LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Jeep >> 2012 >> Wrangler Rubicon, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 95 (Electronic Control Modules (Service Information)) >> Module, Anti-Lock Brake System >> Installation >> Left-Hand Drive
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Left-Hand Drive

WARNING: This page is about a different car, the 2016 Dodge Journey and 2015 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.
  1. Clean any debris off the mating surfaces of the HCU and ABM.
    CAUTION:

    When installing new O-rings or solenoid valve stem seals, do not use any type of lubricant.

    Fig 1: Solenoid Valve Seal
    GC0124493Courtesy of CHRYSLER GROUP, LLC
    1 - SEAL
    2 - SOLENOID VALVE STEM
  2. If the seals (1) on the solenoid valve stems (2) are not new, replace them all. Each of the solenoid valve stem seals must be new to keep out moisture and debris;do not reuse solenoid valve stem seals. 
    Fig 2: Internal Pump Connector O-Ring
    GC0124494Courtesy of CHRYSLER GROUP, LLC
    1 - O-RING
    2 - O-RING MOUNTING GROOVE
  3. Replace the pump/motor connector O-ring (1) if it is not new. Be sure the O-ring is properly seated in the mounting groove (2).
    Fig 3: ABM, HCU & Solenoid Valve Stems
    GC0081324Courtesy of CHRYSLER GROUP, LLC
    1 - ABM
    2 - HCU
    3 - SOLENOID VALVE STEM
  4. Align components and install the ABM (1) on the HCU (2).
    Fig 4: ABM Mounting
    GC0128570Courtesy of CHRYSLER GROUP, LLC
  5. Install the four screws (1) attaching the ABM (2) to the HCU. Tighten the mounting screws to 2 N.m (17 in. lbs.).
    Fig 5: Anti-Lock Brake Module Wiring Harness Connector
    GC0081322Courtesy of CHRYSLER GROUP, LLC
    1 - ABM (PART OF ICU)
    2 - WIRING HARNESS CONNECTOR
    CAUTION:

    Before installing the ABM harness connector on the ABM, be sure the seal is properly installed in the connector.

  6. Insert the ABM wiring harness connector (2) into the socket of the ABM (1) and close the cover, locking the connector in place.
  7. Raise and support the vehicle. Refer to HOISTING, STANDARD PROCEDURE .
    Fig 6: ICU Mounting
    GC0082347Courtesy of CHRYSLER GROUP, LLC
  8. Loosen the two mounting screws (2) as necessary and allow the ICU (1) mounting bracket to slide down over the mounting screws and hang the assembly in place. Tighten the two mounting screws (2) to 23 N.m (17 ft. lbs.).
  9. Lower the vehicle.
  10. Position the fresh air plenum and install the two mounting screws.
    Fig 7: Wheelhouse Brace
    GC0128486Courtesy of CHRYSLER GROUP, LLC
  11. Install the wheelhouse brace (2). Install and tighten the eight mounting bolts (four each side) (1) to 48 N.m (35 ft. lbs.).
    Fig 8: Cowl Screen
    GC0128455Courtesy of CHRYSLER GROUP, LLC
  12. Install the cowl screen. Install the push-pins (1) securing the cowl screen to the wheelhouse brace and cowl. Rotate the screw (2) in the center of the cowl screen 90° counterclockwise to lock the screen in place.
  13. Install the wiper arms. Refer to ARM, WIPER, INSTALLATION .
    Fig 9: Cowl Top Screen
    GC0128454Courtesy of CHRYSLER GROUP, LLC
  14. Install the cowl top screen (3). Install the two push-pins (1) securing the cowl top screen at the ends. Install the remaining push-pins (2).
  15. Install the engine appearance cover.
  16. Connect the negative cable on the battery negative post.
  17. Hook up the scan tool to initialize the ABM and perform the following:
    1. Clear any faults.
    2. Perform the ABS Verification Test and road test the vehicle. Refer to STANDARD PROCEDURE .
scientia non olet · About LEMON Manuals