LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Jeep >> 2017 >> Wrangler Rubicon, Automatic Trans >> Repair and Diagnosis (Single Page) >> Restraints >> Restraints Control Systems >> (Occupant Restraint Controller (Orc) - Electrical Diagnostics) >> DTC Troubleshooting >> B1B95-Passenger Seat Track Position Sensor Circuit Open >> Diagnostic Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Test

  1. CHECK FOR ACTIVE INTERNAL FAULTS, IGNITION FAULTS, AND BATTERY FAULTS IN THE OCCUPANT RESTRAINT CONTROLLER (ORC) 
    1. With the scan tool, read Occupant Restraint Controller (ORC) DTCs.

      Does the scan tool display any active DTCs relating to internal faults, ignition faults, or battery faults?

      Yes 

      No 

      • Go To  2
  2. VERIFY THAT DTC B1B95-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT OPEN IS ACTIVE 

    Does the scan tool display active: B1B95-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT OPEN?

    Yes 

    • Go To  3

    No 

  3. INSPECT PASSENGER SEAT HARNESS WIRES AND CONNECTORS 
    WARNING:

    Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    1. Using the wiring diagram/schematic as a guide, inspect the Passenger Seat Harness wiring and connectors. Look for chafed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or contaminated terminals.

      Are any of these conditions present?

      Yes 

      NOTE:

      Do not attempt to repair the Seat Harness. Replace the Seat Harness if any of these conditions exist

      • Replace the Passenger Seat Harness in accordance with the Service Information.
      • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to AIRBAG SYSTEM VERIFICATION TEST .

      No 

      • Go To  4
  4. VERIFY THAT PASSENGER SEAT HARNESS IS ROUTED CORRECTLY 
    1. Verify that the Passenger Seat Harness is routed correctly.

      Is the Passenger Seat Harness routed correctly?

      Yes 

      • Go To  5

      No 

  5. CHECK (R262) PASSENGER SEAT POSITION SENSOR DATA CIRCUIT AND (R264) PASSENGER SEAT POSITION SENSOR VOLTAGE CIRCUIT FOR AN OPEN 
    GC0149356Courtesy of CHRYSLER GROUP, LLC
    1. Disconnect the ORC harness connectors.
    2. Connect the SRS Load Tool Adapter (special tool #8443-32-L, Adapter, SRS Adapter) or (special tool #8443-32-R, Adapter, SRS Adapter) to the ORC harness connector.
    3. Measure the resistance of the (R262) Passenger Seat Position Sensor Data circuit between the appropriate terminal SRS Load Tool Adapter (special tool #8443-32-L, Adapter, SRS Adapter) or (special tool #8443-32-R, Adapter, SRS Adapter) and the Passenger Seat Track Position Sensor connector.
    4. Measure the resistance of the (R264) Passenger Seat Position Sensor Voltage circuit between the appropriate terminal of the SRS Load Tool Adapter (special tool #8443-32-L, Adapter, SRS Adapter) or (special tool #8443-32-R, Adapter, SRS Adapter) and the Passenger Seat Track Position Sensor connector.

      Is the resistance of either circuit above 5.0 Ohms?

      Yes 

      NOTE:

      Do not attempt to repair the Seat Harness. Replace the Seat Harness if the condition inspecting or testing for is present in the Seat Harness.

      • Replace the Passenger Seat Harness in accordance with the Service Information.
      • Perform the AIRBAG SYSTEM VERIFICATION TEST. Refer to AIRBAG SYSTEM VERIFICATION TEST .

      No 

      • Go To  6
  6. CHECK OPERATION OF THE PASSENGER SEAT TRACK POSITION SENSOR 
    1. Replace the Passenger Seat Track Position Sensor in accordance with the Service Information. Refer to SENSOR, SEAT TRACK POSITION .
    2. Reconnect the vehicle body harness to the Seat Track Position Sensor.
    3. Remove any special tools or jumper wires and reconnect all previously disconnected components - except the Battery.
      WARNING:

      Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

    4. Connect the scan tool to the Data Link Connector - use the most current software available.
    5. Use the scan tool and erase the stored codes in all airbag system modules.
    6. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
    7. Wait one minute, and read active codes and if there are none present read the stored codes.

      Did the active Passenger Seat Track Position Sensor DTC return?

      Yes 

      WARNING:

      If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to follow these instructions may result in possible serious or fatal injury.

      WARNING:

      Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

      No 

scientia non olet · About LEMON Manuals