TCM Terminal Description
TCM TERMINAL DESCRIPTION
| Terminal No. | Item name | Description |
|---|---|---|
| 1 | PL-SOL | PL (Line pressure control) solenoid signal output |
| 2 | PVIGN | Solenoid drive power relay |
| 3 | PVIGN | Solenoid drive power relay |
| 4 | SEL3 | Data input signal for I/C (Input clutch) fluid pressure switch & SUB-ROM communication (double function) |
| 5 | GND-P | Ground(power) |
| 6 | CAN-H | CAN high |
| 7 | CAN-L | CAN low |
| 8 | ATF1 | Fluid temperature sensor 1 (Oil fan temperature) |
| 9 | BATT | Battery power |
| 10 | C1-SOL | I/C (Input Clutch) solenoid actuation output signal |
| 11 | C2-SOL | H&LR/C (High & low reverse clutch) solenoid output signal |
| 12 | VIGN-OUT | Control valve power |
| 13 | B3-ON/OFF SOL | LC/B (Low coast brake) solenoid actuation output signal |
| 14 | GND-P | Ground (power) |
| 15 | GND-A | Control valve ground (power) |
| 16 | SEL1 | Check sum signal for LC/B (Low coast brake) fluid pressure switch signal & SUB-ROM communication (double function) |
| 17 | ATF2 | Fluid temperature sensor 2 (T/CON out temperature) |
| 18 | PVIGNRLY | Solenoid power relay (control step) |
| 19 | B2-SOL | Fr/B (Front brake) solenoid output signal |
| 20 | L/U-SOL | L/U (Lock-up) solenoid output signal |
| 21 | C3-SOL | D/C (Direct clutch) solenoid output signal |
| 22 | SEL2 | System check signal during D/C (Direct Clutch) fluid pressure switch signal & SUB-ROM communication (double function) |
| 23 | K-LINE | K-line communication |
| 24 | GND-C | Ground (power) |
| 25 | - | - |
| 26 | PSC2 | H&LR/C (High & low reverse clutch) fluid pressure switch input signal |
| 27 | VSP1 | Vehicle speed sensor 1 (Output vehicle sensor) input signal |
| 28 | - | - |
| 29 | - | - |
| 30 | INHSW-1 | Inhibitor switch 1 input signal |
| 31 | INHSW-2 | Inhibitor switch 2 input signal |
| 32 | - | - |
| 33 | VIGN | VIGN power |
| 34 | - | - |
| 35 | PSB2 | Fr/B (Front brake) fluid pressure switch input signal |
| 36 | TURBIN1 | Turbine sensor 1 input signal (operate in 4th gear) |
| 37 | - | - |
| 38 | INHSW-3 | Inhibitor switch 3 input signal |
| 39 | INHSW-4 | Inhibitor switch 4 input signal |
| 40 | DATABIT 1 | Control valve communication line |
| 41 | REV-LAMP RLY | Reverse lamp relay output |
| 42 | VIGN | VIGN power |
| 43 | - | - |
| 44 | - | - |
| 45 | TURBIN 2 | Turbine sensor 2 input signal (operate in 1, 2, 3, 5th gears) |
| 46 | GND-C | Ground (power) |
| 47 | INH SW3-MON | Inhibitor switch 3 single monitor input signal |
| 48 | START RLY | Starter relay actuation output |
| 49 | P range LAMP | P range lamp output signal |
| 50 | Selected gear Display | Shift range display lamp output signal |
| 51 | N range LAMP | N range lamp output signal |
| 52 | 3 range LAMP | 3 range lamp output signal |
| 53 | STOP Lamp SW | Stop lamp switch input signal |
| 54 | Manual-up shift SW | Sports mode up shift switch input signal |
| 55 | Manual-down shift SW | Sports mode down shift switch input signal |
| 56 | - | - |
| 57 | O/D OFF SW | O/D (Over Drive) switch input signal |
| 58 | 2 range LAMP | 2 range lamp output signal |
| 59 | 1 range LAMP | 1 range lamp output signal |
| 60 | D range LAMP | D range lamp output signal |
| 61 | SNOW LAMP | Snow lamp output signal |
| 62 | O/D OFF LAMP | O/D OFF lamp output signal |
| 63 | Manual Mode select SW | Sports mode select switch input signal |
| 64 | - | - |
| 65 | ABS signal | Input ABS signal |
| 66 | L4 SW signal | Input L4 (4X4 LOW) switch signal |
| 67 | R range LAMP | R range LAMP output signal |
| 68 | P/N range signal | P/N range status output signal (SIGMA 3.5 engine only) |
| 69 | N range signal | P/N range status output signal (4WD only) |
| 70 | ACC SW signal | Auto cruise control SW input signal |
| 71 | - | - |
| 72 | SNOW SW | Snow mode switch input signal |