Diagnostic Test

DTC IS ACTIVE
NOTE: Diagnose and repair any system voltage or sensor reference voltage DTCs before continuing with this test.
1. Start the engine and allow it to reach normal operating temperature.
  WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
2. With the scan tool, select View DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go to step 2
  No
  - Perform the CHECKING FOR AN INTERMITTENT DTC diagnostic procedure. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
(K857) 5-VOLT SUPPLY CIRCUIT VOLTAGE

Fig 1: Checking 5-Volt Supply Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Disconnect the Manifold Flow Valve connector.
3. Turn the ignition on.
4. Measure the voltage of the (K857) 5-Volt Supply circuit in the Manifold Flow Valve harness connector.
  Is the voltage above 4.5 volts?
  
  Yes
  - Go to step 6
  No
  - Go to step 3
(K857) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND

Fig 2: Checking 5-Volt Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition on.
2. Disconnect the Powertrain Control Module (PCM) C2 harness connector.
3. Measure the resistance between ground and the (K857) 5-Volt Supply circuit in the Manifold Flow Valve harness connector.
  Is the resistance above 1000 Ohms?
  
  Yes
  - Go to step 4
  No
  - Repair the (K857) 5-Volt Supply circuit for a short to ground.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
(K857) 5-VOLT SUPPLY CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT

Fig 3: Checking 5-Volt Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between the (K857) 5-Volt Supply circuit and the (K900) Sensor Ground circuit in the Manifold Flow Valve harness connector.
  Is the resistance above 100 Ohms?
  
  Yes
  - Go to step 5
  No
  - Repair the (K857) 5-Volt Supply circuit for a short to the (K900) Sensor Ground circuit.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
(K857) 5-VOLT SUPPLY CIRCUIT OPEN OR HIGH RESISTANCE

Fig 4: Checking 5-Volt Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance of the (K857) 5-Volt Supply circuit between the Manifold Flow Valve harness connector and the Powertrain Control Module (PCM) harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Go to step 10
  No
  - Repair the (K857) 5-Volt Supply circuit for an open circuit or high resistance.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
(K602) MFV SIGNAL CIRCUIT SHORTED TO GROUND

Fig 5: Checking MFV Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Disconnect the Powertrain Control Module (PCM) C2 harness connector.
3. Measure the resistance between ground and the (K602) MFV Signal circuit in the Manifold Flow Valve harness connector.
  Is the resistance above 100 Ohms?
  
  Yes
  - Go to step 7
  No
  - Repair the (K602) MFV Signal circuit for a short to ground.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
(K602) MFV SIGNAL CIRCUIT SHORTED TO (K900) SENSOR GROUND CIRCUIT

Fig 6: Checking MFV Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between the (K602) MFV Signal circuit and the (K900) Sensor Ground circuit in the Manifold Flow Valve harness connector.
  Is the resistance above 100 Ohms?
  
  Yes
  - Go to step 8
  No
  - Repair the (K602) MFV Signal circuit for a short to the (K900) Sensor Ground circuit.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
(K602) MFV SIGNAL CIRCUIT OPEN OR HIGH RESISTANCE

Fig 7: Checking MFV Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance of the (K602) MFV Signal circuit between the Manifold Flow Valve harness connector and the Powertrain Control Module (PCM) harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Go to step 9
  No
  - Repair the (K602) MFV Signal circuit for an open circuit or high resistance.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
MANIFOLD FLOW VALVE

Fig 8: Checking MFV Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Connect the Powertrain Control Module (PCM) harness connector.
3. Connect a jumper wire between the (K857) 5-Volt Supply circuit and the (K602) MFV Signal circuit in the Manifold Flow Valve harness connector.
4. Turn the ignition on.
5. With the scan tool, read the Manifold Flow Valve signal voltage.
  Is the voltage above 4.5 volts with the jumper wire in place?
  
  Yes
  - Replace the Manifold Flow Valve in accordance with the Service Information.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Go to step 10
POWERTRAIN CONTROL MODULE (PCM)
1. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Manifold Flow Valve and the Powertrain Control Module (PCM).
2. Look for any chafed, pierced, pinched, or partially broken wires.
3. Look for broken, bent, pushed out or corroded terminals.
4. Monitor the scan tool data relative to this circuit and wiggle test the wiring and connectors.
5. Look for the data to change or for the DTC to reset during the wiggle test.
6. Refer to any Technical Service Bulletins that may apply.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .
  No
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information.
  - Perform the PCM VERIFICATION TEST. See DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard Procedure .