Diagnostic Trouble Code Index DTC: Transfer Case Control Module (TCCM) -- Range Rover/L405
- General Information
- Description And Operation
- Diagnostic Trouble Code Index - DTC: Transfer Case Control Module (TCCM) (G2016291)
- Transfer Case Control Module (TCCM)
- DTC P0605-41 Internal Control Module Read Only Memory (ROM) Error - General checksum failure
- DTC P0605-43 Internal Control Module Read Only Memory (ROM) Error - Special memory failure
- DTC P062F-43 Internal Control Module EEPROM Error - Special memory failure
- DTC P062F-68 Internal Control Module EEPROM Error - Event information
- DTC P0666-11 Control Module Internal Temperature Sensor "A" Circuit - Circuit short to ground
- DTC P0666-12 Control Module Internal Temperature Sensor "A" Circuit - Circuit short to battery
- DTC P0666-29 Control Module Internal Temperature Sensor "A" Circuit - Signal invalid
- DTC P0666-64 Control Module Internal Temperature Sensor "A" Circuit - Signal plausibility failure
- DTC P080A-56 Clutch Position Not Learned - Invalid/incomplete configuration
- DTC P0810-04 Clutch Position Control Error - System internal failures
- DTC P0810-07 Clutch Position Control Error - Mechanical failures
- DTC P0810-28 Clutch Position Control Error - Signal bias level out of range/zero adjustment failure
- DTC P0810-46 Clutch Position Control Error - Calibration/parameter memory failure
- DTC P0810-56 Clutch Position Control Error - Invalid/incomplete configuration
- DTC P0810-62 Clutch Position Control Error - Signal compare failure
- DTC P0810-77 Clutch Position Control Error - Commanded position not reachable
- DTC P0810-78 Clutch Position Control Error - Alignment or adjustment incorrect
- DTC P0919-94 Gear Shift Position Control Error - Unexpected operation
- DTC P160C-45 Control Module Software Performance - Program memory failure
- DTC P160C-48 Control Module Software Performance - Supervision software failure
- DTC P160C-94 Control Module Software Performance - Unexpected operation
- DTC P170E-07 Clutch Delivered Torque Performance - Mechanical failures
- DTC P170E-92 Clutch Delivered Torque Performance - Performance or incorrect operation
- DTC P175B-00 Transfer Case Clutch Deteriorated - No sub type information
- DTC P183A-67 Range Change Mechanism Failure - Signal incorrect after event
- DTC P183A-77 Range Change Mechanism Failure - Commanded position not reachable
- DTC P186D-71 Clutch Actuator Stuck - Actuator stuck
- DTC P18A4-13 Motion/Position Sensor Power Circuit - Circuit open
- DTC P18A4-16 Motion/Position Sensor Power Circuit - Circuit voltage below threshold
- DTC P18A4-17 Motion/Position Sensor Power Circuit - Circuit voltage above threshold
- DTC P18A5-03 Motion/Position Sensor A Signal Circuit - FM (Frequency Modulated)/PWM (Pulse Width Modulated) failures
- DTC P18A5-11 Motion/Position Sensor A Signal Circuit - Circuit short to ground
- DTC P18A5-12 Motion/Position Sensor A Signal Circuit - Circuit short to battery
- DTC P18A5-13 Motion/Position Sensor A Signal Circuit - Circuit open
- DTC P18A5-37 Motion/Position Sensor A Signal Circuit - Signal frequency too high
- DTC P18A5-62 Motion/Position Sensor A Signal Circuit - Signal compare failure
- DTC P215A-62 Vehicle Speed/Wheel Speed Correlation - Signal compare failure
- DTC P215A-64 Vehicle Speed/Wheel Speed Correlation - Signal plausibility failure
- DTC P2787-98 Clutch Temperature Too High - Component or system over temperature
- DTC U0080-81 Vehicle Communication Bus F - Invalid serial data received
- DTC U0080-82 Vehicle Communication Bus F - Alive/sequence counter incorrect/not updated
- DTC U0080-83 Vehicle Communication Bus F - Value of signal protection calculation incorrect
- DTC U0080-87 Vehicle Communication Bus F - Missing message
- DTC U0080-88 Vehicle Communication Bus F - Bus off
- DTC U1000-02 Solid State Driver Protection Active - Driver Disabled - General signal failure
- DTC U1000-11 Solid State Driver Protection Active - Driver Disabled - Circuit short to ground
- DTC U1000-12 Solid State Driver Protection Active - Driver Disabled - Circuit short to battery
- DTC U1000-16 Solid State Driver Protection Active - Driver Disabled - Circuit voltage below threshold
- DTC U1000-17 Solid State Driver Protection Active - Driver Disabled - Circuit voltage above threshold
- DTC U1000-1C Solid State Driver Protection Active - Driver Disabled - Circuit voltage out of range
- DTC U1000-49 Solid State Driver Protection Active - Driver Disabled - Internal electronic failure
- DTC U1000-4B Solid State Driver Protection Active - Driver Disabled - Over temperature
- DTC U1000-56 Solid State Driver Protection Active - Driver Disabled - Invalid/incomplete configuration
- DTC U1000-62 Solid State Driver Protection Active - Driver Disabled - Signal compare failure
- DTC U1A4B-04 Control Module Processor B - System internal failures
- DTC U1A4B-16 Control Module Processor B - Circuit voltage below threshold
- DTC U1A4B-17 Control Module Processor B - Circuit voltage above threshold
- DTC U1A4B-1C Control Module Processor B - Circuit voltage out of range
- DTC U1A4B-47 Control Module Processor B - Watchdog/safety microcontroller failure
- DTC U1A4B-48 Control Module Processor B - Supervision software failure
- DTC U1A4B-49 Control Module Processor B - Internal electronic failure
- DTC U1A4B-4B Control Module Processor B - Over temperature
- DTC U1A4B-55 Control Module Processor B - Not configured
- DTC U1A4B-56 Control Module Processor B - Invalid/incomplete configuration
- DTC U1A4B-64 Control Module Processor B - Signal plausibility failure
- DTC U1A4B-84 Control Module Processor B - Signal below allowable range
- DTC U1A4B-92 Control Module Processor B - Performance or incorrect operation
- DTC U1A4B-9A Control Module Processor B - Component or system operating conditions
- DTC U200C-4B Control Module Internal Power C - Over temperature
- DTC U200C-64 Control Module Internal Power C - Signal plausibility failure
- DTC U200C-9A Control Module Internal Power C - Component or system operating conditions
- DTC U2011-16 Motor - Circuit voltage below threshold
- DTC U2011-17 Motor - Circuit voltage above threshold
- DTC U2011-18 Motor - Circuit current below threshold
- DTC U2011-19 Motor - Circuit current above threshold
- DTC U2011-1D Motor - Circuit current out of range
- DTC U2011-28 Motor - Signal bias level out of range/zero adjustment failure
- DTC U2011-41 Motor - General checksum failure
- DTC U2011-4B Motor - Over temperature
- DTC U2011-56 Motor - Invalid/incomplete configuration
- DTC U2011-62 Motor - Signal compare failure
- DTC U2011-68 Motor - Event information
- DTC U2011-77 Motor - Commanded position not reachable
- DTC U2011-78 Motor - Alignment or adjustment incorrect
- DTC U2011-85 Motor - Signal above allowable range
- DTC U2011-86 Motor - Signal invalid
- DTC U2011-98 Motor - Component or system over temperature
- DTC U2011-9A Motor - Component or system operating conditions
- DTC U2016-04 Control Module Main Software - System internal failures
- DTC U2016-06 Control Module Main Software - Algorithm based failures
- DTC U2016-47 Control Module Main Software - Watchdog/safety microcontroller failure
- DTC U2016-49 Control Module Main Software - Internal electronic failure
- DTC U2016-92 Control Module Main Software - Performance or incorrect operation
- DTC U201A-54 Control Module Main Calibration Data - Missing calibration
- DTC U2100-54 Initial Configuration Not Complete - Missing calibration
- DTC U2101-56 Control Module Configuration Incompatible - Invalid/incomplete configuration
- DTC U2300-54 Central Configuration - Missing calibration
- DTC U2300-55 Central Configuration - Not configured
- DTC U2300-56 Central Configuration - Invalid/incomplete configuration
- DTC U2300-64 Central Configuration - Signal plausibility failure
- DTC U3000-1C Control Module - Circuit voltage out of range
- DTC U3000-42 Control Module - General memory failure
- DTC U3000-4A Control Module - Incorrect component installed
- DTC U3000-4B Control Module - Over temperature
- DTC U3000-92 Control Module - Performance or incorrect operation
- DTC U3000-94 Control Module - Unexpected operation
- DTC U3000-98 Control Module - Component or system over temperature
- DTC U3006-13 Control Module Input Power "A" - Circuit open
- DTC U3006-16 Control Module Input Power "A" - Circuit voltage below threshold
- DTC U3006-17 Control Module Input Power "A" - Circuit voltage above threshold
- DTC U3006-85 Control Module Input Power "A" - Signal above allowable range
- DTC U3012-04 Control Module Improper Wake-up Performance - System internal failures
- DTC U3012-1C Control Module Improper Wake-up Performance - Circuit voltage out of range
- DTC U3012-41 Control Module Improper Wake-up Performance - General checksum failure
- DTC U3012-48 Control Module Improper Wake-up Performance - Supervision software failure
- DTC U3012-92 Control Module Improper Wake-up Performance - Performance or incorrect operation
- DTC U3012-94 Control Module Improper Wake-up Performance - Unexpected operation
- DTC U3012-96 Control Module Improper Wake-up Performance - Component internal failure
- Diagnostic Trouble Code Index - DTC: Transfer Case Control Module (TCCM) (G2016291)
- Description And Operation