shift selector power is supplied when "On" on CONSULT-III screen is touched
ENGINE SW ILLUMI This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when "On" on CONSULT-III screen is touched
LOCK INDICATOR This test is able to check LOCK indicator in push-ignition switch operation LOCK indicator in push-ignition switch illuminates when "On" on CONSULT-III screen is touched
ACC INDICATOR This test is able to check ACC indicator in push-ignition switch operation
ACC indicator in push-ignition switch illuminates when "On" on CONSULT-III screen is touched
IGNITION ON IND This test is able to check ON indicator in push-ignition switch operation
ON indicator in push-ignition switch illuminates when "On" on CONSULT-III screen is touched
KEY SLOT ILLUMI This test is able to check key slot illumination operation
Key slot illumination blinks when "On" on CONSULT-III screen is touched
TRUNK/BACK DOOR This test is able to check back door opener actuator/trunk lid opener actuator(2) open operation
This actuator opens when "Open" on CONSULT-III screen is touched
(1) It is displayed but does not operate on M/T models.
(2) For roadster models


WORK SUPPORT

MONITOR ITEM DESCRIPTION

Monitor item Description
CONFIRM KEY FOB ID It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET Auto door lock time can be changed in this mode
  • MODE 1: 1 minute
  • MODE 2: 5 minutes
  • MODE 3: 30 seconds
  • MODE 4: 2 minutes
LOCK/UNLOCK BY I-KEY Door lock/unlock function by door request switch (driver side, passenger side and back door side/trunk lid(1)) mode can be changed to operate (On) or not operate (Off) in this mode
ENGINE START BY I-KEY Engine start function mode can be changed to operate (On) or not operate (Off) with this mode
TRUNK/GLASS HATCH OPEN Buzzer reminder function mode by back door opener switch/trunk lid opener switch(1) can be changed to operate (ON) or not operate (OFF) with this mode
PANIC ALARM SET Panic alarm button pressing time on Intelligent Key remote control button can be selected from the following with this mode
  • MODE 1: 0.5 sec.
  • MODE 2: Non-operation
  • MODE 3: 1.5 sec.
TAKE OUT FROM WIN WARN
NOTE: This item is displayed, but cannot be monitored
PW DOWN SET Unlock button pressing time on Intelligent Key button can be selected from the following with this mode
  • MODE 1: 3 sec.
  • MODE 2: Non-operation
  • MODE 3: 5 sec.
TRUNK OPEN DELAY
NOTE: This item is displayed, but cannot be supported
LO-BATT OF KEY FOB WARN Intelligent Key low battery warning mode can be changed to operate (On) or not operate (Off) with this mode
ANTI KEY LOCK IN FUNCTI Key reminder function mode can be changed to operate (On) or not operate (Off) with this mode
HAZARD ANSWER BACK Hazard reminder function mode can be selected from the following with this mode
  • LOCK ONLY: Door lock operation only
  • UNLOCK ONLY: Door unlock operation only
  • LOCK/UNLOCK: Lock/unlock operation
  • OFF: Non-operation
ANS BACK I-KEY LOCK Buzzer reminder function (lock operation) mode by door request switch (driver side, passenger side and back door side/trunk lid(1)) can be selected from the following with this mode
  • Horn chirp: Sound horn
  • Buzzer: Sound Intelligent Key warning buzzer
  • OFF: Non-operation
ANS BACK I-KEY UNLOCK Buzzer reminder function (unlock operation) mode by door request switch (driver side, passenger side and back door side/trunk lid(1)) can be changed to operate (On) or not operate (Off) with this mode
SHORT CRANKING OUTPUT Starter motor can be forcibly activated
INSIDE ANT DIAGNOSIS This function allows inside key antenna self-diagnosis
HORN WITH KEYLESS LOCK Horn reminder function mode by Intelligent Key button can be changed to operate (On) or not operate (Off) with this mode
(1) For roadster models

SELF-DIAG RESULT

Refer to "DTC INDEX ".

DATA MONITOR

MONITOR ITEM CONDITION

Monitor Item Condition
REQ SW-DR Indicates [On/Off] condition of driver side door request switch
REQ SW-AS Indicates [On/Off] condition of passenger side door request switch
REQ SW-BD/TR Indicates [On/Off] condition of back door request switch/trunk lid door request switch(4)
PUSH SW Indicates [On/Off] condition of push-button ignition switch
IGN RLY2 -F/B Indicates [On/Off] condition of ignition relay 2
ACC RLY-F/B
NOTE: This item is displayed, but cannot be monitored
CLUCH SW(1) Indicates [On/Off] condition of clutch switch
BRAKE SW 1 Indicates [On/Off](3) condition of brake switch power supply
BRAKE SW 2 Indicates [On/Off] condition of brake switch
DETE/CANCL SW(2) Indicates [On/Off] condition of P position
SFT PN/N SW(2) Indicates [On/Off] condition of P or N position
S/L-LOCK Indicates [On/Off] condition of steering lock unit (LOCK)
NOTE: For models without steering look unit, this item is not monitored.
S/L-UNLOCK Indicates [On/Off] condition of steering lock unit (UNLOCK)
NOTE: For models without steering look unit, this item is not monitored.
S/L RELAY-F/B Indicates [On/Off] condition of steering lock relay
NOTE: For models without steering look unit, this item is not monitored.
UNLK SEN-DR Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW-IPDM Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B Indicates [On/Off] condition of ignition relay 1
DETE SW-IPDM(2) Indicates [On/Off] condition of P position
SFT PN-IPDM(2) Indicates [On/Off] condition of P or N position
SFT P-MET(2) Indicates [On/Off] condition of P position
SFT N-MET(2) Indicates [On/Off] condition of N position
ENGINE STATE Indicates [STOP/STALL/CRANK/RUN] condition of engine states
S/L LOCK-IPDM Indicates [On/Off] condition of steering lock unit (LOCK)
NOTE: For models without steering look unit, this item is not monitored.
S/L UNLK-IPDM Indicates [On/Off] condition of steering lock unit (UNLOCK)
NOTE: For models without steering look unit, this item is not monitored.
S/L RELAY-REQ Indicates [On/Off] condition of steering lock relay
NOTE: For models without steering look unit, this item is not monitored.
VEH SPEED 1 Display the vehicle speed signal received from combination meter by numerical value [km/h]
VEH SPEED 2 Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [km/h]
DOOR STAT-DR Indicates [LOCK/READY/UNLOCK] condition of driver side door status
DOOR STAT-AS Indicates [LOCK/READY/UNLOCK] condition of passenger side door status
ID OK FLAG Indicates [Set/Reset] condition of key ID
PRMT ENG STRT Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE: This item is displayed, but cannot be monitored
KEY SW-SLOT Indicates [On/Off] condition of key slot
TRNK/HAT MNTR
NOTE: This item is displayed, but cannot be monitored
RKE-LOCK Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE: This item is displayed, but cannot be monitored
RKE-PANIC Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-P/W OPEN Indicates [On/Off] condition of P/W DOWN signal from Intelligent Key
RKE-MODE CHG Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1 When remote keyless entry receiver (front) receives the signal transmitted while operating on Intelligent Key, the numerical value start changing
RKE OPE COUN2
NOTE: This item is displayed, but cannot be monitored
REVERSE SW(1) Indicates [On/Off] condition of R position
(1) It is displayed but does not operate on A/T models.
(2) It is displayed but does not operate on M/T models.
(3) OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
(4) For roadster models

ACTIVE TEST

TEST ITEM DESCRIPTION

Test item Description
BATTERY SAVER This test is able to check interior room lamp operation
The interior room lamp is activated after "On" on CONSULT-III screen is touched
PW REMOTO DOWN SET This test is able to check power window down operation
The power window down is activated after "On" on CONSULT-III screen is touched
OUTSIDE BUZZER This test is able to check Intelligent Key warning buzzer operation
The Intelligent Key warning buzzer is activated after "On" on CONSULT-III screen is touched
INSIDE BUZZER This test is able to check warning chime in combination meter operation
  • Take away warning chime sounds when "Take out" on CONSULT-III screen is touched
  • Key warning chime sounds when "Key" on CONSULT-III screen is touched
  • OFF position warning chime sounds when "Knob" on CONSULT-III screen is touched
INDICATOR This test is able to check warning lamp operation
  • "KEY" Warning lamp illuminates when "Key on" on CONSULT-III screen is touched
  • "KEY" Warning lamp blinks when "Key ind" on CONSULT-III screen is touched
INT LAMP This test is able to check interior room lamp operation
The interior room lamp is activated after "On" on CONSULT-III screen is touched
LCD This test is able to check meter display information
  • Engine start information displays when "BP N" on CONSULT-III screen is touched
  • Engine start information displays when "BP I" on CONSULT-III screen is touched
  • Key ID warning displays when "ID NG" on CONSULT-III screen is touched
  • Steering lock information displays when "ROTAT" on CONSULT-III screen is touched
    NOTE: For models without steering look unit, "ROTAT" is displayed but cannot be tested.
  • P position warning displays when "SFT P" on CONSULT-III screen is touched
  • Intelligent Key insert information displays when "INSRT" on CONSULT-III screen is touched
  • Intelligent Key low battery warning displays when "BATT" on CONSULT-III screen is touched
  • Take away through window warning displays when "NO KY" on CONSULT-III screen is touched
  • Take away warning display when "OUTKEY" on CONSULT-III screen is touched
  • OFF position warning display when "LK WN" on CONSULT-III screen is touched
TRUNK/GLASS HATCH
NOTE: This item is displayed, but cannot be tested
FLASHER This test is able to check hazard warning lamp operation
The hazard warning lamps are activated after "LH/RH/Off" on CONSULT-III screen is touched
HORN This test is able to check horn operation
The horn is activated after "On" on CONSULT-III screen is touched
P RANGE(1) This test is able to check A/T shift selector power supply
A/T shift selector power is supplied when "On" on CONSULT-III screen is touched
ENGINE SW ILLUMI This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when "On" on CONSULT-III screen is touched
LOCK INDICATOR This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when "On" on CONSULT-III screen is touched
ACC INDICATOR This test is able to check ACC indicator in push-ignition switch operation
ACC indicator in push-ignition switch illuminates when "On" on CONSULT-III screen is touched
IGNITION ON IND This test is able to check ON indicator in push-ignition switch operation
ON indicator in push-ignition switch illuminates when "On" on CONSULT-III screen is touched
KEY SLOT ILLUMI This test is able to check key slot illumination operation
Key slot illumination blinks when "On" on CONSULT-III screen is touched
TRUNK/BACK DOOR This test is able to check back door opener actuator/trunk lid opener actuator(2) open operation
This actuator opens when "Open" on CONSULT-III screen is touched
(1) It is displayed but does not operate on M/T models.
(2) For roadster models
scientia non olet · About LEMON Manuals