Diagnostic Test

WARNING: This page is about a different car, the 2021 Jeep Grand Cherokee L. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FOR ANY SERVICE BULLETINS OR MODULE SOFTWARE UPDATES
1. Check for any applicable Service Bulletins or Flash updates related to the DTC.
  Are there any applicable Service Bulletins or Flash updates?
  
  Yes
  - Perform the applicable repair.
  - Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to POWER SEAT SYSTEM VERIFICATION TEST .
  No
  - Go To 2
READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
3. With the scan tool, erase all DTCs.
4. Turn the ignition off for a minimum of 10.0 seconds.
5. Turn the ignition on.
6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
7. With the scan tool, read DTCs.
Did the DTC return?

Yes
- Go To 3
No
- Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK FOR MSMD DTCS
1. Refer to the recorded DTCs.
  Are there any driver circuit or position sense MSMD DTCs present?
  
  Yes
  - Perform the applicable diagnostic procedure(s). Refer to DIAGNOSTIC CODE INDEX .
  No
  - Go To 4
CHECK THE DRIVER SEAT HORIZONTAL TRACK
1. Turn the ignition off.
2. Check the Driver Seat Horizontal Track for damage or obstructions.
  Were any issues found with the Driver Seat Horizontal Track?
  
  Yes
  - Repair the found issues in accordance with the Service Information.
  - Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to POWER SEAT SYSTEM VERIFICATION TEST .
  No
  - Go To 5
PERFORM THE MSMD STANDARDIZATION ROUTINE
1. With scan tool, perform the Memory Seat Module-Driver Standardization Routine.
2. With the scan tool, erase all DTCs.
3. Turn the ignition off for a minimum of 10.0 seconds.
4. Turn the ignition on.
5. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
6. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 6
  No
  - Performing the Standardization Routine repaired the fault.
  - Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to POWER SEAT SYSTEM VERIFICATION TEST .
CHECK RELATED MSMD AND COMPONENT HARNESS CONNECTIONS
1. Turn the ignition off.
2. Disconnect all MSMD harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all MSMD harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
11. With the scan tool, read MSMD DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Memory Seat Module-Driver (MSMD) in accordance with the Service Information. Refer to MODULE, MEMORY SEAT (MSM), REMOVAL AND INSTALLATION .
  - Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to POWER SEAT SYSTEM VERIFICATION TEST .
  No
  - The wiring or poor connection has been repaired.
  - Perform the POWER SEAT SYSTEM VERIFICATION TEST. Refer to POWER SEAT SYSTEM VERIFICATION TEST .