Instrument Panel Cluster (IPC)

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.

NOTE:

Guided Diagnostics must be followed and the repair advised by the process completed. Failure to do so may result in the rejection of any warranty claim made.
If a control module or a component is at fault and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the Jaguar Land Rover approved diagnostic equipment).
When performing voltage or resistance tests, always use a digital multimeter that has the resolution ability to view 3 decimal places. For example, on the 2 volts range can measure 1 mV or 2 K Ohm range can measure 1 Ohm. When testing resistance always take the resistance of the digital multimeter leads into account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
If Diagnostic Trouble Code(s) are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.
Check the JLR claims submission system for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific customer complaint and complete the recommendations as required.

The article below lists all Diagnostic Trouble Code(s) that could be set. For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing article in the repair information. For additional information, Refer to: INSTRUMENT CLUSTER

DTC	DESCRIPTION	POSSIBLE CAUSES	ACTION
B1009-51	Ignition Authorization - Not programed	Instrument cluster power or ground circuit open circuit, high resistance Instrument cluster is not configured correctly High speed CAN bus (chassis) circuit short circuit to ground, short circuit to power, open circuit, high resistance Instrument cluster internal failure	Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Power Supply Voltage (0xD111). Refer to the appropraite system wiring diagrams and check the instrument cluster power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Using the Jaguar Land Rover approved diagnostic equipment, perform routine - Write Security Target ID (7006) Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the appropraite system wiring diagrams and check the high speed CAN bus (chassis) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
B1009-87	Ignition Authorization - Missing message	Instrument cluster power or ground circuit open circuit, high resistance Central junction box power or ground circuit open circuit, high resistance High speed CAN bus (chassis)) circuit short circuit to ground, short circuit to power, open circuit, high resistance Instrument cluster internal failure	Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Power Supply Voltage (0xD111). Refer to the appropraite system wiring diagrams and check the instrument cluster power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Refer to the appropraite system wiring diagrams and check the central junction box power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the appropraite system wiring diagrams and check the high speed CAN bus (chassis) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
B100D-64	Column lock Authorization - Signal plausibility failure - Unable to unlock (engine start) or lock steering column lock	NOTE: This DTC is set when an Electric Steering Column Lock (ESCL) unlock request is received when the engine speed is greater than 400RPM or vehicle speed is greater than 1Kph or either signal is missing Instrument cluster (IC) power or ground circuit open circuit, high resistance ESCL control module power or ground circuit open circuit, high resistance High speed CAN bus (chassis) circuit short circuit to ground, short circuit to power, open circuit, high resistance	Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Power Supply Voltage (0xD111). Refer to the appropraite system wiring diagrams and check the instrument cluster power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Refer to the appropraite system wiring diagrams and check the Electric Steering Column Lock (ESCL) control module power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN network integrity test. Refer to the appropraite system wiring diagrams and check the high speed CAN bus (chassis) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest
B100E-64	Video Input "A" - Signal plausibility failure	APIX2 circuit short circuit to ground, short circuit to power, open circuit, high resistance Infotainment Master Controller fault Instrument cluster internal failure	NOTE: This DTC may be stored even though no fault condition is present and should be ignored unless the customer has reported an infotainment system concern. If the customer has reported an infotainment problem, clear the DTC and retest. Verify the customer concern prior to diagnosis Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, refer to the appropraite system wiring diagrams and check the APIX2 circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest Using the Jaguar Land Rover approved diagnostic equipment, check the infotainment master controller for related Diagnostic Trouble Code(s) and refer to the relevant DTC index Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
B1026-12	Steering Column Lock - Vehicle will not start or crank - Unable to unlock or lock steering column lock	Electric steering column lock (ESCL) control circuit short circuit to power Electric steering column lock (ESCL) ground circuit open circuit, high resistance	NOTE: Output is not driven if DTC B9026-63 is set, DTC B1026-63 must be cleared before testing for B1026-12 Using the Jaguar Land Rover approved diagnostic equipment, check for related Diagnostic Trouble Code(s) and refer to the relevant DTC index. Rectify before continuing Refer to the appropraite system wiring diagrams and check the electric steering column lock (ESCL) control circuit for short circuit to power. Repair circuit as required, clear DTC and retest Refer to the appropraite system wiring diagrams and check the electric steering column lock ground circuit for open circuit, high resistance. Repair circuit as required, clear DTC and retest
B1026-63	Steering Column Lock - Vehicle will not start or crank - Unable to unlock or lock steering column lock	Circuit/component protection time-out. Electric steering column lock (ESCL) ground connection short to battery counter has incremented to the threshold and has latched OFF to protect the hardware from damage Electric steering column lock (ESCL) ground circuit short circuit to power	NOTE: Global DTC clear will not clear the DTC unless the counter is reset. The Instrument Cluster (IC) is unusable until the fault is cleared and the counter and DTC reset Check electric steering column lock (ESCL) ground connection to instrument cluster (IC) Refer to the appropraite system wiring diagrams and check the electric steering column lock (ESCL) ground circuit for short circuit to power. Repair circuit as required, clear DTC and retest DID/PID 1E7D Counter Reset can be used to reset the counter to 0 and re-allow operation of electric steering column lock (ESCL) switched ground. Each time the fault counter is reset to zero, the fault threshold is halved. This can be repeated until the fault counter reaches 1, after which the DTC can no longer be cleared
B108E-04	Display - System internal failures	Instrument cluster internal failure Display circuit fault	Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
B108E-46	Display - Calibration/parameter memory failure	Instrument cluster internal failure Display circuit fault	Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
B10B7-86	Rear Air Discharge Temperature - Signal invalid	Instrument cluster internal failure Internal temperature sensor circuit fault	Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
B115C-7A	Transfer Fuel Pump - Fluid leak or seal failure	NOTE: This DTC is currently calibrated out in Software and shall not be set Transfer pump circuit short circuit to ground, short circuit to power, open circuit, high resistance Transfer pump hose leaking or restricted	NOTE: This DTC is set when the fuel level sensor values indicate that insufficient fuel is being transferred from the passive side of the fuel tank to the active side Refer to the appropraite system wiring diagrams and check the transfer pump circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest Check the transfer hose for leaks and restrictions
B1A14-96	RCM Warning Lamp - Component internal failure	Instrument cluster internal failure Airbag warning indicator circuit	Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
B1A85-96	Ambient Light Sensor - Component internal failure	Instrument cluster internal light sensor failure	NOTE: This DTC may be stored even though no fault condition is present and should be ignored unless the customer has reported an instrument cluster brightness concern. If the customer has reported an interior illumination problem, clear the DTC and retest. Verify the customer concern prior to diagnosis Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
P0460-11	Fuel Level Sensor A Circuit - Circuit short to ground	Active fuel level sensor circuit short circuit to ground	Using the Jaguar Land Rover approved diagnostic equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index. Refer to the appropraite system wiring diagrams and check the active fuel level sensor circuit for short circuit to ground. Repair the wiring harness as necessary, clear the Diagnostic Trouble Code(s) and retest
P0460-15	Fuel Level Sensor A Circuit - Circuit short to battery or open	Active fuel level sensor circuit short circuit to power, open circuit, high resistance	Using the Jaguar Land Rover approved diagnostic equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index. Refer to the appropraite system wiring diagrams and check the active fuel level sensor circuit for short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary, clear the Diagnostic Trouble Code(s) and retest
P0607-4B	Control Module Performance - Over temperature	Vehicle is operating in a high temperature environment Instrument cluster internal failure	Check the instrument cluster display is still illuminated. Allow the instrument cluster to cool. Clear the DTC and retest. If fault persists, consider environmental conditions before condemning the instrument cluster
P060A-08	Internal Control Module Monitoring Processor Performance - Bus signal/message failures	Instrument cluster internal failure Internal communication fault	Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the instrument cluster with the latest level software. Clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
P0610-55	Control Module Vehicle Options Error - Not configured	Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the Diagnostic Trouble Code(s) Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the Diagnostic Trouble Code(s) and retest
P1346-11	Fuel Level Sensor B Circuit - Circuit short to ground	Passive fuel level sensor circuit short circuit to ground	Using the Jaguar Land Rover approved diagnostic equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index. Refer to the appropraite system wiring diagrams and check the passive fuel level sensor circuit for short circuit to ground. Repair the wiring harness as necessary, clear the Diagnostic Trouble Code(s) and retest
P1346-15	Fuel Level Sensor B Circuit - Circuit short to battery or open	Passive fuel level sensor circuit short circuit to power, open circuit, high resistance	Using the Jaguar Land Rover approved diagnostic equipment, check the body control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index. Refer to the appropraite system wiring diagrams and check the passive fuel level sensor circuit for short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary, clear the Diagnostic Trouble Code(s) and retest
U0046-87	High Speed CAN Communication Bus - Missing Message	Missing message from another control module through the high speed CAN bus (chassis)	Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the missing message source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0046-88	High Speed CAN Communication Bus - Bus Off	High speed CAN bus (chassis) circuit - Short circuit to ground, short circuit to power, open circuit, high resistance	Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN (chassis) network integrity test. Refer to the appropraite system wiring diagrams and check the high speed CAN bus (chassis) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest
U0055-87	High Speed CAN Communication Bus - Missing Message	Missing message from another control module through the high speed CAN bus (comfort)	Using the Jaguar Land Rover approved diagnostic equipment, check the snapshot data to determine the missing message source control module. Check the relevant control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0055-88	High Speed CAN Communication Bus - Bus Off	High speed CAN bus (comfort) circuit - Short circuit to ground, short circuit to power, open circuit, high resistance	Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN (comfort) network integrity test. Refer to the appropraite system wiring diagrams and check the high speed CAN bus (comfort) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest
U0300-00	Internal Control Module Software Incompatibility - No sub type information	Instrument cluster is not configured correctly	Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the instrument cluster with the latest level software Using the Jaguar Land Rover approved diagnostic equipment, check for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U0402-68	Invalid Data Received from TCM - Event information	Missing/invalid data from the transmission control module	Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control module for related Diagnostic Trouble Code(s) and refer to the relevant DTC index
U2013-02	Switch Pack - General signal failure	NOTE: No warning light is illuminated to indicate that the DTC is set, but the fault may cause illumination of a telltale, display of a message or failure of an information display as part of defined functionality under these conditions Interactive Display Module A (+IDMA) fault Steering wheel switchpack internal failure	Using Jaguar Land Rover approved diagnostic equipment, check the Interactive Display Module A (IDMA) for related Diagnostic Trouble Code(s) and refer to the relevant DTC index Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new steering wheel switchpack
U3000-46	Control Module - Calibration/parameter memory failure	Instrument cluster internal failure Odometer memory corrupted	NOTE: This DTC is only set as part of diagnostic self test routine 0202 This DTC indicates that the contents of non volatile memory containing the odometer have been corrupted or inconsistent, potentially due to an internal hardware failure Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
U3000-49	Control Module - Internal electronic failure	Instrument cluster internal failure Internal memory corrupted	NOTE: This DTC is only set as part of diagnostic self test routine 0202 This DTC indicates that the contents of non volatile memory containing the odometer have been corrupted or inconsistent, potentially due to an internal hardware failure Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the instrument cluster with the latest level software Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest. If the fault persists, install a new instrument cluster
U3000-55	Control Module - Not configured	Incorrect wheels/tires installed Tire size compensation is incorrectly configured	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the Diagnostic Trouble Code(s) Install the correct wheels and tires Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the Diagnostic Trouble Code(s) and retest
U3000-87	Control Module - Missing message	High speed CAN bus (comfort) circuit short circuit to ground, short circuit to power, open circuit, high resistance Car configuration file mismatch with vehicle specification	NOTE: After updating the car configuration file, set the ignition to on and wait 30 seconds before clearing the Diagnostic Trouble Code(s) Using the Jaguar Land Rover approved diagnostic equipment, perform a CAN (comfort) network integrity test. Refer to the appropraite system wiring diagrams and check the high speed CAN bus (comfort) circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair circuit as required, clear DTC and retest Using the Jaguar Land Rover approved diagnostic equipment, check and update the car configuration file as necessary. Clear the Diagnostic Trouble Code(s) and retest
U3002-81	Vehicle Identification Number - Invalid serial data received	Instrument cluster previously installed on another vehicle New instrument cluster installed and VIN not yet programed	Install the original or a new instrument cluster as necessary Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) and retest
U3003-16	Battery Voltage - Circuit voltage below threshold	Instrument cluster power or ground circuit open circuit, high resistance Battery/charging system fault	Refer to the appropraite system wiring diagrams and check the instrument cluster power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Refer to the relevant article of the repair information and test the battery and charging system
U3003-17	Battery Voltage - Circuit voltage above threshold	Instrument cluster power or ground circuit open circuit, high resistance Battery/charging system fault	Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - ECU Power Supply Voltage (0xD111). Refer to the appropraite system wiring diagrams and check the instrument cluster power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest Refer to the relevant article of the repair information and check the battery and charging system
U3003-62	Battery Voltage - Signal compare failure	Mismatch between the voltage at the instrument cluster and the voltage value broadcast on the CAN bus	Refer to the appropraite system wiring diagrams and check the instrument cluster power and ground circuits for open circuit, high resistance. Repair circuit as required, clear DTC and retest