Restraints Control Module (RCM)

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT ONE MINUTE. FAILURE TO FOLLOW THIS INSTRUCTION MAY RESULT IN PERSONAL INJURY.

WARNING: Do not use a multimeter to probe the restraints control module. It is possible for the power from the meter battery to trigger the activation of the airbags. Failure to follow this instruction may result in personal injury

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle

CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00

NOTE: It is advisable not to use a cellular phone or to have a cellular phone in close proximity when working on the restraints control module or associated systems

NOTE: Given the legal implications of a restraints system failure, harness repairs to Air Bag module circuits are not acceptable. Where the text refers to "REPAIR the circuit", this will normally mean the replacement of a harness.

NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the warranty policy and procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to the installation of a new module/component.

NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system)

NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests

NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion

NOTE: If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals

NOTE: Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the manufacturers approved diagnostic system

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the restraints control module, for additional diagnosis and testing information refer to the relevant diagnosis and testing section. For additional information, refer to DIAGNOSIS AND TESTING .

DTC	Description	Possible Cause	Action
B0001-11	Driver Frontal Stage 1 Deployment Control - circuit short to ground	Wiring harness fault Clockspring fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 1 circuit for short circuit to ground Check for intermittent shorts to ground within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0001-12	Driver Frontal Stage 1 Deployment Control - circuit short to battery	Wiring harness fault Clockspring fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 1 circuit for short circuit to power Check for intermittent shorts to power within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required
B0001-13	Driver Frontal Stage 1 Deployment Control - circuit open	Wiring harness fault Clockspring fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 1 circuit for open circuit, high resistance Check for intermittent open circuit, high resistance faults within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0001-1A	Driver Frontal Stage 1 Deployment Control - circuit resistance below threshold	Wiring harness fault Clockspring fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 1 circuit for short circuit between the power and return circuit lines Check for intermittent short circuits within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0001-2B	Driver Frontal Stage 1 Deployment Control - signal cross coupled	Wiring harness fault Clockspring fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 1 circuit for short circuits to other firing circuits Check for intermittent short circuits within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required
B0001-56	Driver Frontal Stage 1 Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0002-11	Driver Frontal Stage 2 Deployment Control - circuit short to ground	Wiring harness fault Clockspring fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 2 circuit for short circuit to ground Check for intermittent shorts to ground within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0002-12	Driver Frontal Stage 2 Deployment Control - circuit short to battery	Wiring harness fault Clockspring fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 2 circuit for short circuit to power Check for intermittent shorts to power within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required
B0002-13	Driver Frontal Stage 2 Deployment Control - circuit open	Wiring harness fault Clockspring fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 2 circuit for open circuit, high resistance Check for intermittent open circuit, high resistance faults within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0002-1A	Driver Frontal Stage 2 Deployment Control - circuit resistance below threshold	Wiring harness fault Clockspring fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 2 circuit for short circuit between the power and return circuit lines Check for intermittent short circuits within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0002-2B	Driver Frontal Stage 2 Deployment Control - signal cross coupled	Wiring harness fault Clockspring fault	Refer to the electrical wiring diagrams and check the driver frontal air bag stage 2 circuit for short circuits to other firing circuits Check for intermittent short circuits within the clockspring by rotating the steering column during the checks If a wiring fault is detected, repair or replace as required
B0002-56	Driver Frontal Stage 2 Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0010-11	Passenger Frontal Stage 1 Deployment Control - circuit short to ground	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 1 circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0010-12	Passenger Frontal Stage 1 Deployment Control - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 1 circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B0010-13	Passenger Frontal Stage 1 Deployment Control - open circuit	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 1 circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0010-1A	Passenger Frontal Stage 1 Deployment Control - circuit resistance below threshold	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 1 circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0010-2B	Passenger Frontal Stage 1 Deployment Control - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 1 circuit for short circuits to other firing circuits If a wiring fault is detected, repair or replace as required
B0010-56	Passenger Frontal Stage 1 Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0011-11	Passenger Frontal Stage 2 Deployment Control - circuit short to ground	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 2 circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0011-12	Passenger Frontal Stage 2 Deployment Control - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 2 circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B0011-13	Passenger Frontal Stage 2 Deployment Control - open circuit	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 2 circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0011-1A	Passenger Frontal Stage 2 Deployment Control - circuit resistance below threshold	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 2 circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0011-2B	Passenger Frontal Stage 2 Deployment Control - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger frontal air bag stage 2 circuit for short circuits to other firing circuits If a wiring fault is detected, repair or replace as required
B0011-56	Passenger Frontal Stage 2 Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0020-11	Left Side Air Bag Deployment Control - circuit short to ground	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the left side air bag circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0020-12	Left Side Air Bag Deployment Control - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the left side air bag circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B0020-13	Left Side Air Bag Deployment Control - open circuit	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the left side air bag circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0020-1A	Left Side Air Bag Deployment Control - circuit resistance below threshold	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the left side air bag circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0020-2B	Left Side Air Bag Deployment Control - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the left side air bag circuit for short circuits to other firing circuits If a wiring fault is detected, repair or replace as required
B0020-56	Left Side Air Bag Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0021-11	Left Curtain Deployment Control 1 - circuit short to ground	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the left curtain air bag circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0021-12	Left Curtain Deployment Control 1 - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the left curtain air bag circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B0021-13	Left Curtain Deployment Control 1 - open circuit	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the left curtain air bag circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0021-1A	Left Curtain Deployment Control 1 - circuit resistance below threshold	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the left curtain air bag circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0021-2B	Left Curtain Deployment Control 1 - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the left curtain air bag circuit for short circuits to other firing circuits If a wiring fault is detected, repair or replace as required
B0021-56	Left Curtain Deployment Control 1 - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0028-11	Right Side Air Bag Deployment Control - circuit short to ground	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the right side air bag circuit for short circuit to groundc If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0028-12	Right Side Air Bag Deployment Control - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the right side air bag circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B0028-13	Right Side Air Bag Deployment Control - open circuit	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the right side air bag circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0028-1A	Right Side Air Bag Deployment Control - circuit resistance below threshold	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the right side air bag circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0028-2B	Right Side Air Bag Deployment Control - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the right side air bag circuit for short circuits to other firing circuits If a wiring fault is detected, repair or replace as required
B0028-56	Right Side Air Bag Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0029-11	Right Curtain Deployment Control 1 - circuit short to ground	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the right curtain air bag circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0029-12	Right Curtain Deployment Control 1 - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the right curtain air bag circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B0029-13	Right Curtain Deployment Control 1 - open circuit	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the right curtain air bag circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0029-1A	Right Curtain Deployment Control 1 - Circuit resistance below threshold	Wiring harness fault Air bag squib component fault	Refer to the electrical wiring diagrams and check the right curtain air bag circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new firing squib. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0029-2B	Right Curtain Deployment Control 1 - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the right curtain air bag circuit for short circuits to other firing circuits If a wiring fault is detected, repair or replace as required
B0029-56	Right Curtain Deployment Control 1 - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0050-11	Driver Safety Belt Sensor - circuit short to ground	Wiring harness fault Safety belt sensor internal fault	Refer to the electrical wiring diagrams and check the driver safety belt sensor hall switch signal circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check switch circuit in the buckle, replace buckle as required
B0050-12	Driver Safety Belt Sensor - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the driver safety belt sensor hall switch signal circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B0050-13	Driver Safety Belt Sensor - circuit open	Wiring harness fault Safety belt sensor internal fault	Refer to the electrical wiring diagrams and check the driver safety belt sensor hall switch signal circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check switch circuit in the buckle, replace buckle as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0050-1D	Driver Safety Belt Sensor - circuit current out of range	Wiring harness fault Safety belt sensor internal fault	Refer to the electrical wiring diagrams and check the driver safety belt sensor hall switch signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check switch circuit in the buckle, replace buckle as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0050-2B	Driver Safety Belt Sensor - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the driver safety belt sensor hall switch signal circuit for short circuit to another hall switch circuit If a wiring fault is detected, repair or replace as required
B0050-56	Driver Safety Belt Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0052-11	Passenger Safety Belt Sensor - circuit short to ground	Wiring harness fault Safety belt sensor internal fault	Refer to the electrical wiring diagrams and check the passenger safety belt sensor hall switch signal circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check switch circuit in the buckle, replace buckle as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0052-12	Passenger Safety Belt Sensor - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger safety belt sensor hall switch signal circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B0052-13	Passenger Safety Belt Sensor - circuit open	Wiring harness fault Safety belt sensor internal fault	Refer to the electrical wiring diagrams and check the passenger safety belt sensor hall switch signal circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check switch circuit in the buckle, replace buckle as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0052-1D	Passenger Safety Belt Sensor - circuit current out of range	Wiring harness fault Safety belt sensor internal fault	Refer to the electrical wiring diagrams and check the passenger safety belt sensor hall switch signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check switch circuit in the buckle, replace buckle as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B0052-2B	Passenger Safety Belt Sensor - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger safety belt sensor hall switch signal circuit for short circuit to another hall switch circuit If a wiring fault is detected, repair or replace as required
B0052-56	Passenger Safety Belt Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0090-11	Left Frontal Restraints Sensor - circuit short to ground	Wiring harness fault	Refer to the electrical wiring diagrams and check the left front side impact sensor circuit for short circuit to ground If a wiring fault is detected, repair or replace as required
B0090-15	Left Frontal Restraints Sensor - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the left front side impact sensor circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B0090-56	Left Frontal Restraints Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0090-81	Left Frontal Restraints Sensor - invalid serial data received	Wiring harness fault Sensor fault	Refer to the electrical wiring diagrams and check the left front side impact sensor circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new sensor, clear the DTC and retest the system
B0090-96	Left Frontal Restraints Sensor - component internal failure	Internal component failure	Install a new sensor, clear the DTC and retest the system
B0092-11	Left Side Restraints Sensor 2 - circuit short to ground	Wiring harness fault	Refer to the electrical wiring diagrams and check the left rear side impact sensor circuit for short circuit to ground If a wiring fault is detected, repair or replace as required
B0092-15	Left Side Restraints Sensor 2 - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the left rear side impact sensor circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B0092-56	Left Side Restraints Sensor 2 - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0092-81	Left Side Restraints Sensor 2 - invalid serial data received	Wiring harness fault Sensor fault	Refer to the electrical wiring diagrams and check the left rear side impact sensor circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new sensor, clear the DTC and retest the system
B0092-96	Left Side Restraints Sensor 2 - component internal failure	Internal component failure	Install a new sensor, clear the DTC and retest the system
B0095-11	Right Frontal Restraints Sensor - circuit short to ground	Wiring harness fault	Refer to the electrical wiring diagrams and check the right front side impact sensor circuit for short circuit to ground If a wiring fault is detected, repair or replace as required
B0095-15	Right Frontal Restraints Sensor - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the right front side impact sensor circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B0095-56	Right Frontal Restraints Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0095-81	Right Frontal Restraints Sensor - invalid serial data received	Wiring harness fault Sensor fault	Refer to the electrical wiring diagrams and check the right front side impact sensor circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new sensor, clear the DTC and retest the system
B0095-96	Right Frontal Restraints Sensor - component internal failure	Internal component failure	Install a new sensor, clear the DTC and retest the system
B0097-11	Right Side Restraints Sensor 2 - circuit short to ground	Wiring harness fault	Refer to the electrical wiring diagrams and check the right rear side impact sensor circuit for short circuit to ground If a wiring fault is detected, repair or replace as required
B0097-15	Right Side Restraints Sensor 2 - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the right rear side impact sensor circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B0097-56	Right Side Restraints Sensor 2 - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B0097-81	Right Side Restraints Sensor 2 - invalid serial data received	Wiring harness fault Sensor fault	Refer to the electrical wiring diagrams and check the right rear side impact sensor circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new sensor, clear the DTC and retest the system
B0097-96	Right Side Restraints Sensor 2 - component internal failure	Internal component failure	Install a new sensor, clear the DTC and retest the system
B00B5-11	Driver Seat Track Position Restraints Sensor - circuit short to ground	Wiring harness fault Seat position sensor internal fault	Refer to the electrical wiring diagrams and check the drivers seat position sensor circuit for short circuit to ground If a wiring fault is detected, repair or replace as required Check and install new seat position sensor as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00B5-12	Driver Seat Track Position Restraints Sensor - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the drivers seat position sensor circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B00B5-13	Driver Seat Track Position Restraints Sensor - circuit open	Wiring harness fault Seat position sensor internal fault	Refer to the electrical wiring diagrams and check the drivers seat position sensor circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required Check and install new seat position sensor as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00B5-1D	Driver Seat Track Position Restraints Sensor - circuit current out of range	Wiring harness fault Seat position sensor internal fault	Refer to the electrical wiring diagrams and check the drivers seat position sensor circuit for short circuit to ground, short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new seat position sensor as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00B5-2B	Driver Seat Track Position Restraints Sensor - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the drivers seat position sensor circuit for short circuit to another sensing device If a wiring fault is detected, repair or replace as required
B00B5-56	Driver Seat Track Position Restraints Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B00C5-11	Passenger Seat Track Position Restraints Sensor - circuit short to ground	Wiring harness fault Seat position sensor internal fault	Refer to the electrical wiring diagrams and check the passenger seat position sensor circuit for short circuit to ground If a wiring fault is detected, repair or replace as required Check and install new seat position sensor as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00C5-12	Passenger Seat Track Position Restraints Sensor - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger seat position sensor circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B00C5-13	Passenger Seat Track Position Restraints Sensor - circuit open	Wiring harness fault Seat position sensor internal fault	Refer to the electrical wiring diagrams and check the passenger seat position sensor circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required Check and install new seat position sensor as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00C5-1D	Passenger Seat Track Position Restraints Sensor - circuit current out of range	Wiring harness fault Seat position sensor internal fault	Refer to the electrical wiring diagrams and check the passenger seat position sensor circuit for short circuit to ground, short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new seat position sensor as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00C5-2B	Passenger Seat Track Position Restraints Sensor - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger seat position sensor circuit for short circuit to another sensing device If a wiring fault is detected, repair or replace as required
B00C5-56	Passenger Seat Track Position Restraints Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B00D2-01	Restraint System Malfunction Indicator 1 - general electrical failure	A problem with the restraint system warning lamp was reported through the CAN network by the instrument cluster	Check the instrument cluster for relevant DTCs and refer to the DTC index for that module
B00D5-11	Restraint System Passenger Disable Indicator - circuit short to ground	Wiring harness fault Overhead console fault	Refer to the electrical wiring diagrams and check the airbag deactivation lamp circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring fault is detected, check the overhead console passenger airbag deactivation lamp circuit for short circuit to ground. If a wiring fault is detected, repair or replace as required
B00D5-12	Restraint System Passenger Disable Indicator - circuit short to battery	Wiring harness fault Overhead console fault	Refer to the electrical wiring diagrams and check the airbag deactivation lamp circuit for short circuit to power If a wiring fault is detected, repair or replace as required If no wiring fault is detected, check the overhead console passenger airbag deactivation lamp circuit for short circuit to power. If a wiring fault is detected, repair or replace as required
B00D5-13	Restraint System Passenger Disable Indicator - circuit open	Wiring harness fault Overhead console fault	Refer to the electrical wiring diagrams and check the airbag deactivation lamp circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring fault is detected, check the overhead console passenger airbag deactivation lamp circuit for open circuit, high resistance. If a wiring fault is detected, repair or replace as required
B00D5-56	Restraint System Passenger Disable Indicator - invalid/incomplete configuration	The indicator device is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system Check the integrity of the airbag deactivation lamp circuit wiring harness and check that harness connectors are correctly seated and not mis-pinned
B00DF-11	Passenger Restraints Disable Switch - circuit short to ground	Wiring harness fault Switch fault	Refer to the electrical wiring diagrams and check the passenger airbag disable switch circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring fault is detected, check and install new passenger airbag disable switch Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00DF-12	Passenger Restraints Disable Switch - circuit short to battery	Wiring harness fault Switch fault	Refer to the electrical wiring diagrams and check the passenger airbag disable switch circuit for short circuit to power If a wiring fault is detected, repair or replace as required If no wiring fault is detected, check and install new passenger airbag disable switch Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00DF-13	Passenger Restraints Disable Switch - circuit open	Wiring harness fault Switch fault	Refer to the electrical wiring diagrams and check the passenger airbag disable switch circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring fault is detected, check and install new passenger airbag disable switch Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00DF-1D	Passenger Restraints Disable Switch - circuit current out of range	Wiring harness fault Switch fault	Refer to the electrical wiring diagrams and check the passenger airbag disable switch circuit for short circuit to ground, short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring fault is detected, check and install new passenger airbag disable switch Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B00DF-2B	Passenger Restraints Disable Switch- signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the passenger airbag disable switch circuit for short circuit to another device If a wiring fault is detected, repair or replace as required
B00DF-56	Passenger Restraints Disable Switch - invalid/incomplete configuration	The switch is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B00DF-95	Passenger Restraints Disable Switch - incorrect assembly	The switch is connected but not configured correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system Clear the DTC and retest the system
B1001-11	Right Hood Deployment Control - circuit short to ground	Wiring harness fault Right side hood latch actuator component fault	Refer to the electrical wiring diagrams and check the right side hood actuator circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new hood latch actuator Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1001-12	Right Hood Deployment Control - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the right side hood actuator circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B1001-13	Right Hood Deployment Control - open circuit	Wiring harness fault Right side hood latch actuator component fault	Refer to the electrical wiring diagrams and check the right side hood actuator circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new hood latch actuator Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1001-1A	Right Hood Deployment Control - circuit resistance below threshold	Wiring harness fault Right side hood latch actuator component fault	Refer to the electrical wiring diagrams and check the right side hood actuator circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new hood latch actuator Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1001-2B	Right Hood Deployment Control - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the right side hood actuator circuit for short circuits to other firing circuits If a wiring fault is detected, repair or replace as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1001-56	Right Hood Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
B1003-11	Left Hood Deployment Control - circuit short to ground	Wiring harness fault Left side hood latch actuator component fault	Refer to the electrical wiring diagrams and check the left side hood actuator circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new hood latch actuator Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1003-12	Left Hood Deployment Control - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the left side hood actuator circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B1003-13	Left Hood Deployment Control - open circuit	Wiring harness fault Left side hood latch actuator component fault	Refer to the electrical wiring diagrams and check the left side hood actuator circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new hood latch actuator Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1003-1A	Left Hood Deployment Control - circuit resistance below threshold	Wiring harness fault Left side hood latch actuator component fault	Refer to the electrical wiring diagrams and check the left side hood actuator circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new hood latch actuator Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1003-2B	Left Hood Deployment Control - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the left side hood actuator circuit for short circuits to other firing circuits If a wiring fault is detected, repair or replace as required
B1003-56	Left Hood Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
B1004-11	Right Frontal Impact Classification Sensor - circuit short to ground	Wiring harness fault Right side accelerometer fault	Refer to the electrical wiring diagrams and check the right side accelerometer circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new right side pedestrian protection accelerometer Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1004-15	Right Frontal Impact Classification Sensor - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the right side accelerometer circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B1004-56	Right Frontal Impact Classification Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
B1004-81	Right Frontal Impact Classification Sensor - invalid serial data received	Wiring harness fault Right side accelerometer fault	Refer to the electrical wiring diagrams and check the right side accelerometer circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new right side pedestrian protection accelerometer, clear the DTC and retest the system
B1004-96	Right Frontal Impact Classification Sensor - component internal failure	Internal component failure	Install a new sensor, clear the DTC and retest the system
B1005-11	Left Frontal Impact Classification Sensor - circuit short to ground	Wiring harness fault Left side accelerometer fault	Refer to the electrical wiring diagrams and check the left side accelerometer circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new left side pedestrian protection accelerometer Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1005-15	Left Frontal Impact Classification Sensor - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the left side accelerometer circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B1005-56	Left Frontal Impact Classification Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
B1005-81	Left Frontal Impact Classification Sensor - invalid serial data received	Wiring harness fault Left side accelerometer fault	Refer to the electrical wiring diagrams and check the left side accelerometer circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new left side pedestrian protection accelerometer, clear the DTC and retest the system
B1005-96	Left Frontal Impact Classification Sensor - component internal failure	Internal component failure	Install a new sensor, clear the DTC and retest the system
B1006-11	Center Frontal Impact Classification Sensor - circuit short to ground	Wiring harness fault Central front accelerometer fault	Refer to the electrical wiring diagrams and check the center accelerometer circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new center pedestrian protection accelerometer Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1006-15	Center Frontal Impact Classification Sensor - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the center front accelerometer circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B1006-56	Center Frontal Impact Classification Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
B1006-81	Center Frontal Impact Classification Sensor - invalid serial data received	Wiring harness fault Central front accelerometer fault	Refer to the electrical wiring diagrams and check the center accelerometer circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new center pedestrian protection accelerometer, clear the DTC and retest the system
B1006-96	Center Frontal Impact Classification Sensor - component internal failure	Internal component failure	Install a new sensor, clear the DTC and retest the system
B1193-00	Crash Event Storage Full and Locked - no sub type information	The restraints control module has stored crash events	Install a new restraints control module Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B11A0-11	Left Side Restraints Pressure Sensor - circuit short to ground	Wiring harness fault Impact sensor fault	Refer to the electrical wiring diagrams and check the left side impact pressure sensor circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new impact pressure sensor Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B11A0-15	Left Side Restraints Pressure Sensor - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the left side impact pressure sensor circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B11A0-56	Left Side Restraints Pressure Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
B11A0-81	Left Side Restraints Pressure Sensor - invalid serial data received	Wiring harness fault Impact sensor fault	Refer to the electrical wiring diagrams and check the left side impact pressure sensor circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new impact pressure sensor, clear the DTC and retest the system
B11A0-96	Left Side Restraints Pressure Sensor - component internal failure	Internal component failure	Install a new impact pressure sensor, clear the DTC and retest the system
B11A1-11	Right Side Restraints Pressure Sensor - circuit short to ground	Wiring harness fault Impact sensor fault	Refer to the electrical wiring diagrams and check the right side impact pressure sensor circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new impact pressure sensor Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B11A1-15	Right Side Restraints Pressure Sensor - circuit short to battery or open	Wiring harness fault	Refer to the electrical wiring diagrams and check the right side impact pressure sensor circuit for short circuit to power, open circuit, high resistance If a wiring fault is detected, repair or replace as required
B11A1-56	Right Side Restraints Pressure Sensor - invalid/incomplete configuration	The sensing device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
B11A1-81	Right Side Restraints Pressure Sensor - invalid serial data received	Wiring harness fault Impact sensor fault	Refer to the electrical wiring diagrams and check the right side impact pressure sensor circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If there are no wiring harness faults, check and install new impact pressure sensor, clear the DTC and retest the system
B11A1-96	Right Side Restraints Pressure Sensor - component internal failure	Internal component failure	Install a new impact pressure sensor, clear the DTC and retest the system
B11D8-11	Restraint Event Notification - circuit short to ground	Wiring harness fault	Refer to the electrical wiring diagrams and check the airbag deployed notification circuit for short circuit to ground If a wiring fault is detected, repair or replace as required
B11D8-12	Restraint Event Notification - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the airbag deployed notification circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B11D8-13	Restraint Event Notification - circuit open	Wiring harness fault	Refer to the electrical wiring diagrams and check the airbag deployed notification circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required
B11D8-68	Restraint Event Notification - event information	Event information - left and right hood deployed	The pedestrian impact protection system has deployed. Install new modules and components as required Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1212-11	Driver Safetybelt Buckle Pretensioner Deployment Control - circuit short to ground	Wiring harness fault Pretensioner component fault	Refer to the electrical wiring diagrams and check the driver pretensioner circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new driver pretensioner/buckle switch assembly. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1212-12	Driver Safetybelt Buckle Pretensioner Deployment Control - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the driver pretensioner circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B1212-13	Driver Safetybelt Buckle Pretensioner Deployment Control - circuit open	Wiring harness fault Pretensioner component fault	Refer to the electrical wiring diagrams and check the driver pretensioner circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new driver pretensioner/buckle switch assembly. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1212-1A	Driver Safetybelt Buckle Pretensioner Deployment Control - circuit resistance below threshold	Wiring harness fault Pretensioner component fault	Refer to the electrical wiring diagrams and check the driver pretensioner circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new driver pretensioner/buckle switch assembly. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1212-2B	Driver Safetybelt Buckle Pretensioner Deployment Control - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the driver pretensioner circuit for short circuits to other deployment circuits If a wiring fault is detected, repair or replace as required
B1212-56	Driver Safetybelt Buckle Pretensioner Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
B1213-11	Passenger Safetybelt Buckle Pretensioner Deployment Control - circuit short to ground	Wiring harness fault Pretensioner component fault	Refer to the electrical wiring diagrams and check the front passenger pretensioner circuit for short circuit to ground If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new passenger pretensioner/buckle switch assembly. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1213-12	Passenger Safetybelt Buckle Pretensioner Deployment Control - circuit short to battery	Wiring harness fault	Refer to the electrical wiring diagrams and check the front passenger pretensioner circuit for short circuit to power If a wiring fault is detected, repair or replace as required
B1213-13	Passenger Safetybelt Buckle Pretensioner Deployment Control - circuit open	Wiring harness fault Pretensioner component fault	Refer to the electrical wiring diagrams and check the front passenger pretensioner circuit for open circuit, high resistance If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new passenger pretensioner/buckle switch assembly. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1213-1A	Passenger Safetybelt Buckle Pretensioner Deployment Control - circuit resistance below threshold	Wiring harness fault Pretensioner component fault	Refer to the electrical wiring diagrams and check the front passenger pretensioner circuit for short circuit between the power and return circuit lines If a wiring fault is detected, repair or replace as required If no wiring faults are detected check and install a new passenger pretensioner/buckle switch assembly. Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
B1213-2B	Passenger Safetybelt Buckle Pretensioner Deployment Control - signal cross coupled	Wiring harness fault	Refer to the electrical wiring diagrams and check the front passenger pretensioner circuit for short circuits to other deployment circuits If a wiring fault is detected, repair or replace as required
B1213-56	Passenger Safetybelt Buckle Pretensioner Deployment Control - invalid/incomplete configuration	The deployable device is connected but not configured correctly	Re-configure the device using the manufacturer approved diagnostic system Clear the DTC and retest the system
P0071-29	Ambient Air Temperature Sensor Range/Performance - signal invalid	Ambient air temperature readings received via CAN network are invalid	Check the engine control module for related DTCs and refer to the relevant DTC index
P1934-29	Vehicle Speed Signal - signal invalid	Vehicle speed readings received via CAN network are invalid	Check the ABS module for related DTCs and refer to the relevant DTC index
U0001-88	High Speed CAN Communication Bus - bus off	High speed CAN failure - bus off	Refer to the electrical circuit diagrams and check the high speed CAN bus for short circuit to ground, short circuit to power, open circuit, high resistance
U0100-00	Lost communication with ECM/PCM 'A' - no sub type information	Loss of CAN communication with engine control module	Refer to the electrical circuit diagrams and check the power and ground connections to the engine control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the engine control module and the restraints control module Check the engine control module for related DTCs and refer to the relevant DTC index
U0101-00	Lost communication with TCM - no sub type information	Loss of CAN communication with transmission control module	Refer to the electrical circuit diagrams and check the power and ground connections to the transmission control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the transmission control module and the restraints control module Check the transmission control module for related DTCs and refer to the relevant DTC index
U0104-00	Lost communication with cruise control module - no sub type information	Loss of CAN communication with speed control module	Refer to the electrical circuit diagrams and check the power and ground connections to the speed control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the speed control module and the restraints control module Check the speed control module for related DTCs and refer to the relevant DTC index
U0121-00	Lost communication with Anti-lock Brake System (ABS) control module - no sub type information	Loss of CAN communication with ABS control module	Refer to the electrical circuit diagrams and check the power and ground connections to the ABS control module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the ABS control module and the restraints control module Check the ABS control module for related DTCs and refer to the relevant DTC index
U0140-00	Lost communication with Body Control Module - no sub type information	Loss of CAN communication with central junction box	Refer to the electrical circuit diagrams and check the power and ground connections to the central junction box Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the central junction box and the restraints control module Check the central junction box for related DTCs and refer to the relevant DTC index
U0142-00	Lost communication with Body Control Module B - no sub type information	Loss of CAN communication with rear junction box	Refer to the electrical circuit diagrams and check the power and ground connections to the rear junction box Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the rear junction box and the restraints control module Check the rear junction box for related DTCs and refer to the relevant DTC index
U0154-00	Lost Communication With Restraints Occupant Classification System Module - no sub type information	Loss of CAN communication with occupant classification system module	Refer to the electrical circuit diagrams and check the power and ground connections to the occupant classification system module Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the occupant classification system module and the restraints control module Check the occupant classification system module for related DTCs and refer to the relevant DTC index
U0155-00	Lost Communication With Instrument Panel Cluster (IPC) Control Module - No sub type information	Loss of CAN communication with instrument cluster	Refer to the electrical circuit diagrams and check the power and ground connections to the instrument cluster Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the instrument cluster and the restraints control module Check the instrument cluster for related DTCs and refer to the relevant DTC index
U0300-00	Internal Control Module Software Incompatibility - no sub type information	Central junction box car configuration data is not compatible with the restraints control module Master car configuration file not being transmitted by central junction box	Re-configure the central junction box using the manufacturer approved diagnostic system. Clear DTC and re-test If fault persists, check and install a new restraints control module Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module
U0455-56	Invalid Data Received From Restraints Occupant Classification System Module - invalid/incomplete configuration	Car configuration file is incorrect Incorrect seat installed	Check that the vehicle specification matches the car configuration file Check if the seat has an occupant classification sensor Check the correct car configuration file is loaded into the restraints control module Install the correct car configuration file, clear the DTC and retest the system
U0455-64	Invalid Data Received From Restraints Occupant Classification System Module - signal plausibility failure	Occupant classification system sending indeterminate status data	Check the occupant classification system control module for related DTCs and refer to the relevant DTC index Clear the DTCs in the restraints control module and retest the system
U0455-64				U0455-92
U0455-93	Invalid Data Received From Restraints Occupant Classification System Module - no operation	No operation of occupant classification system reported by occupant classification system control module	Check the occupant classification system control module for related DTCs and refer to the relevant DTC index Clear the DTCs in the restraints control module and retest the system
U0455-95	Invalid Data Received From Restraints Occupant Classification System Module - incorrect assembly	The occupant classification system control module is programmed with a different calibration from that contained in the restraints control module	Verify components installed are correct for this vehicle. Check if the seat is correct, check the occupant classification system control module and the restraints control module are valid and correctly programmed
U1A14-46	CAN Initialisation Failure - calibration/parameter memory failure	Restraints control module internal fault - corrupt non-volatile memory	Clear DTC and retest. If fault persists, check and install a new restraints control module Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U201A-57	Control Module Main Calibration Data - invalid/incomplete software component	Restraints control module not programmed correctly Car configuration file - Model year and/or vehicle type set incorrectly	Re-configure the restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test
U201B-57	Control Module Main Calibration Data #2 - invalid/incomplete software component	Restraints control module not programmed correctly Car configuration file - Parameter settings invalid	Re-configure the restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test
U2100-00	Initial Configuration Not Complete - No sub type information	Restraints control module not correctly configured	Configure the restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test
U2101-00	Control Module Configuration Incompatible - no sub type information	Restraints control module not correctly configured	Configure the restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test
U2200-00	Control Module Configuration Memory Corrupt - no sub type information	Restraints control module configuration memory fault	Re-configure the restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test
U2300-54	Central Configuration - missing calibration	Configuration missing	Check/amend the car configuration file using the manufacturer approved diagnostic system
U3000-46	Control module - calibration/parameter memory failure	Restraints control module internal fault - corrupt non-volatile memory	Clear DTC and retest. If fault persists, check and install a new restraints control module Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U3000-49	Control module - internal electronic failure	Restraints control module internal fault	Clear DTC and retest. If fault persists, check and install a new restraints control module Refer to the warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new module/component
U3002-51	Vehicle Identification Number - not programmed	Restraints control module not programmed correctly	Re-configure the restraints control module using the manufacturer approved diagnostic system. Clear DTC and re-test
U3003-17	Battery voltage - circuit voltage above threshold	Circuit voltage > 16 volts threshold	Refer to relevant section of workshop manual and battery care manual. Check battery state of charge and starting/charging system performance
U3003-62	Battery voltage - signal compare failure	Signal compare failure Restraints control module voltage differs more than ±2V compared to central electronics module voltage	Refer to relevant section of workshop manual and battery care manual. Check battery state of charge and starting/charging system performance. Check power supply circuit from central junction box to restraints control module Refer to electrical wiring diagrams and check the power and ground supply circuits to the module. Repair wiring harness as required. Clear DTC and retest