Right MULTIFUNCTION Switch: Operation: Operation

The right (wiper) multi-function switch uses a combination of resistor multiplexing and conventional analog switching to control the many functions and features it provides. The switch receives a clean ground from the Steering Control Module (SCM), then provides resistor multiplexed and conventional analog return outputs to the SCM to indicate the selected switch positions. The SCM then sends electronic switch status  messages over a Local Interface Network (LIN) data bus to the ElectroMechanical Instrument Cluster (EMIC) (also known as the Cab Compartment Node/CCN), and the EMIC relays electronic wiper  and washer switch  request messages over the Controller Area Network (CAN) data bus to other electronic modules in the vehicle.

If the SCM detects no inputs from the right multi-function switch, it transmits an electronic Signal Not Available (SNA)  status message over the LIN data bus. The SNA status signals the EMIC to request other electronic modules to implement a fail-safe mode of operation for the front and rear wiper systems. The fail-safe mode will maintain the last selected front and rear wiper system operation for the remainder of the current ignition cycle, after which both wiper systems will default to OFF.

The right multi-function switch as well as the hard wired inputs and outputs of the switch may be diagnosed using conventional diagnostic tools and procedures. Refer to the appropriate wiring information. However, the most reliable, efficient and accurate means to diagnose this component requires the use of a diagnostic scan tool. Refer to the appropriate diagnostic information.

Following are descriptions of how the right multi-function switch is operated to control the many front and rear wiper and washer system functions and features it provides:

• Front Wiper Control  - The control knob on the end of the right multi-function switch control stalk is rotated to one of the two continuous wiper detents, to one of five intermittent wiper detents, or to the OFF position to select the front wiper mode. The SCM reads the input from the right multi-function switch and sends electronic wiper switch  status messages over the LIN data bus to the EMIC, which relays an electronic wiper switch  request message over the CAN data bus to other electronic modules in the vehicle.
• Front Wiper Mist Mode  - The front wiper mist mode is requested when the right multi-function switch control stalk is depressed downward towards the floor to a momentary MIST position. The front wiper motor will continue to operate, one complete cycle at a time, for as long as the control stalk is held in this position. The SCM reads the resistor multiplexed input from the right multi-function switch and sends an electronic wiper switch  status message over the LIN data bus to the EMIC, which relays an electronic wiper switch  request message over the CAN data bus to other electronic modules in the vehicle.
• Front Washer Control  - The right multi-function switch control stalk is pulled rearward towards the steering wheel to a momentary WASH position to activate the washer pump/motor in the front washer mode. The washer pump/motor will continue to operate for as long as the control stalk is held in this position. The SCM reads the resistor multiplexed input from the right multi-function switch and sends an electronic washer switch  status message over the LIN data bus to the EMIC, which relays an electronic washer switch  request message over the CAN data bus to other electronic modules in the vehicle.
• Rear Wiper Control  - The rear wiper mode is selected when the right multi-function switch control sleeve is rotated to the fixed interval intermittent rear wipe detent position, or the OFF detent position. The SCM reads the input from the right multi-function switch and sends an electronic wiper switch  status message over the LIN data bus to the EMIC, which relays an electronic wiper switch  request message over the CAN data bus to other electronic modules in the vehicle.
• Rear Washer Control  - The right multi-function switch control sleeve is rotated to one of two momentary WASH positions, either fully forward or fully rearward, to activate the washer pump/motor in the rear washer mode. The washer pump/motor will continue to operate in the rear washer mode until the control sleeve is released. The SCM reads the input from the right multi-function switch and sends an electronic washer switch  status message over the LIN data bus to the EMIC, which relays an electronic washer switch  request message over the CAN data bus to other electronic modules in the vehicle.