Inspection Procedure

HINT:

If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may be open.
Read freeze frame data using the hand-held tester or the OBD II scan tool. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean or rich, etc. at the time of the malfunction.

READ VALUE OF HAND-HELD TESTER OR OBD II SCAN TOOL (INTAKE AIR TEMPERATURE)
1. Connect the hand-held tester or the OBD II scan tool to the DLC3.
2. Turn the ignition switch ON and push the hand-held tester or the OBD II scan tool main switch ON.
3. Select the item "DIAGNOSIS/ENHANCED OBD II/DATA LIST/ALL/INTAKE AIR" and read its value displayed on the hand-held tester or the OBD II scan tool.
  Temperature: Same value as the actual intake air temperature.
  
  Result:
  
  Fig 1: Result Description Chart
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
HINT:
- If there is an open circuit, the hand-held tester or the OBD II scan tool indicates -40°C (-40°F).
- If there is a short circuit, the hand-held tester or the OBD II scan tool indicates 140°C (284°F) or more.
1. A: GO TO NEXT STEP.
2. B: Go to step 4
3. C: CHECK FOR INTERMITTENT PROBLEMS (See PRE-CHECK )
READ VALUE OF HAND-HELD TESTER OR OBD II SCAN TOOL (CHECK FOR OPEN IN WIRE HARNESS)
1. Disconnect the M1 mass air flow sensor connector.
2. Connect terminals THA and E2 of the mass air flow sensor wire harness side connector.
  
  Fig 2: Identifying MAF Sensor Connector Terminals
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Fig 3: Connecting Terminals THA And E2 Of Mass Air Flow Sensor Wire Harness Side Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Turn the ignition switch ON.
4. Select the item "DIAGNOSIS/ENHANCED OBD II/DATA LIST/ALL/INTAKE AIR" and read its value displayed on the hand-held tester or the OBD II scan tool.
  Temperature value: 140°C (284°F) or more
5. Reconnect the mass air flow sensor connector.
1. OK: CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE MASS AIR FLOW SENSOR
2. NG: GO TO NEXT STEP.
READ VALUE OF HAND-HELD TESTER OR OBD II SCAN TOOL (CHECK FOR OPEN IN ECM)
1. Disconnect the M1 mass air flow sensor connector.
2. Connect terminals THA and E2 of the E8 ECM connector.
  
  Fig 4: Connecting Terminals THA And E2 Of E8 ECM Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Fig 5: Identifying ECM E8 Connector Terminals
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  Before checking, do a visual and contact pressure check for the ECM connector.
3. Turn the ignition switch ON.
4. Select the item "DIAGNOSIS/ENHANCED OBD II/DATA LIST/ALL/INTAKE AIR" and read its value displayed on the hand-held tester or the OBD II scan tool.
  Temperature value: 140°C (284°F) or more
5. Reconnect the mass air flow sensor connector.
1. OK: REPAIR OR REPLACE HARNESS OR CONNECTOR
2. NG: CONFIRM GOOD CONNECTION AT ECM. IF OK, REPLACE ECM (See REPLACEMENT in ENGINE CONTROL SYSTEM )
READ VALUE OF HAND-HELD TESTER OR OBD II SCAN TOOL (CHECK FOR SHORT IN WIRE HARNESS)
1. Disconnect the M1 mass air flow sensor connector.
  
  Fig 6: Disconnecting M1 MAF Sensor Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Turn the ignition switch ON.
3. Select the item "DIAGNOSIS/ENHANCED OBD II/DATA LIST/ALL/INTAKE AIR" and read its value displayed on the hand-held tester or the OBD II scan tool.
  Temperature value: -40°C (-40°F)
4. Reconnect the mass air flow sensor connector.
1. OK: REPLACE MASS AIR FLOW SENSOR
2. NG: GO TO NEXT STEP.
READ VALUE OF HAND-HELD TESTER OR OBD II SCAN TOOL (CHECK FOR SHORT IN ECM)
1. Disconnect the E8 ECM connector.
2. Turn the ignition switch ON.
3. Select the item "DIAGNOSIS/ENHANCED OBD II/DATA LIST/ALL/INTAKE AIR" and read its value displayed on the hand-held tester or the OBD II scan tool.
  Temperature value: -40°C (-40°F)
4. Reconnect the ECM connector.
  
  Fig 7: Connecting Mass Air Flow Sensor Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Fig 8: Identifying ECM E8 Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. OK: REPAIR OR REPLACE HARNESS OR CONNECTOR
2. NG: REPLACE ECM (See REPLACEMENT in ENGINE CONTROL SYSTEM )