Rear View Camera (RVC)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.

NOTE:

Guided Diagnostics must be followed and the repair advised by the process completed. Failure to do so may result in the rejection of any warranty claim made.
If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual, or determine if any prior approval program is in operation, prior to the installation of a new module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the Jaguar Land Rover approved diagnostic equipment).
When performing voltage or resistance tests, always use a digital multimeter that has the resolution ability to view 3 decimal places. For example, on the 2 volts range can measure 1 mV or 2 K Ohm range can measure 1 Ohm. When testing resistance always take the resistance of the digital multimeter leads into account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
Check JLR claims submission system for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific customer complaint and carry out the recommendations as required.

The DTC Index lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Rear View Camera (RVC). For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing service information. For additional information, Refer to: PARKING AID

DTC	DESCRIPTION	POSSIBLE CAUSES	ACTION
B100E-29	Video Input "A" - Signal invalid	LVDS circuit(s) short circuit to ground, short circuit to power, short circuit together, open circuit, high resistance	Refer to the electrical circuit diagrams and check the LVDS circuit(s) for short circuit to ground, short circuit to power, short circuit together, open circuit, high resistance. Replace LVDS cables as required, clear DTC and retest
B14AD-31	Front Display Screen - No signal	Touchscreen fault	Using the Jaguar Land Rover approved diagnostic equipment, check the touchscreen for related DTCs and refer to the relevant DTC index
U0001-88	High Speed CAN Communication Bus - Bus off	High speed CAN bus (comfort) circuit short circuit to ground, short circuit to power, open circuit, high resistance	Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the electrical circuit diagrams and check the high speed CAN bus (comfort) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest
U0002-81	High Speed CAN Communication Bus Performance - Invalid serial data received	Invalid data received from another control module via the high speed CAN bus (comfort)	Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0002-87	High Speed CAN Communication Bus Performance - Missing message	Missing message from another control module via the high speed CAN bus (comfort)	Using the Jaguar Land Rover approved diagnostic equipment, check the gateway module for related DTCs and refer to the relevant DTC index
U0300-00	Internal Control Module Software Incompatibility - No sub type information	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest
U0400-29	Invalid Data Received - Signal invalid	Missing/invalid data from the infotainment master controller Missing/invalid data from the anti-lock brake system control module Missing/invalid data from the steering angle sensor module	Using the Jaguar Land Rover approved diagnostic equipment, check the infotainment master controller for related DTCs and refer to the relevant DTC index Using the Jaguar Land Rover approved diagnostic equipment, check the anti-lock brake system control module for related DTCs and refer to the relevant DTC index Using the Jaguar Land Rover approved diagnostic equipment, check the steering angle sensor module for related DTCs and refer to the relevant DTC index
U0447-29	Invalid Data Received From Gateway A - Signal invalid	Missing/invalid data from the gateway module	Using the Jaguar Land Rover approved diagnostic equipment, check the gateway module for related DTCs and refer to the relevant DTC index
U0494-29	Invalid Data Received From Digital Audio Control Module A - Signal invalid	Missing/invalid data from the infotainment master controller	Using the Jaguar Land Rover approved diagnostic equipment, check the infotainment master controller for related DTCs and refer to the relevant DTC index
U0533-29	Invalid Data Received From Side Obstacle Detection Control Module - Left - Signal invalid	Missing/invalid data from the left blindspot monitoring control module	Using the Jaguar Land Rover approved diagnostic equipment, check the left blindspot monitoring control module for related DTCs and refer to the relevant DTC index
U0534-29	Invalid Data Received From Side Obstacle Detection Control Module - Right - Signal invalid	Missing/invalid data from the right blindspot monitoring control module	Using the Jaguar Land Rover approved diagnostic equipment, check the right blindspot monitoring control module for related DTCs and refer to the relevant DTC index
U1A14-00	CAN Initialization Failure - No sub type information	Rear view camera - Internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear view camera
U1A4B-49	Control Module Processor B - Internal electronic failure	Rear view camera - Internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear view camera
U201A-51	Control Module Main Calibration Data - Not programmed	Rear view camera is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear view camera
U201B-54	Control Module Calibration Data #2 - Missing calibration	Rear view camera is unable to calibrate Damage to rear view camera or camera mounting	Check the rear view camera for signs of damage or surrounding damage to mountings. If damage is evident replace parts as required If no damage is evident, clear DTC and retest. If fault persists, replace the rear view camera
U2023-41	Control Module Network Signal Calibration Data - General checksum failure	Car configuration file mismatch with vehicle specification Rear view camera is not configured correctly	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the rear view camera with the latest level software
U2300-55	Central Configuration - Not configured	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest
U2300-56	Central Configuration - Invalid/incomplete configuration	Rear view camera is not configured correctly	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the rear view camera with the latest level software
U2300-64	Central Configuration - Signal plausibility failure	Car configuration file mismatch with vehicle specification Rear view camera is not configured correctly Incorrect touchscreen fitted	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the rear view camera with the latest level software Check that the correct touchscreen is installed and rectify as required
U3000-08	Control Module - Bus signal/message failures	Rear view camera internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear view camera
U3000-16	Control Module - Circuit voltage below threshold	Rear view camera power or ground circuit open circuit, high resistance Battery/charging system fault	Refer to the electrical circuit diagrams and check the rear view camera power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Refer to the relevant service information and test the battery and charging system
U3000-17	Control Module - Circuit voltage above threshold	Battery/charging system fault	Refer to the relevant service information and test the battery and charging system
U3000-49	Control Module - Internal electronic failure	Rear view camera internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear view camera
U3000-92	Control Module - Performance or incorrect operation	Rear view camera internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear view camera
U3000-98	Control Module - Component or system over temperature	Rear view camera internal temperature above threshold	Allow the vehicle to cool. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear view camera