Specifications Index
WRANGLER SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | N/A | ||
| Axle Nut/Hub Nut | 175 Ft. Lbs. (237 N.m) | ||
| Brakes | |||
| Bleeding Sequence | |||
| With ABS | BLEEDING BRAKE SYSTEM | ||
| Without ABS | BLEEDING SEQUENCE | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | See GENERATOR APPLICATION table under IDENTIFICATION . | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 12-18 psi | ||
| Water Pump R & I | |||
| 2.5L | WATER PUMP | ||
| 4.0L | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | |||
| 2.5L | Normal oil pressure should be 13 psi (0.9 kg/cm2 ) at 600 RPM, 25-35 psi (1.8-2.5 kg/cm2 ) at 800 RPM and 37-75 psi (2.6-5.3 kg/cm2 ) at 1600 RPM. Oil pressure relief occurs at 75 psi (5.3 kg/cm2 ). | ||
| 4.0L | Minimum oil pressure should be 13 psi (.9 kg/cm2 ) at 600 RPM. Normal oil pressure should be 37-75 psi (3-5 kg/cm2 ) at greater than 1600 RPM. Oil pressure relief is 75 psi (5 kg/cm2 ). | ||
| Overhaul | |||
| 2.5L | ENGINE SPECIFICATIONS | ||
| 4.0L | ENGINE SPECIFICATIONS | ||
| Torque | |||
| 2.5L | TORQUE SPECIFICATIONS | ||
| 4.0L | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Drive Plate/Flex Plate Torque | |||
| 2.5L | |||
| Flexplate-To-Crankshaft Bolt (A/T) | 105 Ft. Lbs. (143 N.m) | ||
| Flywheel-To-Crankshaft Bolt (M/T) | 50 Ft. Lbs. (68 N.m) Tighten an additional 60 degrees. | ||
| 4.0L | |||
| Flexplate-To-Crankshaft Bolts | 55 Ft. Lbs. (75 N.m) | ||
| Flywheel-To-Crankshaft Bolts | 105 Ft. Lbs. (143 N.m) | ||
| Fuel System | |||
| Fuel Filter Location | FUEL FILTER | ||
| Pressure Specification | FUEL PUMP | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Pressure Release Procedure | FUEL SYSTEM PRESSURE RELEASE | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | FIRING ORDER Wire routing is located in Figures. | ||
| Spark Plugs | SPARK PLUGS | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Lug Nut Torque | 85-115 Ft. Lbs. (115-156 N.m) | ||