LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Land Rover >> 2019 >> Range Rover Velar Base >> Repair and Diagnosis (Single Page) >> Quick Lookups >> DTC Index >> Diagnostic Trouble Code Index DTC: Anti-Lock Brake System (Abs) -- Range Rover Velar/L560 >> General Information >> Description And Operation >> Diagnostic Trouble Code Index - DTC: Anti-Lock Brake System Control Module (Abs) (G2016176) >> Anti-Lock Brake System Control Module (Abs)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Anti-Lock Brake System Control Module (Abs)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT  acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTE:
  • Guided Diagnostics must be followed and the repair advised by the process completed. Failure to do so may result in the rejection of any warranty claim made.
  • If the control module or a component is at fault and the vehicle remains under manufacturer warranty, refer to the warranty policy and procedures manual, or determine if any prior approval program is in operation, prior to the installation of a new module/component.
  • Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the Jaguar Land Rover Approved Diagnostic Equipment).
  • When performing voltage or resistance tests, always use a digital multimeter that has the resolution ability to view 3 decimal places. For example, on the 2 volts range can measure 1 mV or 2 K Ohm range can measure 1 Ohm. When testing resistance always take the resistance of the digital multimeter leads into account.
  • Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
  • Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
  • If Diagnostic Trouble Code(s) are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
  • Check JLR claims submission system for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific customer complaint and complete the recommendations as required.

The DTC Index lists all Diagnostic Trouble Codes (Diagnostic Trouble Code(s)) that could be set in the Anti-Lock Brake System Control Module (ABS). For additional diagnosis and testing information, refer to the relevant Description and Operation in the service information. For additional information, Refer to: ANTI-LOCK CONTROL - STABILITY ASSIST (206-09 Anti-Lock Control - Stability Assist, Diagnosis and Testing)/PARKING BRAKE (206-05 Parking Brake and Actuation, Diagnosis and Testing).

DTC DESCRIPTION POSSIBLE CAUSES ACTION
B1111-86 Electric Park Brake Enable - Signal invalid
  • Electric park brake switch circuits short circuit to ground, short circuit to power, open circuit, high resistance
  • Electric park brake left or right actuator circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Refer to the electrical circuit diagrams and check the electric park brake switch circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the electric park brake left and right actuator circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
C0030-38 Left Front Tone Wheel - Signal frequency incorrect
  • Front left wheel speed sensor not securely mounted
  • Front left wheel speed sensor magnetic reluctor ring damaged
  • Front left wheel bearing failure
  • Front left wheel/tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the front left wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the front left wheel speed sensor magnetic reluctor ring. Rectify as required
  • Check the front left wheel bearing. Rectify as required
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the front left wheel and tire for condition and balance. Check and tighten the wheel nuts
C0031-11 Left Front Wheel Speed Sensor - Circuit short to ground
  • Front left wheel speed sensor power circuit short circuit to ground
  • Front left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor as required
C0031-12 Left Front Wheel Speed Sensor - Circuit short to battery
  • Front left wheel speed sensor power circuit short circuit to power
  • Front left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to power. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor as required
C0031-14 Left Front Wheel Speed Sensor - Circuit short to ground or open
  • Front left wheel speed sensor signal circuit short circuit to ground, open circuit, high resistance
  • Front left wheel speed sensor power circuit open circuit, high resistance
  • Front left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, open circuit, high resistance. Repair the circuit as required. Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - Left Front Wheel Speed Sensor Input (2B06)
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor as required
C0031-1C Left Front Wheel Speed Sensor - Circuit voltage out of range
  • Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor power circuit short circuit to another wheel speed sensor circuit
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to another wheel speed sensor circuit. Repair the circuit as required
C0031-25 Left Front Wheel Speed Sensor - Signal shape/waveform failure
  • Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor as required
C0031-29 Left Front Wheel Speed Sensor - Signal invalid
  • Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor as required
C0031-2F Left Front Wheel Speed Sensor - Signal erratic
  • Front left wheel speed sensor not securely mounted
  • Front left wheel speed sensor magnetic reluctor ring damaged
  • Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the front left wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the front left wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor as required
C0031-31 Left Front Wheel Speed Sensor - No signal
  • Front left wheel speed sensor not securely mounted
  • Front left wheel speed sensor magnetic reluctor ring damaged
  • Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the front left wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the front left wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor as required
C0031-4A Left Front Wheel Speed Sensor - Incorrect component installed
  • Incorrect front left wheel speed sensor installed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor of the correct specification as required
C0031-62 Left Front Wheel Speed Sensor - Signal compare failure
  • Front left wheel speed sensor not securely mounted
  • Front left wheel speed sensor magnetic reluctor ring damaged
  • Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the front left wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the front left wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front left wheel speed sensor as required
C0031-66 Left Front Wheel Speed Sensor - Signal has too many transitions/events
  • Front left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front left wheel/tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the front left wheel and tire for condition and balance. Check and tighten the wheel nuts
C0031-76 Left Front Wheel Speed Sensor - Wrong mounting position
  • Front left wheel speed sensor incorrectly installed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check the integrity and positioning of the front left wheel speed sensor mounting and rectify as required
C0033-38 Right Front Tone Wheel - Signal frequency incorrect
  • Front right wheel speed sensor not securely mounted
  • Front right wheel speed sensor magnetic reluctor ring damaged
  • Front right wheel bearing failure
  • Front right wheel/tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the front right wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the front right wheel speed sensor magnetic reluctor ring. Rectify as required
  • Check the front right wheel bearing. Rectify as required
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the front right wheel and tire for condition and balance. Check and tighten the wheel nuts
C0034-11 Right Front Wheel Speed Sensor - Circuit short to ground
  • Front right wheel speed sensor power circuit short circuit to ground
  • Front right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor as required
C0034-12 Right Front Wheel Speed Sensor - Circuit short to battery
  • Front right wheel speed sensor power circuit short circuit to power
  • Front right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to power. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor as required
C0034-14 Right Front Wheel Speed Sensor - Circuit short to ground or open
  • Front right wheel speed sensor signal circuit short circuit to ground, open circuit, high resistance
  • Front right wheel speed sensor power circuit open circuit, high resistance
  • Front right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, open circuit, high resistance. Repair the circuit as required. Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - Right Front Wheel Speed Sensor Input (2B07)
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor as required
C0034-1C Right Front Wheel Speed Sensor - Circuit voltage out of range
  • Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor power circuit short circuit to another wheel speed sensor circuit
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to another wheel speed sensor circuit. Repair the circuit as required
C0034-25 Right Front Wheel Speed Sensor - Signal shape/waveform failure
  • Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor as required
C0034-29 Right Front Wheel Speed Sensor - Signal invalid
  • Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor as required
C0034-2F Right Front Wheel Speed Sensor - Signal erratic
  • Front right wheel speed sensor not securely mounted
  • Front right wheel speed sensor magnetic reluctor ring damaged
  • Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the front right wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the front right wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor as required
C0034-31 Right Front Wheel Speed Sensor - No signal
  • Front right wheel speed sensor not securely mounted
  • Front right wheel speed sensor magnetic reluctor ring damaged
  • Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the front right wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the front right wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor as required
C0034-4A Right Front Wheel Speed Sensor - Incorrect component installed
  • Incorrect front right wheel speed sensor installed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor of the correct specification as required
C0034-62 Right Front Wheel Speed Sensor - Signal compare failure
  • Front right wheel speed sensor not securely mounted
  • Front right wheel speed sensor magnetic reluctor ring damaged
  • Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the front right wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the front right wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new front right wheel speed sensor as required
C0034-66 Right Front Wheel Speed Sensor - Signal has too many transitions/events
  • Front right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Front right wheel/tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the front right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the front right wheel and tire for condition and balance. Check and tighten the wheel nuts
C0034-76 Right Front Wheel Speed Sensor - Wrong mounting position
  • Front right wheel speed sensor incorrectly installed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check the integrity and positioning of the front right wheel speed sensor mounting and rectify as required
C0036-38 Left Rear Tone Wheel - Signal frequency incorrect
  • Rear left wheel speed sensor not securely mounted
  • Rear left wheel speed sensor magnetic reluctor ring damaged
  • Rear left wheel bearing failure
  • Rear left wheel/tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the rear left wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the rear left wheel speed sensor magnetic reluctor ring. Rectify as required
  • Check the rear left wheel bearing. Rectify as required
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the rear left wheel and tire for condition and balance. Check and tighten the wheel nuts
C0037-11 Left Rear Wheel Speed Sensor - Circuit short to ground
  • Rear left wheel speed sensor signal circuit short circuit to ground
  • Rear left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor as required
C0037-12 Left Rear Wheel Speed Sensor - Circuit short to battery
  • Rear left wheel speed sensor power circuit short circuit to power
  • Rear left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to power. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor
C0037-14 Left Rear Wheel Speed Sensor - Circuit short to ground or open
  • Rear left wheel speed sensor signal circuit short circuit to ground, open circuit, high resistance
  • Rear left wheel speed sensor power circuit open circuit, high resistance
  • Rear left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, open circuit, high resistance. Repair the circuit as required. Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - Left Rear Wheel Speed Sensor Input (2B08)
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor as required
C0037-1C Left Rear Wheel Speed Sensor - Circuit voltage out of range
  • Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor power circuit short circuit to another wheel speed sensor circuit
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to another wheel speed sensor circuit. Repair the circuit as required
C0037-25 Left Rear Wheel Speed Sensor - Signal shape/waveform failure
  • Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor as required
C0037-29 Left Rear Wheel Speed Sensor - Signal invalid
  • Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor as required
C0037-2F Left Rear Wheel Speed Sensor - Signal erratic
  • Rear left wheel speed sensor not securely mounted
  • Rear left wheel speed sensor magnetic reluctor ring damaged
  • Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the rear left wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the rear left wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor as required
C0037-31 Left Rear Wheel Speed Sensor - No signal
  • Rear left wheel speed sensor not securely mounted
  • Rear left wheel speed sensor magnetic reluctor ring damaged
  • Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the rear left wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the rear left wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor as required
C0037-4A Left Rear Wheel Speed Sensor - Incorrect component installed
  • Incorrect rear left wheel speed sensor installed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor of the correct specification as required
C0037-62 Left Rear Wheel Speed Sensor - Signal compare failure
  • Rear left wheel speed sensor not securely mounted
  • Rear left wheel speed sensor magnetic reluctor ring damaged
  • Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the rear left wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the rear left wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear left wheel speed sensor as required
C0037-66 Left Rear Wheel Speed Sensor - Signal has too many transitions/events
  • Rear left wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear left wheel/tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear left wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the rear left wheel and tire for condition and balance. Check and tighten the wheel nuts
C0037-76 Left Rear Wheel Speed Sensor - Wrong mounting position
  • Rear left wheel speed sensor incorrectly installed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check the integrity and positioning of the rear left wheel speed sensor mounting and rectify as required
C0039-38 Right Rear Tone Wheel - Signal frequency incorrect
  • Rear right wheel speed sensor not securely mounted
  • Rear right wheel speed sensor magnetic reluctor ring damaged
  • Rear right wheel bearing failure
  • Rear right wheel/tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the rear right wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the rear right wheel speed sensor magnetic reluctor ring
  • Check the rear right wheel bearing. Rectify as required
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the rear right wheel and tire for condition and balance. Check and tighten the wheel nuts
C003A-11 Right Rear Wheel Speed Sensor - Circuit short to ground
  • Rear right wheel speed sensor signal circuit short circuit to ground
  • Rear right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor as required
C003A-12 Right Rear Wheel Speed Sensor - Circuit short to battery
  • Rear right wheel speed sensor power circuit short circuit to power
  • Rear right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to power. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor as required
C003A-14 Right Rear Wheel Speed Sensor - Circuit short to ground or open
  • Rear right wheel speed sensor signal circuit short circuit to ground, open circuit, high resistance
  • Rear right wheel speed sensor power circuit open circuit, high resistance
  • Rear right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, open circuit, high resistance. Repair the circuit as required. Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - Right Rear Wheel Speed Sensor Input (2B09)
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor as required
C003A-1C Right Rear Wheel Speed Sensor - Circuit voltage out of range
  • Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor power circuit short circuit to another wheel speed sensor circuit
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to another wheel speed sensor circuit. Repair the circuit as required
C003A-25 Right Rear Wheel Speed Sensor - Signal shape/waveform failure
  • Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor as required
C003A-29 Right Rear Wheel Speed Sensor - Signal invalid
  • Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor as required
C003A-2F Right Rear Wheel Speed Sensor - Signal erratic
  • Rear right wheel speed sensor not securely mounted
  • Rear right wheel speed sensor magnetic reluctor ring damaged
  • Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the rear right wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the rear right wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor as required
C003A-31 Right Rear Wheel Speed Sensor - No signal
  • Rear right wheel speed sensor not securely mounted
  • Rear right wheel speed sensor magnetic reluctor ring damaged
  • Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the rear right wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the rear right wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor as required
C003A-4A Right Rear Wheel Speed Sensor - Incorrect component installed
  • Incorrect rear right wheel speed sensor installed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor of the correct specification as required
C003A-62 Right Rear Wheel Speed Sensor - Signal compare failure
  • Rear right wheel speed sensor not securely mounted
  • Rear right wheel speed sensor magnetic reluctor ring damaged
  • Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor signal not plausible when compared to other wheel speed sensors
  • Rear right wheel speed sensor internal failure
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Check the rear right wheel speed sensor is securely mounted, repair as required
  • Check the integrity of the rear right wheel speed sensor magnetic reluctor ring. Rectify as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new rear right wheel speed sensor as required
C003A-66 Right Rear Wheel Speed Sensor - Signal has too many transitions/events
  • Rear right wheel speed sensor power circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel speed sensor signal circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Rear right wheel/tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor power circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the rear right wheel speed sensor signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
  • Check that the wheels and tires comply with the manufacturer's specification for the vehicle. Check the rear right wheel and tire for condition and balance. Check and tighten the wheel nuts
C003A-76 Right Rear Wheel Speed Sensor - Wrong mounting position
  • Rear right wheel speed sensor incorrectly installed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check the integrity and positioning of the rear right wheel speed sensor mounting and rectify as required
C0049-4B Brake Fluid - Over Temperature
NOTE: This DTC is for event information only and does not indicate a fault
  • Brake fluid temperature above maximum threshold
  • Allow the system temperature to return to normal. Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest
  • Allow sufficient time for the brakes to cool. Refer to the relevant service information and check the brake fluid level/condition, repair as required. Clear the Diagnostic Trouble Code(s) and retest
C0049-68 Brake Fluid - Event Information
NOTE: This DTC is for event information only and does not indicate a fault
  • Anti-lock brake system control module is using default initialization values
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest
C0061-64 Lateral Acceleration Sensor - Signal plausibility failure
  • Restraints control module incorrectly installed
  • Lateral acceleration sensor internal failure
NOTE: The sensor is located inside the restraints control module
  • Check the installation of the Restraints control module
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the restraints control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C0062-64 Longitudinal Acceleration Sensor - Signal plausibility failure
  • Restraints control module incorrectly installed
  • Longitudinal acceleration sensor internal failure
NOTE:
  • The sensor is located inside the restraints control module
  • This DTC can be set if the vehicle is being tested on chassis dyno rollers
  • Check the installation of the Restraints control module
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the restraints control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C0063-64 Yaw Rate Sensor - Signal plausibility failure
  • Restraints control module incorrectly installed
  • Yaw rate sensor internal failure
NOTE:
  • The sensor is located inside the restraints control module
  • This DTC can be set if the vehicle is being tested on chassis dyno rollers
  • Check the installation of the Restraints control module
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the restraints control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C0064-64 Roll Rate Sensor - Signal Plausibility Failure
  • Restraints control module incorrectly installed
  • Restraints system fault
NOTE:
  • The sensor is located inside the restraints control module
  • This DTC can be set if the vehicle is being tested on chassis dyno rollers
  • Check the installation of the Restraints control module
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the restraints control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C006B-00 Stability System Active Too Long - No sub type information
  • Wheel speed sensor fault
  • Yaw rate lateral acceleration sensor fault
  • Steering angle sensor fault
NOTE: The yaw rate lateral acceleration sensor is located inside the restraints control module
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check for wheel speed sensor related Diagnostic Trouble Code(s) and perform the relevant corrective actions
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check for yaw rate lateral acceleration sensor related Diagnostic Trouble Code(s) and perform the relevant corrective actions
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check for steering angle sensor related Diagnostic Trouble Code(s) and perform the relevant corrective actions
C0072-4B Brake Temperature Too High - Over temperature
  • Brake disc temperature above maximum threshold
NOTE: This DTC is for event information only and does not indicate a fault
  • Allow the system temperature to return to normal. Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest
C1015-92 Vacuum Supply - Performance Or Incorrect Operation
  • Vacuum system or brake booster air leaks, brake vacuum pump fault
  • Check the brake vacuum system components for air leakages and vacuum pump operation. Repair as required. Clear DTC and retest
C101A-11 Vacuum Pressure Sensor - Circuit Short To Ground
  • Brake vacuum sensor power circuit open circuit, high resistance
  • Brake vacuum sensor signal circuit short circuit to 5 volt power
  • Refer to the electrical circuit diagrams and check the brake vacuum sensor power circuit for open circuit, high resistance. Repair the wiring harness or install a new brake vacuum sensor as necessary
  • Refer to the electrical circuit diagrams and check the brake vacuum sensor signal circuit for short circuit to 5 volt power. Repair the wiring harness or install a new brake vacuum sensor as necessary
C101A-12 Vacuum Pressure Sensor - Circuit Short To Battery
  • Brake vacuum sensor circuit short circuit to power
  • Brake vacuum sensor circuit short circuit to 5 volt power
  • Refer to the electrical circuit diagrams and check the brake vacuum sensor circuit for short circuit to power. Repair the wiring harness as necessary
  • Refer to the electrical circuit diagrams and check the brake vacuum sensor circuit for short circuit to 5 volt power. Repair the wiring harness or install a new brake vacuum sensor as necessary
C101A-1C Vacuum Pressure Sensor - Circuit Voltage Out Of Range
  • Brake vacuum sensor power circuit short circuit to ground, short circuit to power
  • Refer to the electrical circuit diagrams and check the brake vacuum sensor power circuit for short circuit to ground, short circuit to power. Repair the wiring harness or install a new brake vacuum sensor as necessary
C101A-64 Vacuum pressure Sensor - Signal Plausibility Failure
  • Vacuum system or brake booster air leaks, brake vacuum pump fault
  • Brake vacuum sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Check the brake vacuum system components for air leakage and vacuum pump operation. Repair as required. Clear the DTC and retest
  • Refer to the electric circuit diagrams and check the brake vacuum sensor circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required
C101A-81 Vacuum Pressure Sensor - Invalid Serial Data Received
  • Brake vacuum sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Radio frequency interference due to non-genuine accessories
  • Brake vacuum sensor internal failure
  • Refer to the electrical circuit diagrams and check the brake vacuum sensor circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness or install a new brake vacuum sensor as necessary
  • Check for non-genuine accessories. Rectify as necessary
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new brake vacuum sensor as necessary
C101A-86 Vacuum Pressure Sensor - Signal Invalid
  • Brake booster vacuum hose restricted, leaking or installed incorrectly
  • Brake vacuum sensor internal failure
  • Check the integrity of the brake booster vacuum hose. Rectify as necessary
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new brake vacuum sensor as necessary
C101F-49 Generic Valve Failure - Internal electronic failure
  • Anti-lock brake system hydraulic control unit internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new anti-lock brake system control module as required
C1054-68 System Functionality Reduced By Diagnostic Request - Event information
  • System functionality reduced by diagnostic request
NOTE: This DTC is for event information only and does not indicate a fault
  • Perform ignition cycle or press the dynamic stability control on/off switch. Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest
C105C-68 ABS Dynomometer Test Mode Active - Event information
  • Dynamometer test mode active
  • When the brake pedal, accelerator pedal and the DSC switch are continuously pressed simultaneously for over 5 seconds with the steering wheel in the straight ahead position and the vehicle not moving, the dynomometer test mode routine is activated and this DTC is set. The anti-lock brake system and stability control system warning lights are also illuminated
NOTE: This DTC is for event information only and does not indicate a fault
  • Deactivate the dynomometer test mode routine by briefly pressing the DSC switch or moving the steering wheel more than a quarter turn with the ignition switched on. The anti-lock brake system and stability control system warning lights should then extinguish. Clear DTC and retest
C1067-24 All Terrain/Road Progress Control Switch - Signal stuck high
  • All terrain progress control switch stuck active
NOTE: This DTC may be induced by the driver operating the all terrain progress control switch for longer than 60 seconds
  • Check the operation of the all terrain progress control switch. Free the stuck switch, clear the DTC and retest. If the fault persists, using the Jaguar Land Rover Approved Diagnostic Equipment, check the all terrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C1109-24 Vehicle Dynamics Control Switch - Signal stuck high
  • Dynamic stability control switch stuck active
NOTE: This DTC may be induced by the driver operating the dynamic stability control switch for longer than 30 seconds
  • Check the operation of the dynamic stability control switch. Free the stuck switch, clear the DTC and retest. If the fault persists, using the Jaguar Land Rover Approved Diagnostic Equipment, check the all terrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C1137-64 Reverse Gear Switch - Signal plausibility failure
  • Reverse gear switch signal implausible
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C1A43-16 Motor Supply - Circuit voltage below threshold
  • Battery/charging system fault
  • Anti-lock brake system control module power or ground circuit open circuit, high resistance
NOTE: This DTC is set if the electric park brake is operated when the voltage at the anti-lock brake system control module is less than 7.90 volts
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - ECU Power Supply Voltage (D111). Refer to the relevant service information and test the battery and charging system
  • Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair circuit as required. Clear DTC and retest
C1A43-17 Motor Supply - Circuit voltage above threshold
  • Battery/charging system fault
  • Anti-lock brake system control module supply voltage too high during or before electric park brake activation
NOTE: This DTC is set if the electric park brake is operated when the voltage at the anti-lock brake system control module is greater than 17.50 volts
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - ECU Power Supply Voltage (D111). Refer to the relevant service information and test the battery and charging system
  • Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for high resistance. Repair the circuit as required. Clear the DTC and retest
  • Check the alternator output voltage and rectify as required
C1A43-1C Motor Supply - Circuit voltage out of range
  • Battery/charging system fault
  • Anti-lock brake system control module power or ground circuit open circuit, high resistance
NOTE: This DTC is set if the electric park brake is operated when the voltage at the anti-lock brake system control module is less than 8.85 volts
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - ECU Power Supply Voltage (D111). Refer to the relevant service information and test the battery and charging system
  • Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair the circuit as required. Clear the DTC and retest
C1A90-12 Wheel Speed Sensor Supply - Circuit short to battery
  • Wheel speed sensor supply circuits short circuit to power
  • Refer to the electrical circuit diagrams and check the wheel speed sensor supply circuits for short circuit to power. Repair circuits as required. Clear DTC and retest
C1A95-01 Wheel Speed Sensor - General electrical failure
  • Battery/charging system fault
  • Wheel speed sensor signal circuits short circuit to ground, short circuit to power, short circuit to another sensor circuit, open circuit, high resistance
  • Wheel speed sensor(s) internal failure
  • Refer to the relevant service information and test the battery and charging system
  • Refer to the electrical circuit diagrams and check the wheel speed sensor signal circuits for short circuit to ground, short circuit to power, short circuit to another sensor circuit, open circuit, high resistance. Repair circuits as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install new wheel speed sensor(s) as required
C1A95-62 Wheel Speed Sensor - Signal compare failure
  • Wheel speed sensor signal circuits short circuit to ground, short circuit to power, short circuit to another sensor circuit, open circuit, high resistance
  • Wheel speed sensor not securely mounted
  • Wheel speed sensor magnetic reluctor ring damaged
  • Wheel bearing failure
  • Wheel and/or tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the wheel speed sensor signal circuits for short circuit to ground, short circuit to power, short circuit to another sensor circuit, open circuit, high resistance. Repair circuits as required
  • Check the wheel speed sensors are securely mounted, repair as required
  • Check the integrity of the wheel speed sensors magnetic reluctor rings. Rectify as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signals - Left Front Wheel Speed Sensor Input (2B06) - Right Front Wheel Speed Sensor Input (2B07) - Left Rear Wheel Speed Sensor Input (2B08) - Right Rear Wheel Speed Sensor Input (2B09)
  • Check the integrity of the wheel bearings
  • Check that the wheel and tire sizes are correct to the vehicle specification
C1A95-64 Wheel Speed Sensor - Signal plausibility failure
  • Wheel speed sensor signal circuits short circuit to ground, short circuit to power, short circuit to another sensor circuit, open circuit, high resistance
  • Wheel speed sensor magnetic reluctor ring fault
  • Wheel bearing failure
  • Wheel and/or tire size incorrect
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the wheel speed sensor signal circuits for short circuit to ground, short circuit to power, short circuit to another sensor circuit, open circuit, high resistance. Repair circuits as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signals - Left Front Wheel Speed Sensor Input (2B06) - Right Front Wheel Speed Sensor Input (2B07) - Left Rear Wheel Speed Sensor Input (2B08) - Right Rear Wheel Speed Sensor Input (2B09)
  • Check the integrity of the wheel bearings
  • Check that the wheel and tire sizes are correct to the vehicle specification
C1A95-76 Wheel Speed Sensor - Wrong mounting position
  • One or more wheel speed sensors installed incorrectly - Wrong orientation
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check the integrity and positioning of the wheel speed sensor mounting(s) and rectify as required
C1A96-64 Brake Light Switch - Signal plausibility failure
  • Brake pedal switch incorrectly installed
  • Brake pedal switch maladjusted
  • Brake pedal switch circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Irregular use of brake pedal during driving
NOTE: This DTC will log if the brake pedal switch is continuously active for 60 seconds or more while the vehicle speed is 17 km/h (11 mph) or greater and throttle application is at 5% or higher. If all these conditions continue, the Dynamic Stability Control (DSC) warning indicator will illuminate, under some conditions further warning indicators may be activated and a warning message may appear in the message center
  • Check the brake pedal switch installation
  • Check the brake pedal switch adjustment
  • Refer to the electrical circuit diagrams and check the brake pedal switch circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuit as required. Clear the DTC and retest
  • If there are no faults with the brake pedal switch or circuits, clear the DTC and road test the vehicle. To fully test for a brake pedal switch fault during the road test, it is necessary to make sure that the vehicle is driven over 17km/h (11 mph) without the brakes being applied for longer than one minute. If driving conditions demand use of the brake during this 60 second period, the brakes may be applied as required for safe driving, however the brake pedal switch test will need to be restarted
  • If the fault does not occur again during the road test, this may indicate that the DTC is being set as a result of the customer's driving behavior, which may involve either left-foot braking or a foot being rested on the brake pedal during driving. Advise the customer that neither of these practices are recommended and that they should adjust their driving style accordingly
C1A99-14 Pressure Sensor - Circuit short to ground or open
  • Anti-lock brake system hydraulic control unit internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new anti-lock brake system control module as required
C1A99-28 Pressure Sensor - Signal bias level out of range/zero adjustment failure
  • Anti-lock brake system hydraulic control unit internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new anti-lock brake system control module as required
C1B00-64 Steering Angle Sensor - Signal plausibility failure
  • Steering angle sensor incorrectly installed
  • Steering angle sensor internal failure
  • Yaw rate sensor incorrect installation
NOTE: This DTC is set when there is conflicting information coming from the steering angle sensor and the yaw rate sensor
  • Check the operation of the steering angle sensor. If faulty, install a new steering angle sensor module as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check for steering angle sensor related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Check the yaw rate sensor installation and rectify as required
C1B00-92 Steering Angle Sensor - Performance or incorrect operation
  • Steering angle sensor incorrectly installed
  • Steering angle sensor signal output stuck intermittently or permanently
  • Steering angle sensor internal failure
  • Check the steering angle sensor installation and rectify as required
  • Check the operation of the steering angle sensor. If faulty, install a new steering angle sensor module as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check for steering angle sensor related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C1B02-14 Return Pump - Circuit short to ground or open
  • Anti-lock brake system hydraulic control unit pump ground circuit, open circuit, high resistance
NOTE: Make sure there is no movement of the ground stud from the relative body panel. Make sure the ground electrical connectors are clean, flat and securely clamped to the stud
  • Refer to the electrical circuit diagrams and check the anti-lock brake system hydraulic control unit pump ground circuit for open circuit, high resistance. Repair the circuit as required
C1B02-16 Return Pump - Circuit voltage below threshold
  • Anti-lock brake system hydraulic control unit pump circuits short circuit to ground, open circuit, high resistance
  • Anti-lock brake system control module internal failure
NOTE: Check the wiring harness and fuse connection to the anti-lock brake system hydraulic unit pump motor, pin 1 and ground pin 14
  • Refer to the electrical circuit diagrams and check the anti-lock brake system hydraulic control unit pump supply fuse and circuits and the anti-lock brake system control module ground circuits for short circuit to ground, open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new anti-lock brake system control module as required
C1B02-49 Return Pump - Internal electronic failure
  • Anti-lock brake system hydraulic control unit pump ground circuit, open circuit, high resistance
  • Anti-lock brake system control module internal failure
NOTE:
  • After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Make sure there is no movement of the ground stud from the relative body panel. Make sure the ground electrical connectors are clean, flat and securely clamped to the stud
  • Refer to the electrical circuit diagrams and check the anti-lock brake system hydraulic control unit pump ground circuit for open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, install a new anti-lock brake system control module
C1B22-24 Hill Decent Switch - Signal Stuck High
  • Hill descent control switch stuck active
NOTE: This DTC may be induced by the driver operating the hill descent control switch for longer than 60 seconds
  • Check the operation of the hill descent control switch. Free the stuck switch, clear the DTC and retest. If the fault persists, using the Jaguar Land Rover Approved Diagnostic Equipment, check the all terrain control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
C1D00-86 Park Brake Apply Switch - Signal invalid
  • Electric park brake switch signals erratic
  • Electric park brake switch fault
NOTE: This DTC may relate to a fault in the wider electric park brake system or the switch. As such, it is recommended that all Diagnostic Trouble Code(s) relating to the electric park brake system are checked and rectified as the first action
  • Check for any electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Refer to the electrical circuit diagrams and check the electric park brake switch circuits for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuits as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new electric park brake switch as required
C2005-07 Right Actuator - Mechanical failures
  • Electric park brake right actuator motor free-run current too high during clamping or releasing
  • Electric park brake right actuator internal failure
  • Check that the electric park brake right actuator is correctly installed
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2005-1B Right Actuator - Circuit resistance above threshold
  • Electric park brake right actuator circuits open circuit, high resistance
  • Refer to the electrical circuit diagrams and check the right electric park brake actuator circuits for open circuit, high resistance. Repair circuits as required
  • Check for any electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest
C2005-71 Right Actuator - Actuator stuck
  • Electric park brake right actuator incorrectly installed
  • Electric park brake right actuator internal failure
  • Check that the electric park brake right actuator is correctly installed
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2005-77 Right Actuator - Commanded position not reachable
  • Right actuator low supply voltage
  • Right electric park brake actuator, brake disc or brake pads not installed correctly
  • Right electric park brake actuator circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Anti-lock brake system control module power or ground circuit open circuit, high resistance
  • Right electric park brake actuator mechanical failure
  • Check the right actuator battery supply voltage
  • Check that the right electric park brake actuator, brake disc or brake pads are installed correctly. Repair as required
  • Refer to the electrical circuit diagrams and check the right electric park brake actuator circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuits as required
  • Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair the circuits as required
  • Perform an ignition cycle and retest the electric park brake, if the fault persists, install a new right electric park brake actuator as necessary
C2006-07 Left Actuator - Mechanical failures
  • Electric park brake left actuator motor running without any corresponding apply or release
  • Electric park brake left actuator motor free-run current too high during clamping or releasing
  • Electric park brake left actuator internal failure
  • Check that the electric park brake left actuator is correctly installed
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, check and install a new electric park brake left actuator as required
C2006-1B Left Actuator - Circuit resistance above threshold
  • Electric park brake left actuator circuits open circuit, high resistance
  • Refer to the electrical circuit diagrams and check the left electric park brake actuator circuits for open circuit, high resistance. Repair circuits as required
  • Check for any electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest
C2006-71 Left Actuator - Actuator stuck
  • Electric park brake left actuator incorrectly installed
  • Electric park brake left actuator internal failure
  • Check that the electric park brake left actuator is correctly installed
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake left actuator as required
C2006-77 Left Actuator - Commanded position not reachable
  • Left actuator low supply voltage
  • Left electric park brake actuator, brake disc or brake pads not installed correctly
  • Left electric park brake actuator circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Anti-lock brake system control module power or ground circuit open circuit, high resistance
  • Left electric park brake actuator mechanical failure
  • Check the left actuator battery supply voltage
  • Check that the left electric park brake actuator, brake disc or brake pads are installed correctly. Repair as required
  • Refer to the electrical circuit diagrams and check the left electric park brake actuator circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuits as required
  • Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair the circuits as required
  • Perform an ignition cycle and retest the electric park brake, if the fault persists, install a new left electric park brake actuator as necessary
C2007-01 Right Motor - General electrical failure
  • Anti-lock brake system control module internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists install a new anti-lock brake system control module as necessary
C2007-11 Right Motor - Circuit short to ground
  • Electric park brake right actuator circuits short circuit to ground
  • Refer to the electrical circuit diagrams and check the electric park brake right actuator circuits for short circuit to ground. Repair circuits as required. Clear DTC and retest
C2007-12 Right Motor - Circuit short to battery
  • Electric park brake right actuator circuits short circuit to power
  • Refer to the electrical circuit diagrams and check the electric park brake right actuator circuits for short circuit to power. Repair circuits as required. Clear DTC and retest
C2007-13 Right Motor - Circuit open
  • Electric park brake control module right actuator circuits open circuit, high resistance
  • Electric park brake right actuator internal failure
  • Refer to the electrical circuit diagrams and check the electric park brake control module right actuator circuits for open circuit, high resistance. Repair the circuits as required. Clear the DTC and retest
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2007-16 Right Motor - Circuit Voltage Below Threshold
NOTE: This DTC is set if the electric park brake is operated when the voltage at the anti-lock brake system control module is less than 7.90 Volts
  • Anti-lock brake system control module power or ground circuit open circuit, high resistance
  • Battery/charging system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Power Supply Voltage (D111). Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair the circuit as required
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Supply Voltage (0xD111). Refer to the relevant service information and test the battery and charging system
C2007-18 Right Motor - Circuit current below threshold
  • Electric park brake control module right actuator circuits open circuit, high resistance
  • The polarity of the right electronic park brake actuator is incorrect
  • Anti-lock brake system control module power or ground circuits open circuit, high resistance
  • Electric park brake right actuator internal failure
  • Battery/charging system fault
  • Check the integrity of the brake disc and brake pads and that the electric park brake right actuator is correctly installed
  • Refer to the electrical circuit diagrams and check the electric park brake right actuator circuits for correct polarity and for open circuit, high resistance. Repair circuits as required
  • Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair circuits as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake right actuator as required
  • Refer to the relevant service information and test the battery and charging system
C2007-19 Right Motor - Circuit current above threshold
  • Electric park brake right actuator circuit(s) short circuit to ground, short circuit to power
  • Other electric park brake actuator Diagnostic Trouble Code(s)
  • Rear right brake caliper seized or brake pads binding in the caliper
  • Park brake actuator blocked
  • Electric park brake right actuator internal failure
  • Refer to the electrical circuit diagrams and check the electric park brake right actuator circuits for short circuit to ground, short circuit to power. Repair circuit(s) as required. Clear Diagnostic Trouble Code(s), apply the park brake and retest
  • Check for any other electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Check for a seized rear right brake caliper, or brake pads binding in the caliper. Rectify as necessary
  • If the fault persists, run calibration routine - Assembly Test - to return the actuator to the normal position
  • If the fault persists, cycle ignition and clear Diagnostic Trouble Code(s). Temporarily connect the left actuator harness to the right actuator and vice versa, then apply and release the park brake. If DTC C2008-19 is set, replace the electric park brake right actuator. If DTC C2007-19 is set, check the electric park brake right actuator power circuit for short circuit faults and repair circuits as required. Reconnect actuator harnesses in original positions, clear Diagnostic Trouble Code(s) and retest
C2007-1D Right Motor - Circuit current out of range
  • Electric park brake right actuator power or ground circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Electric park brake right actuator internal failure
  • Refer to the electrical circuit diagrams and check the electric park brake right actuator power or ground circuit for short circuit to ground, short circuit to power, open circuit, high resistance
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2007-1E Right Motor - Circuit resistance out of range
  • Electric park brake right actuator circuits short circuit together, short circuit to ground, short circuit to power, open circuit, high resistance
  • Electric park brake right actuator internal failure
  • Refer to the electrical circuit diagrams and check the electric park brake right actuator circuits for short circuit together, short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuits as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2007-71 Right Motor - Actuator stuck
  • Electric park brake right actuator incorrectly installed
  • Electric park brake right actuator circuits open circuit, high resistance
  • Electric park brake right actuator internal failure
  • Check that the electric park brake right actuator is correctly installed
  • Refer to the electrical circuit diagrams and check the electric park brake right actuator circuits for open circuit, high resistance. Repair circuits as required
  • Check for any electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2007-72 Right Motor - Actuator stuck open
  • Electric park brake right actuator incorrectly installed
  • Electric park brake right actuator internal failure
  • Check that the electric park brake right actuator is correctly installed
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2007-73 Right Motor - Actuator stuck closed
  • Electric park brake right actuator incorrectly installed
  • Electric park brake right actuator internal failure
  • Check that the electric park brake right actuator is correctly installed
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2007-77 Right Motor - Commanded position not reachable
  • The anti-lock brake system control module has powered down unexpectedly (caused by battery removal/replacement or a diagnostic reset performed on the anti-lock brake system control module). The electric park brake control system cannot determine the position of the right brake caliper
  • Electric park brake right actuator circuits short circuit to ground, short circuit to power, open circuit, high resistance
  • Battery/charging system fault
  • Electric park brake right actuator internal failure
  • Apply and release the electric park brake switch to clear the fault. Clear the DTC and retest
  • Refer to the electrical circuit diagrams and check the electric park brake right actuator circuits for correct polarity and for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuits as required
  • Refer to the relevant service information and test the battery and charging system
  • Check for any electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake right actuator as required
C2008-01 Left Motor - General electrical failure
  • Anti-lock brake system control module internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists install a new anti-lock brake system control module as necessary
C2008-11 Left Motor - Circuit short to ground
  • Electric park brake left actuator circuits short circuit to ground
  • Refer to the electrical circuit diagrams and check the electric park brake left actuator circuits for short circuit to ground. Repair circuits as required. Clear DTC and retest
C2008-12 Left Motor - Circuit short to battery
  • Electric park brake left actuator circuits short circuit to power
  • Refer to the electrical circuit diagrams and check the electric park brake left actuator circuits for short circuit to power. Repair circuits as required. Clear DTC and retest
C2008-13 Left Motor - Circuit open
  • Electric park brake control module left actuator circuits open circuit, high resistance
  • Electric park brake left actuator internal failure
  • Refer to the electrical circuit diagrams and check the electric park brake control module left actuator circuits for open circuit, high resistance. Repair the circuits as required. Clear the DTC and retest
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake left actuator as required
C2008-16 Left Motor - Circuit voltage below threshold
NOTE: This DTC is set if the electric park brake is operated when the voltage at the anti-lock brake system control module is less than 7.90 Volts
  • Anti-lock brake system control module power or ground circuits open circuit, high resistance
  • Battery/charging system fault
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Power Supply Voltage (0xD111). Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair the circuits as required
  • Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Supply Voltage (0xD111). Refer to the relevant service information and test the battery and charging system
C2008-18 Left Motor - Circuit current below threshold
  • Electric park brake control module left actuator circuits open circuit, high resistance
  • The polarity of the left electronic park brake actuator is incorrect
  • Anti-lock brake system control module power or ground circuits open circuit, high resistance
  • Electric park brake left actuator internal failure
  • Battery/charging system fault
  • Check the integrity of the brake disc and brake pads and that the electric park brake left actuator is correctly installed
  • Refer to the electrical circuit diagrams and check the electric park brake left actuator circuits for correct polarity and for open circuit, high resistance. Repair circuits as required
  • Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair circuits as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake left actuator as required
  • Refer to the relevant service information and test the battery and charging system
C2008-19 Left Motor - Circuit current above threshold
  • Electric park brake left actuator circuit(s) short circuit to ground, short circuit to power
  • Other electric park brake actuator Diagnostic Trouble Code(s)
  • Rear left brake caliper seized or brake pads binding in the caliper
  • Park brake actuator blocked
  • Electric park brake left actuator internal failure
  • Refer to the electrical circuit diagrams and check the electric park brake left actuator circuits for short circuit to ground, short circuit to power. Repair circuit(s) as required. Clear Diagnostic Trouble Code(s), apply the park brake and retest
  • Check for any other electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Check for a seized rear left brake caliper, or brake pads binding in the caliper. Rectify as necessary
  • If the fault persists, run calibration routine - Assembly Test - to return the actuator to the normal position
  • If the fault persists, cycle ignition and clear Diagnostic Trouble Code(s). Temporarily connect the right actuator harness to the left actuator and vice versa, then apply and release the park brake. If DTC C2007-19 is set, replace the electric park brake left actuator. If DTC C2008-19 is set, check the electric park brake left actuator power circuit for short circuit faults and repair circuits as required. Reconnect actuator harnesses in original positions, clear Diagnostic Trouble Code(s) and retest
C2008-1D Left Motor - Circuit current out of range
  • Electric park brake left actuator power or ground circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Electric park brake left actuator internal failure
  • Refer to the electrical circuit diagrams and check the electric park brake left actuator power or ground circuit for short circuit to ground, short circuit to power, open circuit, high resistance
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake left actuator as required
C2008-1E Left Motor - Circuit resistance out of range
  • Electric park brake left actuator circuits short circuit together, short circuit to ground, short circuit to power, open circuit, high resistance
  • Electric park brake left actuator internal failure
  • Refer to the electric circuit diagrams and check the electric park brake left actuator circuits for short circuit together, short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuits as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new electric park brake left actuator as required
C2008-71 Left Motor - Actuator stuck
  • Electric park brake left actuator incorrectly installed
  • Electric park brake left actuator circuits open circuit, high resistance
  • Electric park brake left actuator internal failure
  • Check that the electric park brake left actuator is correctly installed
  • Refer to the electrical circuit diagrams and check the electric park brake left actuator circuits for open circuit, high resistance. Repair circuits as required
  • Check for any electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake left actuator as required
C2008-72 Left Motor - Actuator stuck open
  • Electric park brake left actuator incorrectly installed
  • Electric park brake left actuator internal failure
  • Check that the electric park brake left actuator is correctly installed
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, check and install a new electric park brake left actuator as required
C2008-73 Left Motor - Actuator stuck closed
  • Electric park brake left actuator incorrectly installed
  • Electric park brake left actuator internal failure
  • Check that the electric park brake left actuator is correctly installed
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, check and install a new electric park brake left actuator as required
C2008-77 Left Motor - Commanded position not reachable
  • The anti-lock brake system control module has powered down unexpectedly (caused by battery removal/replacement or a diagnostic reset performed on the anti-lock brake system control module). The electric park brake control system cannot determine the position of the left brake caliper
  • Electric park brake left actuator circuits short circuit to ground, short circuit to power, open circuit, high resistance
  • Battery/charging system fault
  • Electric park brake left actuator internal failure
  • Apply and release the electric park brake switch to clear the fault. Clear the DTC and retest
  • Refer to the electrical circuit diagrams and check the electric park brake left actuator circuits for correct polarity and for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuits as required
  • Refer to the relevant service information and test the battery and charging system
  • Check for any electric park brake actuator-related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s), then apply and release the park brake and retest. If the fault persists, check and install a new electric park brake left actuator as required
C2009-95 Front Axle Wheel Speed Sensors Swapped - Incorrect assembly
  • Front wheel speed sensor connectors transposed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the front wheel speed sensor circuits for correct connection to the anti-lock brake system control module. Rectify as necessary
C200A-95 Rear Axle Wheel Speed Sensors Swapped - Incorrect assembly
  • Rear wheel speed sensor connectors transposed
NOTE: After clearing the Diagnostic Trouble Code(s), the warning indicator(s) may not extinguish until the vehicle speed has exceeded 15 km/h (10 mph)
  • Refer to the electrical circuit diagrams and check the rear wheel speed sensor circuits for correct connection to the anti-lock brake system control module. Rectify as necessary
P0607-49 Control Module Performance - Internal Electronic Failure
  • Anti-lock brake system control module internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new anti-lock brake system control module
U0046-81 Vehicle Communication Bus C - Invalid Serial Data Received
  • Invalid data received from another control module through the high speed CAN bus (chassis)
NOTE: This is not a vehicle harness issue or anti-lock brake system control module issue. The data source module has sent information which it has marked as Invalid
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0046-82 Vehicle Communication Bus C - Alive/Sequence Counter Incorrect/Not Updated
  • Invalid data received from another control module through the high speed CAN bus (chassis)
NOTE: This is not a vehicle harness issue or anti-lock brake system control module issue. The data source module has not performed a calculation correctly
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0046-83 Vehicle Communication Bus C - Value of Signal Calculation Incorrect
  • Invalid data received from another control module through the high speed CAN bus (chassis)
NOTE: This is not a vehicle harness issue or anti-lock brake system control module issue. The data source module has not performed a calculation correctly
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0046-86 Vehicle Communication Bus C - Signal Invalid
  • Restraints control module incorrectly installed
  • Invalid data received from the restraints control module through the high speed CAN bus (chassis)
  • Steering angle sensor incorrectly installed
  • Invalid data received from the steering angle sensor through the high speed CAN bus (chassis)
NOTE: This DTC relates to data received from the restraints control module or the steering wheel angle sensor module
  • Check the installation of the Restraints control module
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the restraints control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
  • Check the operation of the steering angle sensor. If faulty, install a new steering angle sensor module as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check for steering angle sensor related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0046-87 Vehicle Communication Bus C - Missing Message
  • Invalid data received from another control module through the high speed CAN bus (chassis)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0046-88 Vehicle Communication Bus C - Bus Off
  • High speed CAN bus (chassis) circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, perform a CAN network integrity test. Refer to the electrical circuit diagrams and check the high speed CAN bus (chassis) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
U0080-81 Vehicle Communication Bus F - Invalid Serial Data Received
  • Invalid data received from another control module through the FlexRay bus
NOTE: This is not a vehicle harness issue or anti-lock brake system control module issue. The data source module has sent information which it has marked as Invalid
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0080-82 Vehicle Communication Bus F - Alive/Sequence Counter Incorrect/Not Updated
  • Invalid data received from another control module through the FlexRay bus
NOTE: This is not a vehicle harness issue or anti-lock brake system control module issue. The data source module has not performed a calculation correctly
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0080-83 Vehicle Communication Bus F - Value Of Signal Protection Calculation Incorrect
  • Invalid data received from another control module through the FlexRay bus
NOTE: This is not a vehicle harness issue or anti-lock brake system control module issue. The data source module has not performed a calculation correctly
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0080-87 Vehicle Communication Bus F - Missing Message
  • Missing message from another control module through the FlexRay bus
NOTE: The FlexRay wiring harness must not be repaired by making a localised wiring repair. A new wiring harness should be installed
  • Using Jaguar Land Rover Approved Diagnostic Equipment, check the snapshot data to determine the missing message source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0080-88 Vehicle Communication Bus F - Buss Off
  • FlexRay bus (body) circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Refer to the electrical circuit diagrams and check the FlexRay bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
U0405-68 Invalid Data Received From Cruise Control Module - Event information
  • Missing/invalid data from the adaptive cruise control module
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check the adaptive cruise control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U1A4C-00 Build/End of Line mode Active - No sub type information
  • Electric park brake maintenance mode is active
NOTE: This DTC is for event information only and does not indicate a fault
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, perform routine - Exit Maintenance Mode (302D) - to exit maintenance mode. Clear DTC and retest
U1A4C-68 Build/End of Line mode Active - Event information
  • Electric park brake end of line mode is active
NOTE: This DTC is for use during production only. This DTC is for event information only and does not indicate a fault
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, perform routine - Clear EPB Build/End Of Line Mode (3042) - to exit end of line mode. Clear DTC and retest
U2000-98 Motor Temperature - Component or system over temperature
  • The calculated brake temperature has exceeded a high temperature threshold
  • Allow brakes to cool. Clear the DTC and retest
U2002-13 Switch - Circuit open
  • Electric park brake switch circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Electric park brake switch internal failure
NOTE: To validate the repair, cycle the ignition or with the ignition set to on apply and release the electric park brake
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and check data logging signal - Electric Park Brake - Switch Input Status 2B14. Operate the electric park brake switch and check the switch positions are being recognized correctly by the module. Re-check Diagnostic Trouble Code(s) and repair as necessary
  • Refer to the electrical circuit diagrams and check the electric park brake switch circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new electric park brake switch as required
U2002-2A Switch - Signal stuck in range
  • Electric park brake switch stuck active
  • Electric park brake switch internal failure
NOTE: This DTC may be induced by the driver operating the electric park brake switch for longer than 2.5 minutes
  • Check the operation of the electric park brake switch. Check for foreign objects jamming or obstructing the switch. Rectify as necessary
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new electric park brake switch as required
U2002-92 Switch - Performance or incorrect operation
  • Electric park brake switch circuit short circuit to ground, short circuit to power, open circuit, high resistance
  • Electric park brake switch stuck active
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and check data logging signal - Electric Park Brake - Switch Input Status 2B14. Operate the electric park brake switch and check the switch positions are being recognized correctly by the module. Re-check Diagnostic Trouble Code(s) and repair as necessary
  • Refer to the electrical circuit diagrams and check the electric park brake switch circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the circuits as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new electric park brake switch as required
U2012-00 Car Configuration Parameter(s) - No sub type information
  • Car configuration file mismatch with vehicle specification
  • Anti-lock brake system control module is not correctly configured
NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the Diagnostic Trouble Code(s)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check and up-date the car configuration file as necessary. Clear the Diagnostic Trouble Code(s) and retest
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, reconfigure the anti-lock brake system control module with the latest level software calibration. Clear the DTC and retest
U201A-55 Control Module Main Calibration Data - Not configured
  • Anti-lock brake system control module is not correctly configured
NOTE: The Software consists of an application and calibration file. This DTC indicates a missing calibration file
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, re-configure the anti-lock brake system control module with the latest level software calibration. Clear the DTC and retest
U201A-57 Control Module Main Calibration Data - Invalid Incomplete Software Component
  • Anti-lock brake system control module is not configured correctly
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, re-configure the anti-lock brake system control module with the latest level software. Clear the DTC and retest
U2100-54 Initial Configuration Not Complete - Missing calibration
  • Anti-lock brake system control module assembly check not completed
NOTE: The park brake yellow warning indicator will also be illuminated
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, perform routine - Assembly Test (0211) - before clearing this DTC
U2300-54 Central Configuration - Missing calibration
  • Car configuration file mismatch with vehicle specification
  • Anti-lock brake system control module is not correctly configured
NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the Diagnostic Trouble Code(s)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check and up-date the car configuration file as necessary. Clear the DTC and retest
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, reconfigure the anti-lock brake system control module with the latest level software calibration. Clear the DTC and retest
U3000-04 Control Module - System internal failures
  • Anti-lock brake system control module internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check for relevant electric park brake Diagnostic Trouble Code(s). Repair as necessary, clear the Diagnostic Trouble Code(s) and retest
  • If the fault persists, release and apply the electric park brake, check for relevant Diagnostic Trouble Code(s) and repair as necessary. If the fault still persists install a new anti-lock brake system control module
U3000-44 Control Module - Data Memory Failure
  • Anti-lock brake system control module failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, re-configure the anti-lock brake system control module with the latest level software. Clear the Diagnostic Trouble Code(s) and retest. If the fault persists, check and install a new anti-lock brake system control module as required
U3000-46 Control Module - Calibration/parameter memory failure
  • Anti-lock brake system control module is not correctly configured
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, re-configure the anti-lock brake system control module with the latest level software. Clear the DTC and retest. If the fault persists, check and install a new anti-lock brake system control module as required
U3000-48 Control Module - Supervision software failure
  • Anti-lock brake system control module is not correctly configured
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, re-configure the anti-lock brake system control module with the latest level software. Clear the DTC and retest. If the fault persists, check and install a new anti-lock brake system control module as required
U3000-49 Control Module - Internal electronic failure
  • Anti-lock brake system hydraulic control unit pump ground circuit, open circuit, high resistance
  • Anti-lock brake system control module internal failure
NOTE: Make sure there is no movement of the ground stud from the relative body panel. Make sure the ground electrical connectors are clean, flat and securely clamped to the stud
  • Refer to the electrical circuit diagrams and check the anti-lock brake system hydraulic control unit pump ground circuit for open circuit, high resistance. Repair the circuit as required
  • Refer to the electrical circuit diagrams and check the polarity of the left and right motor. Repair the circuit(s) as required
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, install a new anti-lock brake system control module as required
U3000-4B Control Module - Over temperature
  • Anti-lock brake system hydraulic control unit internal temperature above maximum threshold
NOTE:
  • This DTC may be set if the Jaguar Land Rover Approved Diagnostic Equipment has been operating the valves for a prolonged period
  • If this DTC is set do not replace the anti-lock brake system control module
  • Allow sufficient time for the unit to cool. Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest
U3000-51 Control Module - Not programed
  • Anti-lock brake system control module is not correctly configured
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, re-configure the anti-lock brake system control module with the latest level software. Clear the DTC and retest. If the fault persists, check and install a new anti-lock brake system control module as required
U3000-55 Control Module - Not configured
  • Car configuration file mismatch with vehicle specification
  • Anti-lock brake system control module is not correctly configured
NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the Diagnostic Trouble Code(s)
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check and up-date the car configuration file as necessary. Clear the Diagnostic Trouble Code(s) and retest
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, reconfigure the anti-lock brake system control module with the latest level software calibration. Clear the DTC and retest
U3000-57 Control Module - Invalid/incomplete software component
  • Anti-lock brake system control module is not configured correctly
  • Anti-lock brake system control module internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, re-configure the anti-lock brake system control module with the latest level software
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, install a new anti-lock brake system control module
U3000-92 Control Module - Performance or incorrect operation
  • Anti-lock brake system control module internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the Diagnostic Trouble Code(s) and retest by applying and releasing the electric park brake. If the fault persists, install a new anti-lock brake system control module
U3001-44 Control Module Improper Shutdown - Data memory failure
  • Anti-lock brake system control module internal failure
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, clear the DTC and retest. If the fault persists, check and install a new anti-lock brake system control module as required
U3001-77 Control Module Improper Shutdown - Commanded position not reachable
  • Anti-lock brake system control module electric park brake control system has powered down unexpectedly (caused by battery removal/replacement or a diagnostic reset performed on the anti-lock brake system control module). The anti-lock brake system control module electric park brake control system cannot determine the position of the rear brake calipers
  • Apply and release the electric park brake switch to clear the fault. Clear the DTC and retest
U3006-16 Control Module Input Power "A" - Circuit voltage below threshold
  • Battery/charging system fault
  • Anti-lock brake system control module power or ground circuit open circuit high resistance
  • Using the Jaguar Land Rover Approved Diagnostic Equipment, check datalogger signal - ECU Power Supply Voltage (D111). Refer to the relevant service information and test the battery and charging system
  • Refer to the electrical circuit diagrams and check the anti-lock brake system control module power and ground circuits for open circuit, high resistance. Repair the circuit as required
scientia non olet · About LEMON Manuals