LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2006 >> GS 430 >> Repair and Diagnosis (Single Page) >> Brakes >> Brakes Control Systems >> Brake Control >> Vehicle Stability Control System >> DTC C0200/31 Front Speed Sensor RH Circuit; DTC C0205/32 Front Speed Sensor LH Circuit; DTC C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC); DTC C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) >> Wiring Diagram
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC C0200/31 Front Speed Sensor RH Circuit; DTC C0205/32 Front Speed Sensor LH Circuit; DTC C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC); DTC C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC): Wiring Diagram

Fig 1: Front Speed Sensor Circuit - Wiring Diagram
G04024977Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NOTE: When replacing the ABS and TRACTION actuator assembly, perform zero point calibration (See CHECK FOR INTERMITTENT PROBLEMS  ).

HINT:

Start the inspection from step 1 when using the intelligent tester and from step 3 when not using the intelligent tester.

  1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) 
    1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (See HOW TO PROCEED WITH TROUBLESHOOTING  ).

      DATA LIST: ABS/VSC 

      DATA LIST ABS/VSC

      Item (Display) Measurement Item / Range (Display) Normal Condition
      FR SPD OPN FR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal
      FL SPD OPN FL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal

      OK: 

      There are no momentary interruptions. 

      HINT:

      Perform the above inspection before removing the sensor and connector.

    NG : CHECK AND REPAIR HARNESS AND CONNECTOR (SPEED SENSOR CIRCUIT) 

    OK : Go to next step 

  2. READ VALUE OF INTELLIGENT TESTER (FRONT SPEED SENSOR) 
    1. Connect the intelligent tester to the DLC3.
    2. Start the engine.
    3. Select the DATA LIST mode on the intelligent tester.

      DATA LIST: ABS/VSC 

      DATA LIST ABS/VSC

      Item (Display) Measurement Item / Range (Display) Normal Condition
      FR WHEEL SPD Wheel speed sensor (FR) reading / min.: 0 mph (0 km/h, max.: 202 mph (326 km/h)) Actual wheel speed
      FL WHEEL SPD Wheel speed sensor (FL) reading /min.: 0 mph (0 km/h, max.: 202 mph (326 km/h)) Actual wheel speed
    4. Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

      OK: 

      The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed. 

      DATA LIST: ABS/VSC 

      DATA LIST ABS/VSC

      Item (Display) Measurement Item / Range (Display) Normal Condition
      FR WHEEL DIR Wheel direction (FR) / FORWARD or BACK FORWARD: Forward BACK: Back
      FL WHEEL DIR Wheel direction (FL) / FORWARD or BACK FORWARD: Forward BACK: Back
    5. Check that the sensor signal conforms to the wheel direction.

      OK: 

      The wheel direction is displayed. 

    NG : Go to step   5 

    OK : Go to next step 

  3. PERFORM TEST MODE (SIGNAL CHECK) 
    1. Perform sensor signal check in TEST MODE PROCEDURE  .

      OK: 

      All test mode DTCs are erased. 

    NG : Go to step   5 

    OK : Go to next step 

  4. RECONFIRM DTC 
    1. Clear the DTC (See DTC CHECK / CLEAR  ).
    2. Start the engine.
    3. Drive the vehicle at the speed of 32 mph (20 km/h) or more for at least 60 seconds.
    4. Check that the same DTC is recorded (See DTC CHECK / CLEAR  ).

      Result 

      RESULT REFERENCE

      Display (DTC Output) Proceed To
      DTCs (C0200/31 and C0205/32) are not output A
      DTCs (C0200/31 and C0205/32) are output B

      HINT:

      • It is suspected that the DTCs were output due to a bad connection of the connector terminal.
      • If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step (See PROBLEM SYMPTOMS TABLE  ).

    B : Go to step   11 

    A : END 

  5. INSPECT FRONT SPEED SENSOR INSTALLATION 
    1. Check the speed sensor installation.

      OK (2WD): 

      There is no clearance between the sensor and the front steering knuckle. 

      OK (4WD): 

      There is no clearance between the sensor and the front steering knuckle. 

      The installation bolt is tightened properly. 

      Torque: 

      8.5 N*m (87 kgf*cm, 75 in.*lbf) 

      NOTE: Check the speed sensor signal after the replacement (See TEST MODE PROCEDURE  ).
      Fig 2: Identifying Speed Sensor Installation
      G04024978Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : CHECK AND REPLACE FRONT SPEED SENSOR 

    OK : Go to next step 

  6. INSPECT SPEED SENSOR TIP 
    1. Remove the front speed sensor (See DISASSEMBLY  or BRAKE CONTROL FRONT SPEED SENSOR (FOR 4WD)  ).
    2. Check the sensor tip.

      OK: 

      No scratches or foreign matter on the sensor tip. 

      NOTE: Check the speed sensor signal after the cleaning/replacement (See TEST MODE PROCEDURE  ).

    NG : CLEAN OR REPLACE SPEED SENSOR 

    OK : Go to next step 

  7. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE) 
    1. Disconnect the skid control sensor wire.
    2. Measure the resistance according to the value(s) in the table below.

      Resistance: 

      RH 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      h1 ("A"-2) - h1 ("B"-1) Below 1 Ω
      h1 ("A"-2) - h1 ("B"-2) 10 kΩ or higher
      h1 ("A"-2) - Body ground 10 kΩ or higher
      h1 ("A"-1) - h1 ("B"-2) Below 1 Ω
      h1 ("A"-1) - h1 ("B"-1) 10 kΩ or higher
      h1 ("A"-1) - Body ground 10 kΩ or higher

      LH 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      i1 ("A"-2) - i1 ("B"-1) Below 1 Ω
      i1 ("A"-2) - i1 ("B"-2) 10 kΩ or higher
      i1 ("A"-2) - Body ground 10 kΩ or higher
      i1 ("A"-1) - i1 ("B"-2) Below 1 Ω
      i1 ("A"-1) - i1 ("B"-1) 10 kΩ or higher
      i1 ("A"-1) - Body ground 10 kΩ or higher
      NOTE: Check the speed sensor signal after replacement (See TEST MODE PROCEDURE  ).
      Fig 3: Identifying Skid Control Sensor Connector
      G04024979Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : REPLACE SKID CONTROL SENSOR WIRE 

    OK : Go to next step 

  8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU TO FRONT SPEED SENSOR) 
    1. Disconnect the skid control ECU connector and the front speed sensor connector.
    2. Measure the resistance according to the value(s) in the table below.

      Resistance: 

      RH 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      A6-3 (FR+) - h1-2 (FR+) Below 1 Ω
      A6-17 (FR-) - h1-1 (FR-) Below 1 Ω

      LH 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      A6-18 (FL+) - i1-2 (FL+) Below 1 Ω
      A6-4 (FL-) - i1-1 (FL-) Below 1 Ω
    3. Measure the resistance according to the value(s) in the table below.

      Resistance: 

      RH 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      A6-3 (FR+) - Body ground 10 kΩ or higher
      A6-17 (FR-) - Body ground 10 kΩ or higher

      LH 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Specified Condition
      A6-18 (FL+) - Body ground 10 kΩ or higher
      A6-4 (FL-) - Body ground 10 kΩ or higher
      Fig 4: Identifying Skid Control ECU Connector And Front Speed Sensor Connector
      G04024980Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT) 

    OK : Go to next step 

  9. INSPECT FRONT SPEED SENSOR (INPUT VOLTAGE) 
    1. Disconnect the speed sensor connector.
    2. Turn the engine switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Voltage 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Condition Specified Condition
      h1-2 (FR+) - Body ground Engine switch on (IG) 7.5 to 12 V
      i1-2 (FL+) - Body ground Engine switch on (IG) 7.5 to 12 V
      Fig 5: Identifying Front Speed Sensor Connector
      G04024981Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY 

    OK : Go to next step 

  10. RECONFIRM DTC 
    1. Clear the DTC (See DTC CHECK / CLEAR  ).
    2. Start the engine.
    3. Drive the vehicle at the speed of 20 mph (32 km/h) or more for at least 60 seconds.
    4. Check that the same DTC is recorded (See DTC CHECK / CLEAR  ).

      HINT:

      Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.

      Result 

      RESULT REFERENCE

      Display (DTC Output) Proceed To
      DTCs (C0200/31 and C0205/32) are not output A
      DTCs (C0200/31 and C0205/32) are output B

      HINT:

      If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step (See PROBLEM SYMPTOMS TABLE  ).

    B : Go to step 11 

    A : END 

  11. REPLACE FRONT SPEED SENSOR 
    1. Replace the front speed sensor.
      NOTE: Check the speed sensor signal after replacement (See TEST MODE PROCEDURE  ).

    NEXT 

  12. RECONFIRM DTC 
    1. Clear the DTC (See DTC CHECK / CLEAR  ).
    2. Start the engine.
    3. Drive the vehicle at the speed of 20 mph (32 km/h) or more for at least 60 seconds.
    4. Check that the same DTC is recorded (See DTC CHECK / CLEAR  ).

      HINT:

      Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.

Result 

RESULT REFERENCE

Display (DTC Output) Proceed To
DTCs (C0200/31 and C0205/32) are not output A
DTCs (C0200/31 and C0205/32) are output B

B : REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY 

A : END 

scientia non olet · About LEMON Manuals