LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Jeep >> 2024 >> Gladiator Nighthawk, Part Time T/Case Control, Automatic Trans >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Drivers Assistance System Module - DTCS B1EAD-2A To C2318-4B >> DTC Troubleshooting >> C00C1-13 Front Radar Module "B" - Circuit Open >> Diagnostic Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Test

  1. CHECK FOR ANY SERVICE BULLETINS OR MODULE SOFTWARE UPDATES 
    1. Check for any applicable Service Bulletins or Flash updates related to the DTC.

      Are there any applicable Service Bulletins or Flash updates?

      Yes 

      No 

      • Go To  2
  2. READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN 
    1. With the scan tool, read DTCs in all Electronic Control Units (ECU's) and record on the repair order.
    2. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
    3. With the scan tool, erase all DTCs.
    4. Turn the ignition off for a minimum of 10.0 seconds.
    5. Turn the ignition on.
    6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    7. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Go To  3

      No 

  3. CHECK FOR PCM BATTERY OR CHARGING SYSTEM DTCS 
    1. Refer to the recorded DTCs.

      Are there any PCM battery OR charging system DTCs present?

      Yes 

      No 

      • Go To  4
  4. CHECK THE DASM PLUS THE IN-LINE AND RADAR HARNESS CONNECTORS AND TERMINALS 
    1. Turn the ignition off.
      NOTE:

      Most common areas of concern are the DASM, fascia in-line, and Radar connections.

    2. Check the harness connectors for proper connection at the DASM, fascia in-line connection, and the Radar connection.
    3. Verify that the connector is completely plugged in and locked prior to disconnecting.
    4. Disconnect the DASM, fascia in-line connection, and the Radar harness connectors and check for pushed out or spread terminals, brinelling on terminals, discoloration from excessive heat, or corrosion and water intrusion.

      Were any issues found with the connectors or terminals?

      Yes 

      No 

      • Go To  5
  5. ISOLATE AND CHECK THE FRONT LONG RANGE RADAR (P565) POWER SUPPLY CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. The ignition must be off when checking the continuity of a circuit.
    2. Isolate the circuit by disconnecting the Electronic Control Unit (ECU) and the component harness connector containing the circuit being tested. Note:  Use the wiring diagram as a guide to follow the path of the circuit.
    3. Before measuring the resistance of any circuit, first measure the resistance between the two leads of the DVOM. Note:  The meter leads can add resistance to the measurement value.
    4. Connect one lead of the DVOM to the circuit being tested at the component harness connector.
    5. Connect the other lead to the circuit being tested at the ECU harness connector and measure the resistance of the circuit.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Go To  6

      No 

  6. ISOLATE AND CHECK THE FRONT LONG RANGE RADAR (P566) RETURN CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. The ignition must be off when checking the continuity of a circuit.
    2. Isolate the circuit by disconnecting the Electronic Control Unit (ECU) and the component harness connector containing the circuit being tested. Note:  Use the wiring diagram as a guide to follow the path of the circuit.
    3. Before measuring the resistance of any circuit, first measure the resistance between the two leads of the DVOM. Note:  The meter leads can add resistance to the measurement value.
    4. Connect one lead of the DVOM to the circuit being tested at the component harness connector.
    5. Connect the other lead to the circuit being tested at the ECU harness connector and measure the resistance of the circuit.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Go To  7

      No 

  7. REPLACE THE FRONT LONG RANGE RADAR AND RETEST FOR DTCS 
    1. Turn the ignition off.
    2. Replace the Front Long Range Radar in accordance with the Service Information.
    3. Connect the component and Electronic Control Unit (ECU) harness connectors.
    4. Turn the ignition on.
    5. With the scan tool, erase all DTCs.
    6. Turn the ignition off for a minimum of 10.0 seconds.
    7. Turn the ignition on.
    8. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    9. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Go To  8

      No 

  8. CHECK RELATED DASM AND COMPONENT CONNECTIONS 
    1. Disconnect all DASM harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the related component harness connectors.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Perform a terminal drag test on each connector terminal to verify proper terminal tension.

      Repair any conditions that are found.

    5. Reconnect all DASM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    10. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      No 

scientia non olet · About LEMON Manuals