Specifications Index
RODEO & RODEO SPORT SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | NA | ||
| Rear | NA | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING PROCEDURE | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE SPECIFICATIONS . | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | ON-VEHICLE TESTING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | SERPENTINE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | |||
| 2.2L | 15.7 psi | ||
| 3.2L | 13.5-17.8 psi | ||
| Thermostat R & I | |||
| 3.2L | REMOVALINSTALLATION | ||
| Water Pump R & I | |||
| 3.2L | REMOVAL & INSTALLATION | ||
| Engine Mechanical | |||
| 2.2L | |||
| Compression | NA | ||
| Oil Pressure | Oil pressure at idle speed is 150 kPa (21.8 psi). | ||
| Overhaul | ENGINE MAIN SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.2L | |||
| Compression | NA | ||
| Oil pressure | Oil pressure at curb idle is 57-80 psi (3.9-5.6 kg/cm2 ) at 3000 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate | |||
| 2.2L | NA | ||
| 3.2L (Flywheel Bolt) | 54 N.m (40 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | At curb Idle Standard value: Approximately : 47 psi (324 kPa) | ||
| Fuel Pressure Test Procedure | FUEL PUMP PRESSURE TEST | ||
| Fuel Filter Location | FUEL FILTER | ||
| Fuel Filter R & I | REMOVAL & INSTALLATION (2.2L & 3.2L) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.2L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.2L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug | |||
| 2.2L | |||
| Type | NGK: K16PR-P11/ PK16PR11/ RC10PYP4 | ||
| Gap | NA | ||
| Torque | NA | ||
| 3.2L | |||
| Type | NGK: K16PR-P11/ PK16PR11/ RC10PYP4 | ||
| Gap | Standard Value: 0.040-0.043 in. (1.0-1.1 mm). | ||
| Torque | 18N.m (13 ft-lb) | ||
| Starting | |||
| Starter | |||
| 2.2L | NA | ||
| 3.2L | STARTER SPECIFICATIONS | ||
| Torque | |||
| 2.2L | TORQUE SPECIFICATIONS | ||
| 3.2L | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 87 ft. lbs. (118 N.m) | ||