Infotainment Master Controller (IMC)/Infotainment Slave Controller (ISC)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.

NOTE:

Guided Diagnostics must be followed and the repair advised by the process completed. Failure to do so may result in the rejection of any warranty claim made.
If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual, or determine if any prior approval program is in operation, prior to the installation of a new module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the Jaguar Land Rover Approved Diagnostic Equipment).
When performing voltage or resistance tests, always use a digital multimeter that has the resolution ability to view 3 decimal places. For example, on the 2 volts range can measure 1 mV or 2 K Ohm range can measure 1 Ohm. When testing resistance always take the resistance of the digital multimeter leads into account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
Check JLR claims submission system for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific customer complaint and carry out the recommendations as required.

The DTC Index lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Infotainment Master Controller (IMC)/Infotainment Slave Controller (ISC). For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing service information.

DTC	DESCRIPTION	POSSIBLE CAUSES	ACTION
B1087-83	LIN Bus "A" - Value of signal protection calculation incorrect	Infotainment master controller is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B1087-86	LIN Bus "A" - Signal invalid	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
B1087-87	LIN Bus "A" - Missing message	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
B1087-88	LIN Bus "A" - Bus off	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
B119F-11	GPS Antenna - Circuit short to ground	Global positioning system antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the global positioning system antenna circuit for short circuit to ground
B119F-15	GPS Antenna - Circuit short to battery or open	Global positioning system antenna circuit short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the global positioning system antenna circuit for short circuit to power, open circuit, high resistance
B11A4-11	L-Band Antenna - Circuit short to ground	Digital radio L-band antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the digital radio L-band antenna circuit for short circuit to ground
B11A4-12	L-Band Antenna - Circuit short to battery	Digital radio L-band antenna circuit short circuit to power	Refer to the electrical circuit diagrams and check the digital radio L-band antenna circuit for short circuit to power
B11A4-13	L-Band Antenna - Circuit open	Digital radio L-band antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the digital radio L-band antenna circuit for open circuit, high resistance
B11A5-11	Band 3 Antenna - Circuit short to ground	Digital radio band 3 antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the digital radio band 3 antenna circuit for short circuit to ground
B11A5-12	Band 3 Antenna - Circuit short to battery	Digital radio band 3 antenna circuit short circuit to power	Refer to the electrical circuit diagrams and check the digital radio band 3 antenna circuit for short circuit to power
B11A5-13	Band 3 Antenna - Circuit open	Digital radio band 3 antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the digital radio band 3 antenna circuit for open circuit, high resistance
B121C-93	Hard Drive - No operation	Infotainment master controller hard drive internal failure	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B137F-31	Steering Wheel Left Switch Pack - No signal	Steering wheel left switchpack power or ground circuit open circuit, high resistance LIN bus circuit short circuit to ground, short circuit to power, open circuit, high resistance Steering wheel left switchpack internal failure	Refer to the electrical circuit diagrams and check the steering wheel left switchpack power and ground circuits for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the LIN bus circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new steering wheel left switchpack
B1492-11	Microphone #1 Input Signal - Circuit short to ground	NOTE: There are two different types of microphone fitted to the vehicle. One type of microphone has one inner circuit and an outer screen while the other type has two inner circuits and an outer screen. Ensure all circuits are tested where appropriate Infotainment master controller microphone 1 circuit short circuit to ground Infotainment slave controller (where fitted) microphone 1 circuit short circuit to ground	NOTE: If this DTC is logged simultaneously with a cluster of DTCs including U200F-11, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the infotainment master controller microphone 1 circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) microphone 1 circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest
B1492-12	Microphone #1 Input Signal - Circuit short to battery	Infotainment master controller microphone 1 circuit short circuit to power Infotainment slave controller (where fitted) microphone 1 circuit short circuit to power	NOTE: If this DTC is logged simultaneously with a cluster of DTCs including U200F-11, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the infotainment master controller microphone 1 circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) microphone 1 circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest
B1492-13	Microphone #1 Input Signal - Circuit open	Infotainment master controller microphone 1 circuit open circuit, high resistance Infotainment slave controller (where fitted) microphone 1 circuit open circuit, high resistance	NOTE: If this DTC is logged simultaneously with a cluster of DTCs including U200F-11, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the infotainment master controller microphone 1 circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) microphone 1 circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B1492-15	Microphone #1 Input Signal - Circuit short to battery or open circuit	NOTE: The microphone has two inner circuits and an outer screen. Ensure both inner circuits are tested Infotainment master controller microphone 1 circuit open circuit, high resistance or short circuit to power Infotainment slave controller (where fitted) microphone 1 circuit open circuit, high resistance or short circuit to power	NOTE: If this DTC is logged simultaneously with a cluster of DTCs including U200F-11, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the infotainment master controller microphone 1 circuit for open circuit, high resistance or short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) microphone 1 circuit for open circuit, high resistance or short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest
B1492-1A	Microphone #1 Input Signal - Circuit Resistance Below Threshold	NOTE: The microphone has two inner circuits and an outer screen. Ensure both inner circuits are tested Infotainment master controller microphone 1 circuit low resistance or short circuit between the two inner microphone circuits Infotainment slave controller (where fitted) microphone 1 circuit low resistance or short circuit between the two inner microphone circuits	NOTE: If this DTC is logged simultaneously with a cluster of DTCs including U200F-11, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the infotainment master controller microphone 1 circuit(s) for a low resistance or short circuit between the two inner microphone circuits. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment master controller microphone 1 circuit(s) for a low resistance or short circuit between the two inner microphone circuits. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14A1-11	Microphone #2 Input Signal - Circuit short to ground	Infotainment master controller microphone 2 circuit short circuit to ground Infotainment slave controller (where fitted) microphone 2 circuit short circuit to ground	Refer to the electrical circuit diagrams and check the infotainment master controller microphone 2 circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) microphone 2 circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14A1-12	Microphone #2 Input Signal - Circuit short to battery	Infotainment master controller microphone 2 circuit short circuit to power Infotainment slave controller (where fitted) microphone 2 circuit short circuit to power	Refer to the electrical circuit diagrams and check the infotainment master controller microphone 2 circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) microphone 2 circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14A1-13	Microphone #2 Input Signal - Circuit open	Infotainment master controller microphone 2 circuit open circuit, high resistance Infotainment slave controller (where fitted) microphone 2 circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment master controller microphone 2 circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) microphone 2 circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14A3-02	APIX Display Link - User Interface Panel - General signal failure	Infotainment master controller portable audio interface panel APIX circuit open circuit, high resistance Infotainment slave controller (where fitted) rear portable audio interface panel APIX circuit 1 open circuit, high resistance	NOTE: This DTC will be also be logged if the USB cable is disconnected from the infotainment master controller, or disconnected between the USB repeater module (where fitted) and the portable audio interface panel. If this DTC is logged, also check for DTC B14B6-13 Refer to the electrical circuit diagrams and check the infotainment master controller portable audio interface panel APIX circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) rear portable audio interface panel APIX circuit 1 for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14A3-31	APIX Display Link - User Interface Panel - No signal	Infotainment master controller portable audio interface panel APIX link active with no video Infotainment slave controller (where fitted) rear portable audio interface panel APIX link active with no video	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller to the latest level software. Clear the DTCs and retest If the fault persists, replace the portable audio interface panel and retest If the fault persists, replace the infotainment master controller Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment slave controller (where fitted) to the latest level software. Clear the DTCs and retest If the fault persists, replace the rear portable audio interface panel and retest If the fault persists, replace the infotainment slave controller (where fitted)
B14A4-02	APIX Display Link - Instrument Pack - General signal failure	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
B14A5-08	BroadR-Reach Link - Amplifier (+) - Bus signal/message failures	Audio amplifier module BroadR-Reach® circuit short circuit between positive and negative	Refer to the electrical circuit diagrams and check the audio amplifier module BroadR-Reach® circuit for short circuit across BroadR-Reach® positive and negative pins
B14A5-13	BroadR-Reach Link - Amplifier (+) - Circuit open	Audio amplifier module BroadR-Reach® circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the audio amplifier module BroadR-Reach® circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14A7-13	BroadR-Reach Link - Infotainment Slave - Link #1 (+) - Circuit open	Infotainment slave controller BroadR-Reach® Link#1 circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment slave controller BroadR-Reach® Link#1 circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14A8-08	BroadR-Reach Link - Infotainment Slave - Link #1 (-) - Bus signal/message failures	Infotainment slave controller BroadR-Reach® Link#1 circuit short circuit between positive and negative	Refer to the electrical circuit diagrams and check the infotainment slave controller BroadR-Reach® Link#1 for short circuit across BroadR-Reach® positive and negative pins
B14A9-08	BroadR-Reach Link - Telematics (+) - Bus signal/message failures	Telematics control module BroadR-Reach® circuit short circuit between positive and negative	Refer to the electrical circuit diagrams and check the telematics control module BroadR-Reach® for short circuit across BroadR-Reach® positive and negative pins
B14A9-13	BroadR-Reach Link - Telematics (+) - Circuit open	Telematics control module BroadR-Reach® circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the telematics control module BroadR-Reach® circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AB-11	Infotainment Slave Wake-up/Enable Control - Circuit short to ground	NOTE: Circuit reference - ISC WAKE UP - Infotainment slave controller wake up circuit short circuit to ground	Refer to the electrical circuit diagrams and check the infotainment slave controller wake up circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AB-15	Infotainment Slave Wake-up/Enable Control - Circuit short to battery or open	NOTE: This DTC will log in Service 19 Only after On Demand Self Test is run Circuit reference - ISC WAKE UP - Infotainment slave controller wake up circuit short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment slave controller wake up circuit for short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AB-19	Infotainment Slave Wake-up/Enable Control - Circuit current above threshold	NOTE: Circuit reference - ISC WAKE UP - Infotainment slave controller wake up circuit short circuit to ground Infotainment slave controller not correctly configured Infotainment slave controller internal failure Infotainment master controller not correctly configured Infotainment master controller internal failure	Refer to the electrical circuit diagrams and check the infotainment slave controller wake up circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest If the rear seat entertainment system does not function normally, using the Jaguar Land Rover approved diagnostic equipment, ensure the infotainment slave controller is configured with the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment slave controller. Contact the Jaguar Land Rover service desk for further assistance If the rear seat entertainment system functions normally, using the Jaguar Land Rover approved diagnostic equipment, ensure the infotainment master controller is configured with the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B14AC-11	Audio Amplifier Wake-up/Enable Control - Circuit short to ground	NOTE: Circuit reference - AMP WAKE UP - Audio amplifier module wake up circuit short circuit to ground	Refer to the electrical circuit diagrams and check the audio amplifier module wake up circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AC-15	Audio Amplifier Wake-up/Enable Control - Circuit short to battery or open	NOTE: Circuit reference - AMP WAKE UP - Audio amplifier module wake up circuit short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the audio amplifier module wake up circuit for short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AC-19	Audio Amplifier Wake-up/Enable Control - Circuit current above threshold	NOTE: Circuit reference - AMP WAKE UP - Audio amplifier module wake up circuit short circuit to ground Audio amplifier module internal failure Infotainment master controller internal failure	Refer to the electrical circuit diagrams and check the audio amplifier module wake up circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest If the speakers do not function normally, using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new audio amplifier module If the speakers function normally, using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller to the latest level software and retest. If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B14AD-02	Front Display Screen - General signal failure	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
B14AD-05	Front Display Screen - System programming failures	Interactive Display Module A (IDMA) programming failure Interactive Display Module A (IDMA) internal failure	Refer to the electrical circuit diagrams and check the integrity of the Interactive Display Module A (IDMA) power and ground circuits. Connect Jaguar Land Rover approved diagnostic equipment and check connections are secure before reconfiguring the Interactive Display Module A (IDMA). Clear DTCs and retest If fault persists, replace the Interactive Display Module A (IDMA)
B14AD-16	Front Display Screen - Circuit voltage below threshold	Interactive Display Module A (IDMA) power circuit short circuit to ground Battery/charging system fault	Refer to the electrical circuit diagrams and check the Interactive Display Module A (IDMA) power circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the relevant service information and check the battery and charging system
B14AD-17	Front Display Screen - Circuit voltage above threshold	Interactive Display Module A (IDMA) ground circuit short circuit to power Battery/charging system fault	Refer to the electrical circuit diagrams and check the Interactive Display Module A (IDMA) ground circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the relevant service information and check the battery and charging system
B14AD-31	Front Display Screen - No signal	Interactive Display Module A (IDMA) APIX link active with no video	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller to the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B14AD-49	Front Display Screen - Internal electronic failure	Interactive Display Module A (IDMA) internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new Interactive Display Module A (IDMA)
B14AD-96	Front Display Screen - Component internal failure	Interactive Display Module A (IDMA) internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new Interactive Display Module A (IDMA)
B14AD-98	Front Display Screen - Component or system over temperature	Interactive Display Module A (IDMA) internal temperature above threshold	Allow the system to cool. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new Interactive Display Module A (IDMA)
B14AD-9A	Front Display Screen - Component or system operating conditions	Interactive Display Module A (IDMA) internal temperature below threshold	NOTE: This DTC is for event information only and does not indicate a fault Allow the system to warm. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest
B14AE-02	Left Rear Display Screen - General signal failure	Rear left display screen APIX circuit short circuit to ground, short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the rear left display screen APIX circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AE-05	Left Rear Display Screen - System programming failures	Rear left display screen programming failure Rear left display screen internal failure	Refer to the electrical circuit diagrams and check the integrity of the rear left display screen power and ground circuits. Connect the manufacturer approved diagnostic tool and check connections are secure before reconfiguring the rear left display screen. Clear DTCs and retest If fault persists, replace the rear left display screen
B14AE-16	Left Rear Display Screen - Circuit voltage below threshold	Rear left display screen power circuit short circuit to ground Rear left display screen ground circuit short circuit to power	Refer to the electrical circuit diagrams and check the rear left display screen power circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the rear left display screen ground circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AE-17	Left Rear Display Screen - Circuit voltage above threshold	Rear left display screen ground circuit short circuit to power Battery/charging system fault	Refer to the electrical circuit diagrams and check the rear left display screen ground circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the relevant service information and check the battery and charging system
B14AE-31	Left Rear Display Screen - No signal	Rear left display screen APIX link active with no video	Using the Jaguar land rover approved diagnostic equipment, update the infotainment slave controller to the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment slave controller. Contact the Jaguar Land Rover service desk for further assistance
B14AE-96	Left Rear Display Screen - Component internal failure	Rear left display screen internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear left display screen
B14AE-98	Left Rear Display Screen - Component or system over temperature	Rear left display screen internal temperature above threshold	Allow the system to cool. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear left display screen
B14AE-9A	Left Rear Display Screen - Component or system operating conditions	Rear left display screen internal temperature below threshold	NOTE: This DTC is for event information only and does not indicate a fault Allow the system to warm. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest
B14AF-02	Right Rear Display Screen - General signal failure	Rear right display screen APIX circuit short circuit to ground, short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the rear right display screen APIX circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AF-05	Right Rear Display Screen - System programming failures	Rear right display screen programming failure Rear right display screen internal failure	Refer to the electrical circuit diagrams and check the integrity of the rear right display screen power and ground circuits. Connect the Jaguar Land Rover approved diagnostic equipment and check connections are secure before reconfiguring the rear right display screen. Clear DTCs and retest If fault persists, replace the rear right display screen
B14AF-16	Right Rear Display Screen - Circuit voltage below threshold	Rear right display screen power circuit short circuit to ground Rear right display screen ground circuit short circuit to power	Refer to the electrical circuit diagrams and check the rear right display screen power circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the rear right display screen ground circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14AF-17	Right Rear Display Screen - Circuit voltage above threshold	Rear right display screen ground circuit short circuit to power Battery/charging system fault	Refer to the electrical circuit diagrams and check the rear right display screen ground circuit for short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the relevant service information and check the battery and charging system
B14AF-31	Right Rear Display Screen - No signal	Rear right display screen APIX link active with no video	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment slave controller to the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment slave controller. Contact the Jaguar Land Rover service desk for further assistance
B14AF-96	Right Rear Display Screen - Component internal failure	Rear right display screen internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear right display screen
B14AF-98	Right Rear Display Screen - Component or system over temperature	Rear right display screen internal temperature above threshold	Allow the system to cool. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear right display screen
B14AF-9A	Right Rear Display Screen - Component or system operating conditions	Rear right display screen internal temperature below threshold	NOTE: This DTC is for event information only and does not indicate a fault Allow the system to warm. Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest
B14B0-11	Television Antenna #1 - Circuit short to ground	TV antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the TV antenna circuit for short circuit to ground
B14B0-12	Television Antenna #1 - Circuit short to battery	TV antenna circuit short circuit to power	Refer to the electrical circuit diagrams and check the TV antenna circuit for short circuit to power
B14B0-13	Television Antenna #1 - Circuit open	TV antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the TV antenna circuit for open circuit, high resistance
B14B1-11	Television Antenna #2 - Circuit short to ground	TV antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the TV antenna circuit for short circuit to ground
B14B1-12	Television Antenna #2 - Circuit short to battery	TV antenna circuit short circuit to power	Refer to the electrical circuit diagrams and check the TV antenna circuit for short circuit to power
B14B1-13	Television Antenna #2 - Circuit open	TV antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the TV antenna circuit for open circuit, high resistance
B14B2-11	Television Antenna #3 - Circuit short to ground	TV antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the TV antenna circuit for short circuit to ground
B14B2-12	Television Antenna #3 - Circuit short to battery	TV antenna circuit short circuit to power	Refer to the electrical circuit diagrams and check the TV antenna circuit for short circuit to power
B14B2-13	Television Antenna #3 - Circuit open	TV antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the TV antenna circuit for open circuit, high resistance
B14B3-11	Television Antenna #4 - Circuit short to ground	TV antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the TV antenna circuit for short circuit to ground
B14B3-12	Television Antenna #4 - Circuit short to battery	TV antenna circuit short circuit to power	Refer to the electrical circuit diagrams and check the TV antenna circuit for short circuit to power
B14B3-13	Television Antenna #4 - Circuit open	TV antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the TV antenna circuit for open circuit, high resistance
B14B4-15	Bluetooth Antenna #1 - Circuit short to battery or open	Infotainment master controller front Bluetooth® antenna circuit short circuit to power, open circuit, high resistance Infotainment slave controller (where fitted) rear Bluetooth® antenna circuit short circuit to power, open circuit, high resistance	NOTE: If this DTC is logged simultaneously with a cluster of DTCs including U200F-11, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the infotainment master controller front Bluetooth® antenna circuit for short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) rear Bluetooth® antenna circuit for short circuit to power, open circuit, high resistance
B14B5-15	WiFi Antenna #1 - Circuit short to battery or open	WiFi antenna circuit short circuit to power, open circuit, high resistance	NOTE: If this DTC is logged simultaneously with a cluster of DTCs including U200F-11, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the WiFi antenna circuit for short circuit to power, open circuit, high resistance
B14B6-13	USB Port #1 - Circuit open	NOTE: Circuit reference - UIPUSB 2.0 D+/UIPUSB 2.0 D-/UIP USB 3.0 SSTX+/UIP USB 3.0 SSTX-/UIP USB 3.0 SSRX+/UIP USB 3.0 SSRX- - Infotainment master controller USB repeater module data circuit open circuit, high resistance Infotainment slave controller (where fitted) rear USB repeater module data circuit open circuit, high resistance	NOTE: This DTC will also be logged if the USB cable is disconnected between the infotainment master controller and USB repeater module (where fitted). If the cable between the USB repeater module and the user interface panel is disconnected DTC B14A3-02 will be logged Refer to the electrical circuit diagrams and check the infotainment master controller USB repeater module data circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) rear USB repeater module data circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14B6-19	USB Port #1 - Circuit current above threshold	NOTE: Circuit reference - UIP VBUS - Infotainment master controller USB repeater module power circuit short circuit to ground, short circuit to power Infotainment slave controller (where fitted) rear USB repeater module power circuit short circuit to ground, short circuit to power	Refer to the electrical circuit diagrams and check the infotainment master controller USB repeater module power circuit for short circuit to ground, short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new USB repeater module Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) rear USB repeater module power circuit for short circuit to ground, short circuit to power. Repair or replace wiring harness as necessary, clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new rear USB repeater module
B14B7-13	USB Hub #1 - Circuit open	NOTE: Circuit reference - USB HUB 2.0 D+/USB HUB 2.0 D- - USB hub module data circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the USB hub module data circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14B7-19	USB Hub #1 - Circuit current above threshold	NOTE: Circuit reference - USB HUB VBUS - USB hub module power circuit short circuit to ground	Refer to the electrical circuit diagrams and check the USB hub module power circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new USB hub #1 module
B14B8-08	BroadR-Reach Link - Infotainment Slave - Link #2 (+) - Bus signal/message failures	Infotainment slave controller BroadR-Reach® Link #2 circuit short circuit between positive and negative	Refer to the electrical circuit diagrams and check the infotainment slave controller BroadR-Reach® Link #2 circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14B8-13	BroadR-Reach Link - Infotainment Slave - Link #2 (+) - Circuit open	Infotainment slave controller BroadR-Reach® Link #2 circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment slave controller BroadR-Reach® Link #2 circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B14D1-05	SDARS (Satellite Radio) Tuner - System programming failures	Infotainment master controller is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest
B14D1-96	SDARS (Satellite Radio) Tuner - Component internal failure	Infotainment master controller hardware/software incompatibility Infotainment master controller internal failure	NOTE: This DTC may log as a result of hardware/software incompatibility and may not indicate a fault in the vehicle Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest If the fault persists or the customer continues to report problems with the radio, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B14D2-05	TV (Television) - System programming failures	Infotainment master controller is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest
B14D2-56	TV (Television) - Invalid/incomplete configuration	Infotainment master controller is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest
B14D2-57	TV (Television) - Invalid/incomplete software component	Infotainment master controller is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest
B14D2-96	TV (Television) - Component internal failure	Infotainment master controller hardware/software incompatibility Infotainment master controller internal failure	NOTE: This DTC may log as a result of hardware/software incompatibility and may not indicate a fault in the vehicle Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest If the fault persists or the customer continues to report problems with the TV, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B14D3-05	Radio Tuner - System programming failures	Infotainment master controller is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest
B14D3-56	Radio Tuner - Invalid/incomplete configuration	Infotainment master controller is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest
B14D3-96	Radio Tuner - Component internal failure	Infotainment master controller hardware/software incompatibility Infotainment master controller internal failure	NOTE: This DTC may log as a result of hardware/software incompatibility and may not indicate a fault in the vehicle Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest If the fault persists or the customer continues to report problems with the radio, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B14D9-11	Dedicated Short Range Communication (DRSC) Antenna - Circuit short to ground	Dedicated short range communication module antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the dedicated short range communication module antenna circuit for short circuit to ground
B14D9-13	Dedicated Short Range Communication (DRSC) Antenna - Circuit open	Dedicated short range communication module antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the dedicated short range communication module antenna circuit for open circuit, high resistance
B14DA-11	Vehicle Information and Communication System (VICS) Antenna - Circuit short to ground	Vehicle information and communication system module antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the vehicle information and communication system module antenna circuit for short circuit to ground
B14DA-13	Vehicle Information and Communication System (VICS) Antenna - Circuit open	Vehicle information and communication system module antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the vehicle information and communication system module antenna circuit for open circuit, high resistance
B14DB-56	Optical Disk Drive (ODD) Region Code - Invalid/incomplete configuration	Digital disc player region code incorrect for region	Set region code to current region
B14DC-13	Electronic Toll Collection Module - Circuit open	Electronic toll collection module connection not available	Refer to the electrical circuit diagrams and check the electronic toll collection module power and ground circuits for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest
B14DC-96	Electronic Toll Collection Module - Component internal failure	Electronic toll collection module internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new electronic toll collection module
B151F-09	Auxiliary Cooling Fan - Component failure	Infotainment cooling fan circuit open circuit, high resistance Infotainment cooling fan duct obstructed or installed incorrectly Infotainment cooling fan internal failure	Refer to the electrical circuit diagrams and check the infotainment cooling fan circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Check the integrity of the infotainment cooling fan duct Check the operation of the infotainment cooling fan. Install a new infotainment cooling fan as necessary
B1520-11	Auxiliary Fan Relay Control Line - Circuit short to ground	Infotainment cooling fan relay circuit short circuit to ground	Refer to the electrical circuit diagrams and check the infotainment cooling fan relay circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest
B1520-13	Auxiliary Fan Relay Control Line - Circuit open	NOTE: This DTC will log in Service 19 Only after On Demand Self Test is run Infotainment cooling fan relay circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment cooling fan relay circuit for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B1968-02	Lower Front Display Screen - General signal failure	Interactive Control Display Module (ICDM) APIX circuit short circuit to ground, short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the Interactive Control Display Module (ICDM) APIX circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
B1A56-11	Antenna - Circuit short to ground	AM/FM antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the AM/FM antenna circuit for short circuit to ground
B1A56-12	Antenna - Circuit short to battery	AM/FM antenna circuit short circuit to power	Refer to the electrical circuit diagrams and check the AM/FM antenna circuit for short circuit to power
B1A56-13	Antenna - Circuit open	AM/FM antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the AM/FM antenna circuit for open circuit, high resistance
B1A89-11	Satellite Antenna - Circuit short to ground	Satellite radio antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the satellite radio antenna circuit for short circuit to ground
B1A89-13	Satellite Antenna - Circuit open	Satellite radio antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the satellite radio antenna circuit for open circuit, high resistance
B1D55-11	Antenna #2 - Circuit short to ground	FM antenna circuit short circuit to ground	Refer to the electrical circuit diagrams and check the FM antenna circuit for short circuit to ground
B1D55-12	Antenna #2 - Circuit short to battery	FM antenna circuit short circuit to power	Refer to the electrical circuit diagrams and check the FM antenna circuit for short circuit to power
B1D55-13	Antenna #2 - Circuit open	FM antenna circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check the FM antenna circuit for open circuit, high resistance
B1D99-19	Solid State Drive - Circuit current above threshold	Infotainment master controller hard drive internal failure	Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new infotainment master controller
B1D99-98	Solid State Drive - Component or system over temperature	Infotainment master controller hard drive over temperature Infotainment master controller hard drive internal failure	Allow the system to cool. Using the Jaguar Land Rover approved diagnostic equipment, ensure the infotainment master controller is configured with the latest level software level If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B1DE3-2F	Multimedia Link - Driver assistance domain controller - Signal erratic	Infotainment master controller signal circuit short circuit to ground, short circuit to power, open circuit, high resistance Infotainment master controller power or ground circuit open circuit, high resistance	Check for loose/damaged connectors, corroded or backed out terminals. Refer to the electrical circuit diagrams and check the infotainment master controller signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the cable continuity for both cables between the infotainment master controller to image processing module B and image processing module B to camera module. Replace cables as required If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance Check for loose/damaged connectors, corroded or backed out terminals. Refer to the electrical circuit diagrams and check the infotainment master controller power and ground circuits for open circuit, high resistance Refer to the electrical circuit diagrams and check the cable continuity for both cables between the infotainment master controller to image processing module B and image processing module B to camera module. Replace cables as required If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B1DE3-31	Multimedia Link - Driver assistance domain controller - No signal	Infotainment master controller signal circuit short circuit to ground, short circuit to power, open circuit, high resistance Infotainment master controller power or ground circuit open circuit, high resistance	Check for loose/damaged connectors, corroded or backed out terminals. Refer to the electrical circuit diagrams and check the infotainment master controller signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the cable continuity for both cables between the infotainment master controller to image processing module B and image processing module B to camera module. Replace cables as required If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance Check for loose/damaged connectors, corroded or backed out terminals. Refer to the electrical circuit diagrams and check the infotainment master controller power and ground circuits for open circuit, high resistance Refer to the electrical circuit diagrams and check the cable continuity for both cables between the infotainment master controller to image processing module B and image processing module B to camera module. Replace cables as required If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
B1DE3-67	Multimedia Link - Driver assistance domain controller - Signal incorrect after event	Infotainment master controller signal circuit short circuit to ground, short circuit to power, open circuit, high resistance Infotainment master controller power or ground circuit open circuit, high resistance	Check for loose/damaged connectors, corroded or backed out terminals. Refer to the electrical circuit diagrams and check the infotainment master controller signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance Refer to the electrical circuit diagrams and check the cable continuity for both cables between the infotainment master controller to image processing module B and image processing module B to camera module. Replace cables as required If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance Check for loose/damaged connectors, corroded or backed out terminals. Refer to the electrical circuit diagrams and check the infotainment master controller power and ground circuits for open circuit, high resistance Refer to the electrical circuit diagrams and check the cable continuity for both cables between the infotainment master controller to image processing module B and image processing module B to camera module. Replace cables as required If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
U0001-82	High Speed CAN Communication Bus - Alive/sequence counter incorrect/not updated	Invalid data received from another control module via the high speed CAN bus (comfort)	Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the invalid data source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-87	High Speed CAN Communication Bus - Missing message	Missing message from another control module via the high speed CAN bus (comfort)	Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the missing message source control module. Check the relevant control module for related DTCs and refer to the relevant DTC index
U0001-88	High Speed CAN Communication Bus - Bus off	High speed CAN bus (comfort) circuit short circuit to ground, short circuit to power, open circuit, high resistance	Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the electrical circuit diagrams and check the high speed CAN bus (comfort) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
U0184-00	Lost Communication With Radio - No sub type information	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
U0300-00	Internal Control Module Software Incompatibility - No sub type information	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the DTCs Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the DTCs and retest
U1011-13	Optical Disk Drive - Circuit open	Digital disc player power or ground circuit open circuit, high resistance Digital disc player internal failure	NOTE: If this DTC is logged simultaneously with a cluster of DTCs including U200F-11, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the digital disc player power and ground circuits for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest. If the fault persists, install a new digital disc player
U1014-02	APIX Display Link - User Interface Panel - Link #2 - General signal failure	Infotainment slave controller rear portable audio interface panel APIX circuit 2 open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment slave controller rear portable audio interface panel APIX circuit 2 for open circuit, high resistance
U1014-31	APIX Display Link - User Interface Panel - Link #2 - No signal	Infotainment slave controller rear portable audio interface panel APIX circuit 2 open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment slave controller rear portable audio interface panel APIX circuit 2 for open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
U200E-11	Control Module Output Power B - Circuit short to ground	NOTE: Infotainment master controller circuit reference - USB HUB PWR/USB HUB GND - Infotainment slave controller circuit reference - R_HLDR_POWER - Infotainment master controller USB hub circuit short circuit to ground Infotainment slave controller (where fitted) rear right display screen circuit short circuit to ground	Refer to the electrical circuit diagrams and check the infotainment master controller USB hub circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) rear right display screen circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest
U200E-15	Control Module Output Power B - Circuit short to battery or open	NOTE: Infotainment master controller circuit reference - USB HUB PWR/USB HUB GND - Infotainment slave controller circuit reference - R_HLDR_POWER - Infotainment master controller USB hub circuit short circuit to power, open circuit, high resistance Infotainment slave controller (where fitted) rear right display screen circuit short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment master controller USB hub circuit for short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) rear right display screen circuit for short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
U200F-11	Control Module Output Power C - Circuit short to ground	Infotainment slave controller (where fitted) rear left display screen circuit short circuit to ground	NOTE: This fault may also cause a number of other DTCs to log (B1492-11, B1492-12, B1492-13, B14AD-02, B14B4-15, B14B5-15, U1011-13). If this DTC is logged simultaneously with a cluster of other DTCs, check symptoms for U200F-11 first, rectify the fault, clear DTCs and retest Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) rear left display screen circuit for short circuit to ground. Repair or replace wiring harness as necessary, clear the DTCs and retest
U200F-15	Control Module Output Power C - Circuit short to battery or open	NOTE: Infotainment master controller circuit reference - HLDF APIX2 12V - Infotainment slave controller circuit reference - L_HLDR_POWER - Infotainment slave controller (where fitted) rear left display screen circuit short circuit to power, open circuit, high resistance	Refer to the electrical circuit diagrams and check the infotainment slave controller (where fitted) rear left display screen circuit for short circuit to power, open circuit, high resistance. Repair or replace wiring harness as necessary, clear the DTCs and retest
U2016-68	Control Module Main Software - Event Information	Infotainment master controller is not configured correctly	NOTE: If DTCs B14B4-15, B14B5-15 and B1492-11 are logged in the infotainment master controller alongside this DTC, this does not indicate a fault with the associated DTCs This DTC may set due to a hardware/software reset and may not indicate a fault in the vehicle Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
U2100-55	Initial Configuration Not Complete - Not configured	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
U2300-51	Central Configuration - Not programmed	Change to car configuration file has been detected Infotainment master controller is not configured correctly	NOTE: This DTC will be logged if the car configuration file in the vehicle has been changed Using the Jaguar Land Rover approved diagnostic equipment, perform routine - In Control Touch Pro variant configuration Clear the DTCs, cycle ignition twice, wait for 3 minutes and retest If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance
U2300-54	Central Configuration - Missing calibration	Infotainment master controller is not configured correctly	NOTE: This DTC will log if the routine to clear the car configuration has been performed and subsequent correct steps are not complete. It will also occur if the car configuration has been partly updated Using the Jaguar Land Rover approved diagnostic equipment, ensure the process to reconfigure the module is complete. Clear the DTCs, then read DTCs in the next ignition cycle
U2300-55	Central Configuration - Not configured	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
U2300-56	Central Configuration - Invalid/incomplete configuration	See note	NOTE: This DTC is for event information only and does not indicate a fault Ignore this DTC
U2300-64	Central Configuration - Signal plausibility failure	Infotainment master controller is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller with the latest level software. Clear the DTCs and retest
U3000-04	Control Module - System internal failures	Infotainment master controller internal failure Infotainment slave controller (where fitted) internal failure	NOTE: If DTCs B14B4-15, B14B5-15 and B1492-11 are logged in the infotainment master controller alongside this DTC, this does not indicate a fault with the associated DTCs If DTC B14B4-15 or B14B5-15 is logged in the infotainment slave controller alongside this DTC, this does not indicate a fault with the associated DTCs Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment master controller to the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance Using the Jaguar Land Rover approved diagnostic equipment, update the infotainment slave controller to the latest level software. Clear the DTCs and retest If the fault persists, do not replace the infotainment slave controller. Contact the Jaguar Land Rover service desk for further assistance
U3000-98	Control Module - Component or system over temperature	Infotainment master controller internal temperature above threshold Infotainment slave controller (where fitted) internal temperature above threshold	Allow the system to cool. Using the Jaguar Land Rover approved diagnostic equipment, ensure the infotainment master controller is configured with the latest level software level If the fault persists, do not replace the infotainment master controller. Contact the Jaguar Land Rover service desk for further assistance Allow the system to cool. Using the Jaguar Land Rover approved diagnostic equipment, ensure the infotainment slave controller is configured with the latest level software level If the fault persists, do not replace the infotainment slave controller. Contact the Jaguar Land Rover service desk for further assistance