LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Land Rover >> 2010 >> LR2 >> Repair and Diagnosis (Single Page) >> Quick Lookups >> DTC Index >> DTC Index & General Information (1 Of 3) >> General Information >> Description And Operation >> Diagnostic Trouble Code (DTC) Index DTC: Audio Amplifier Module (AAM)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Trouble Code (DTC) Index DTC: Audio Amplifier Module (AAM)

NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures information , or determine if any prior approval program is in operation, before the replacement of a component.
NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).
NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places, and with an up-to-date calibration certificate. When testing resistance always take the resistance of the DMM leads into account.
NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.

Description And Operation 

For a detailed description of the audio amplifier system, refer to the relevant Description and Operation. Refer to Audio System .

AUDIO AMPLIFIER MODULE (AAM)

DTC Description Possible Cause Action
B1A01-11 Speaker #1
  • Front Left Tweeter Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Front Left Tweeter Speaker circuit for short to ground
B1A01-12 Speaker #1
  • Front Left Tweeter Speaker circuit - short to power
Refer to electrical circuit diagrams and check Front Left Tweeter Speaker circuit for short to power
B1A01-13 Speaker #1
  • Front Left Tweeter Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Front Left Tweeter Speaker circuit for open circuit
B1A01-1A Speaker #1
  • Front Left Tweeter Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Front left tweeter speaker connection for crossload
B1A01-49 Speaker #1
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A02-11 Speaker #2
  • Front Right Tweeter Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Front Right Tweeter Speaker circuit for short to ground
B1A02-12 Speaker #2
  • Front Right Tweeter Speaker circuit - short to power
Refer to electrical circuit diagrams and check Front Right Tweeter Speaker circuit for short to power
B1A02-13 Speaker #2
  • Front Right Tweeter Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Front Right Tweeter Speaker circuit for open circuit
B1A02-1A Speaker #2
  • Front Right Tweeter Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Front right tweeter speaker connection for crossload
B1A02-49 Speaker #2
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A03-11 Speaker #3
  • Front Left Woofer Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Front Left Woofer Speaker circuit for short to ground
B1A03-12 Speaker #3
  • Front Left Woofer Speaker circuit - short to power
Refer to electrical circuit diagrams and check Front Left Woofer Speaker circuit for short to power
B1A03-13 Speaker #3
  • Front Left Woofer Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Front Left Woofer Speaker circuit for open circuit
B1A03-1A Speaker #3
  • Front Left Woofer Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Front left woofer speaker connection for crossload
B1A03-49 Speaker #3
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A04-11 Speaker #4
  • Front Right Woofer Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Front Right Woofer Speaker circuit for short to ground
B1A04-12 Speaker #4
  • Front Right Woofer Speaker circuit - short to power
Refer to electrical circuit diagrams and check Front Right Woofer Speaker circuit for short to power
B1A04-13 Speaker #4
  • Front Right Woofer Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Front Right Woofer Speaker circuit for open circuit
B1A04-1A Speaker #4
  • Front Right Woofer Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Front right woofer speaker connection for crossload
B1A04-49 Speaker #4
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A05-11 Speaker #5
  • Rear Left Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Rear Left Speaker circuit for short to ground
B1A05-12 Speaker #5
  • Rear Left Speaker circuit - short to power
Refer to electrical circuit diagrams and check Rear Left Speaker circuit for short to power
B1A05-13 Speaker #5
  • Rear Left Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Rear Left Speaker circuit for open circuit
B1A05-1A Speaker #5
  • Rear Left Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Rear left speaker connection for crossload
B1A05-49 Speaker #5
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A06-11 Speaker #6
  • Rear Right Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Rear Right Speaker circuit for short to ground
B1A06-12 Speaker #6
  • Rear Right Speaker circuit - short to power
Refer to electrical circuit diagrams and check Rear Right Speaker circuit for short to power
B1A06-13 Speaker #6
  • Rear Right Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Rear Right Speaker circuit for open circuit
B1A06-1A Speaker #6
  • Rear Right Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Rear right speaker connection for crossload
B1A06-49 Speaker #6
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A07-11 Speaker #7
  • Rear Left Surround Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Rear Left Surround Speaker circuit for short to ground
B1A07-12 Speaker #7
  • Rear Left Surround Speaker circuit - short to power
Refer to electrical circuit diagrams and check Rear Left Surround Speaker circuit for short to power
B1A07-13 Speaker #7
  • Rear Left Surround Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Rear Left Surround Speaker circuit for open circuit
B1A07-1A Speaker #7
  • Rear Left Surround Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Rear left surround speaker connection for crossload
B1A07-49 Speaker #7
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A08-11 Speaker #8
  • Rear Right Surround Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Rear Right Surround Speaker circuit for short to ground
B1A08-12 Speaker #8
  • Rear Right Surround Speaker circuit - short to power
Refer to electrical circuit diagrams and check Rear Right Surround Speaker circuit for short to power
B1A08-13 Speaker #8
  • Rear Right Surround Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Rear Right Surround Speaker circuit for open circuit
B1A08-1A Speaker #8
  • Rear Right Surround Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Rear right surround speaker connection for crossload
B1A08-49 Speaker #8
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A09-11 Speaker #9
  • Center Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Center Speaker circuit for short to ground
B1A09-12 Speaker #9
  • Center Speaker circuit - short to power
Refer to electrical circuit diagrams and check Center Speaker circuit for short to power
B1A09-13 Speaker #9
  • Center Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Center Speaker circuit for open circuit
B1A09-1A Speaker #9
  • Center Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Center speaker connection for crossload
B1A09-49 Speaker #9
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A10-11 Speaker #10
  • Left Subwoofer Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Left Subwoofer Speaker circuit for short to ground
B1A10-12 Speaker #10
  • Left Subwoofer Speaker circuit - short to power
Refer to electrical circuit diagrams and check Left Subwoofer Speaker circuit for short to power
B1A10-13 Speaker #10
  • Left Subwoofer Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Left Subwoofer Speaker circuit for open circuit
B1A10-1A Speaker #10
  • Left Subwoofer Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Left subwoofer speaker connection for crossload
B1A10-49 Speaker #10
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1A11-11 Speaker #11
  • Right Subwoofer Speaker circuit - short to ground
Refer to electrical circuit diagrams and check Right Subwoofer Speaker circuit for short to ground
B1A11-12 Speaker #11
  • Right Subwoofer Speaker circuit - short to power
Refer to electrical circuit diagrams and check Right Subwoofer Speaker circuit for short to power
B1A11-13 Speaker #11
  • Right Subwoofer Speaker circuit - open circuit
Refer to electrical circuit diagrams and check Right Subwoofer Speaker circuit for open circuit
B1A11-1A Speaker #11
  • Right Subwoofer Speaker circuit - resistance below threshold
Refer to electrical circuit diagrams and check Right subwoofer speaker connection for crossload
B1A11-49 Speaker #11
  • Internal electronic failure
Install a new module, refer to the new module/component installation note at the top of the DTC Index
B1D84-11 Headphone panel 1
  • Headphone panel 1 left or right signal circuit - short to ground
Refer to electrical circuit diagrams and check headphone panel 1 left or right signal circuit for short to ground
B1D84-13 Headphone panel 1
  • Headphone panel 1 left or right signal circuit - open circuit
Refer to electrical circuit diagrams and check headphone panel 1 left or right signal circuit for open circuit
B1D84-23 Headphone panel 1
  • Headphone panel 1 control line circuit - signal stuck low
Refer to electrical circuit diagrams and check headphone panel 1 control line for short to ground. Check for stuck switch/button
B1D85-11 Headphone panel 2
  • Headphone panel 2 left or right signal circuit - short to ground
Refer to electrical circuit diagrams and check headphone panel 2 left or right signal circuit for short to ground
B1D85-13 Headphone panel 2
  • Headphone panel 2 left or right signal circuit - open circuit
Refer to electrical circuit diagrams and check headphone panel 2 left or right signal circuit for open circuit
B1D85-23 Headphone panel 2
  • Headphone panel 2 control line circuit - signal stuck low
Refer to electrical circuit diagrams and check headphone panel 2 control line for short to ground. Check for stuck switch/button
B1D86-11 Headphone panel 3
  • Headphone panel 3 left or right signal circuit - short to ground
Only 2 headphone panels available on this vehicle. If this DTC is logged, check/amend Car Configuration File to reflect 2 panels only using the manufacturer approved diagnostic system
B1D86-13 Headphone panel 3
  • Headphone panel 3 left or right signal circuit - open circuit
Only 2 headphone panels available on this vehicle. If this DTC is logged, check/amend Car Configuration File to reflect 2 panels only using the manufacturer approved diagnostic system
B1D86-23 Headphone panel 3
  • Headphone panel 3 control line circuit - signal stuck low
Only 2 headphone panels available on this vehicle. If this DTC is logged, check/amend Car Configuration File to reflect 2 panels only using the manufacturer approved diagnostic system
B1D87-11 Headphone panel 4
  • Headphone panel 4 left or right signal circuit - short to ground
Only 2 headphone panels available on this vehicle. If this DTC is logged, check/amend Car Configuration File to reflect 2 panels only using the manufacturer approved diagnostic system
B1D87-13 Headphone panel 4
  • Headphone panel 4 left or right signal circuit - open circuit
Only 2 headphone panels available on this vehicle. If this DTC is logged, check/amend Car Configuration File to reflect 2 panels only using the manufacturer approved diagnostic system
B1D87-23 Headphone panel 4
  • Headphone panel 4 control line circuit - signal stuck low
Only 2 headphone panels available on this vehicle. If this DTC is logged, check/amend Car Configuration File to reflect 2 panels only using the manufacturer approved diagnostic system
U3000-05 Control module - system programming failures
  • Software incompatibility
  • The version of the Local Configuration file does not match that expected
Re-configure the audio amplifier as an existing control module, using the manufacturer approved diagnostic system
U3000-42 Control module - general memory failure
  • General memory failure
Re-configure the audio amplifier as an existing control module, using the manufacturer approved diagnostic system. Clear DTC, cycle ignition and read DTCs. If DTC returns, suspect audio amplifier module and install a new module. Refer to the new module/component installation note at the top of the DTC Index
U3000-44 Control module - data memory failure
  • Data memory failure
Re-configure the audio amplifier as an existing control module, using the manufacturer approved diagnostic system. Clear DTC, cycle ignition and read DTCs. If DTC returns, suspect audio amplifier module and install a new module. Refer to the new module/component installation note at the top of the DTC Index
U3000-55 Control Module
  • Incorrect car configuration data received
Check/up-date Car Configuration File using manufacturer approved diagnostic system
U3000-87 Control Module
  • Missing message
Check CJB for DTCs and refer to DTC Index. Refer to Communications Network . Check information and entertainment module for Car Configuration File and MOST network DTCs and refer to relevant DTC Index. Carry out MOST/CAN network tests using the manufacturer approved diagnostic system
U3003-16 Battery Voltage
  • Circuit voltage below threshold
Carry out pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U3003-17 Battery Voltage
  • Circuit voltage above threshold
Carry out pinpoint tests associated with this DTC using the manufacturer approved diagnostic system