Diagnostic Test

1) CHECK FOR DTC B1D67-ADJUSTABLE PEDAL CONTROL CIRCUIT PERFORMANCE
NOTE: This DTC must be active for the results of this test to be valid.

Turn the ignition on.

With the scan tool, record and erase DTC's.

Cycle the ignition switch from off to on.

Cycle and hold the Adjustable Pedals Switch forward, rearward, and forward at two second intervals.

With the scan tool, read DTC's

Does the scan tool display: B1D67-ADJUSTABLE PEDAL CONTROL CIRCUIT PERFORMANCE?

Yes
1. Go to 2).
No
1. The condition that caused the symptom is currently not present. Inspect the related wiring for a possible intermittent condition. Look for any chafed, pierced, pinched, or partially broken wires.
2. Refer to the APS-INTERMITTENT CONDITION TEST .
2) CHECK CONNECTOR/TERMINAL FOR DAMAGE
NOTE: Check all terminals for broken, bent, pushed out, or corroded terminals.

Turn the ignition off.

Inspect the Memory Seat Module harness connector, Adjustable Pedals Motor, and Adjustable Pedals Motor harness connector.

Is the Adjustable Pedals Motor or any of the connectors/terminals damaged?

Yes
1. Repair as necessary.
2. Perform APS VERIFICATION TEST .
No
1. Go to 3).
3) CHECK ADJUSTABLE PEDALS ASSEMBLY FOR MECHANICAL DAMAGE
Inspect the Adjustable Pedals Assembly for any physical damage.

NOTE: Check for any conditions that would cause the motor to stall or be stuck.

Is the Adjustable Pedals Assembly damaged or broken?

Yes
1. Replace the Adjustable Pedals Assembly in accordance with the Service Information.
2. Perform APS VERIFICATION TEST .
No
1. Go to 4).
4) CHECK (P205) ADJUSTABLE PEDALS MOTOR FORWARD CIRCUIT FOR AN OPEN

Fig 1: Checking Adjustable Pedals Motor Rearward Circuit
Courtesy of CHRYSLER LLC

Disconnect the Memory Seat Module harness connector.

Disconnect the Adjustable Pedals Motor harness connector

Connect a jumper wire between the (P205) Adjustable Pedals Motor Forward circuit and ground in the Adjustable Pedal Motor harness connector.

Using a 12-volt test light connected to 12-volts, probe the (P205) Adjustable Pedals Motor Forward circuit in the Memory Seat Module harness connector.

Does the test light illuminate brightly?

Yes
1. Go to 5).
No
1. Repair the Adjustable Pedals Motor Forward circuit for an open.
2. Perform APS VERIFICATION TEST .
5) CHECK (P206) ADJUSTABLE PEDALS MOTOR REARWARD CIRCUIT FOR AN OPEN

Fig 2: Checking Adjustable Pedals Motor Rearward Circuit
Courtesy of CHRYSLER LLC

Connect a jumper wire between the Adjustable Pedals Motor Rearward circuit and ground in the Adjustable Pedal Motor harness connector.

Using a 12-volt test light connected to 12-volts, probe the (P206) Adjustable Pedals Motor Rearward circuit in the Memory Seat Module harness connector.

Does the test light illuminate brightly?

Yes
1. Go to 6).
No
1. Repair the (P206) Adjustable Pedals Motor Rearward circuit for an open.
2. Perform APS VERIFICATION TEST .
6) CHECK (G912) SENSOR RETURN CIRCUIT FOR AN OPEN

Fig 3: Checking Sensor Return Circuit
Courtesy of CHRYSLER LLC

Connect a jumper wire between the (G912) Sensor Return circuit and ground in the Adjustable Pedal Motor harness connector.

Using a 12-volt test light connected to 12-volts, probe the (G912) Sensor Return circuit.

Does the test light illuminate brightly?

Yes
1. Go to 7).
No
1. Repair the (G912) Sensor Return circuit for an open.
2. Perform APS VERIFICATION TEST .
7) CHECK ADJUSTABLE PEDALS MOTOR

Fig 4: Checking Adjustable Pedals Motor
Courtesy of CHRYSLER LLC

Measure the resistance between the (P205) Adjustable Pedals Motor Forward and (P206) Adjustable Pedals Motor Rearward terminals at the Adjustable Pedals Motor.

Is the resistance below 100.0 ohms?

Yes
1. Replace and reprogram the Memory Seat Module in accordance with the Service Information.
2. Perform APS VERIFICATION TEST .
No
1. Replace the Adjustable Pedals Motor in accordance with the Service Information.
2. Perform APS VERIFICATION TEST .