| C1101 |
When an open circuit is detected in rear RH wheel sensor circuit. |
The following functions are suspended.
- VDC function
- TCS function
- ABS function
- EBD function (only when both 2 rear wheels are malfunctioning)
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1102 |
When an open circuit is detected in rear LH wheel sensor circuit. |
| C1103 |
When an open circuit is detected in front RH wheel sensor circuit. |
| C1104 |
When an open circuit is detected in front LH wheel sensor circuit. |
| C1105 |
- When power supply voltage of rear RH wheel sensor is low.
- When distance between rear RH wheel sensor and rear RH wheel sensor rotor is large.
- When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not normal.
|
| C1106 |
- When power supply voltage of rear LH wheel sensor is low.
- When distance between rear LH wheel sensor and rear LH wheel sensor rotor is large.
- When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not normal.
|
| C1107 |
- When power supply voltage of front RH wheel sensor is low.
- When distance between front RH wheel sensor and front RH wheel sensor rotor is large.
- When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
|
| C1108 |
- When power supply voltage of front LH wheel sensor is low.
- When distance between front LH wheel sensor and front LH wheel sensor rotor is large.
- When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
|
| C1109 |
- When ignition voltage is 10 V or less.
- When ignition voltage is 16 V or more.
|
The following functions are suspended.
- VDC function
- TCS function
- ABS function
- EBD function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1111 |
When a malfunction is detected in motor or motor relay. |
| C1115 |
When difference in wheel speed between any wheel and others is detected during the vehicle is driven, because of installation of other tires than specified. |
The following functions are suspended.
- VDC function
- TCS function
- ABS function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1116 |
When stop lamp switch signal is not input when brake pedal operates. |
| C1120 |
When a malfunction is detected in front LH ABS IN valve. |
The following functions are suspended.
- VDC function
- TCS function
- ABS function
- EBD function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1121 |
When a malfunction is detected in front LH ABS OUT valve. |
| C1122 |
When a malfunction is detected in front RH ABS IN valve. |
| C1123 |
When a malfunction is detected in front RH ABS OUT valve. |
| C1124 |
When a malfunction is detected in rear LH ABS IN valve. |
| C1125 |
When a malfunction is detected in rear LH ABS OUT valve. |
| C1126 |
When a malfunction is detected in rear RH ABS IN valve. |
| C1127 |
When a malfunction is detected in rear RH ABS OUT valve. |
| C1130 |
When a malfunction is detected in ECM system. |
The following functions are suspended.
- VDC function
- TCS function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1138 |
When a malfunction is detected in 4 Wheel Active Steer system. |
| C1140 |
When a malfunction is detected in actuator relay. |
The following functions are suspended.
- VDC function
- TCS function
- ABS function
- EBD function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1142 |
When a malfunction is detected in pressure sensor. |
The following functions are suspended.
- VDC function
- TCS function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1143 |
When a malfunction is detected in steering angle sensor. |
| C1144 |
When neutral position adjustment of steering angle sensor is not complete. |
| C1145 |
When a malfunction is detected in yaw rate signal. |
| C1146 |
When a malfunction is detected in side/decel G signal. |
The following functions are suspended.
- VDC function
- TCS function
- ABS function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1155 |
When brake fluid level low signal is detected. |
| C1160 |
When calibration of yaw rate/side/decel G sensor is not complete. |
The following functions are suspended.
- VDC function
- TCS function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1164 |
When a malfunction is detected in cut valve 1. |
The following functions are suspended.
- VDC function
- TCS function
- ABS function
- EBD function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| C1165 |
When a malfunction is detected in cut valve 2. |
| C1170 |
When the information in ABS actuator and electric unit (control unit) is not the same. |
| C1197 |
When a malfunction is detected in vacuum sensor. |
Electrical vacuum assistance of brake booster is suspended. |
| C1198 |
- When an open circuit is detected in vacuum sensor circuit.
- When a short circuit is detected in vacuum sensor circuit.
- When a malfunction is detected in vacuum sensor noise.
|
| C1199 |
When brake booster vacuum is approx. 0 kPa (0 mmHg) during engine running. |
- |
| C119A |
When a malfunction is detected in supply power voltage of vacuum sensor. |
Electrical vacuum assistance of brake booster is suspended. |
| U1000 |
When CAN communication signal is not continuously received for 2 seconds or more. |
The following functions are suspended.
- VDC function
- TCS function
- hill start assist function
- Rise-up & Build-up function
- Brake force distribution function
|
| U0424 |
When signal that is transmitted from A/C auto AMP. is not the latest information. |
Mode is fixed to the mode when a malfunction of drive mode selector occurs. The mode is fixed to STANDARD mode after ignition switch turns OFF to ON. |