LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2010 >> IS 250C Standard >> Repair and Diagnosis (Single Page) >> Steering >> Steering Column >> Power Tilt & Telescopic Steering Column (Diagnostics - Introduction) >> Power Tilt And Power Telescopic Steering Column System >> Freeze Frame Data >> Freeze Frame Data
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Freeze Frame Data

  1. FREEZE FRAME DATA 
    1. Turn the engine switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the engine switch on (IG).
    4. Turn the Techstream on.
    5. Check the freeze frame data. Enter the following menus: Chassis / Tilt&Telescopic / Trouble Codes.
      TILT&TELESCOPIC

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Tilt Position Current tilt position data/
      Min.: 0
      Max.: 65535      		 7000 to 9000 H
      (28672 to 36864 edge)      		 -
      Telesco Position Current telescopic position data/
      Min.: 0
      Max.: 65535      		 7000 to 9000 H
      (28672 to 36864 edge)      		 -
      Up Switch Input state of tilt up by manual switch/
      OFF or ON      		 OFF: Tilt up is not activated by manual switch
      ON: Tilt up is activated by manual switch      		 -
      Tilt Up SW(MPX) Communication state of tilt up input by manual switch/
      OFF or ON      		 OFF: Tilt up is not activated by manual switch
      ON: Tilt up is activated by manual switch      		 -
      Down Switch Input state of tilt down by manual switch/
      OFF or ON      		 OFF: Tilt down is not activated by manual switch
      ON: Tilt down is activated by manual switch      		 -
      Tilt Down SW(MPX) Communication state of tilt down input by manual switch/
      OFF or ON      		 OFF: Tilt down is not activated by manual switch
      ON: Tilt down is activated by manual switch      		 -
      Telesco Short Switch Input state of telescopic short by manual switch/
      OFF or ON      		 OFF: Telescopic short is not activated by manual switch
      ON: Telescopic short is activated by manual switch      		 -
      Telesco Short SW(MPX) Communication state of telescopic short input by manual switch/
      OFF or ON      		 OFF: Telescopic short is not activated by manual switch
      ON: Telescopic short is activated by manual switch      		 -
      Telesco Long Switch Input state of telescopic long by manual switch/
      OFF or ON      		 OFF: Telescopic long is not activated by manual switch
      ON: Telescopic long is activated by manual switch      		 -
      Telesco Long SW(MPX) Communication state of telescopic long input by manual switch/
      OFF or ON      		 OFF: Telescopic long is not activated by manual switch
      ON: Telescopic long is activated by manual switch      		 -
      T&T Manual SW Data Voltage data of manual switch/
      Min.: 0 V
      Max.: 5 V      		 Neutral position: Below 0.2 V
      Tilt up: 1.67 to 2.13 V
      Tilt down: 0.54 to 0.74 V
      Telescopic contract: 1.08 to 1.40 V
      Telescopic extend: 2.22 to 2.77 V      		 -
      Power Source Voltage Voltage data of power supply/
      Min.: 0 V
      Max.: 20 V      		 Actual power supply voltage
      11 to 14 V      		 -
      Freeze Speed Info Vehicle speed data/
      Min.: 0 Km
      Max.: 255 Km      		 Actual vehicle speed -
      IG Switch (MPX) Communication state of engine switch/
      OFF or ON      		 OFF: Communication is interrupted
      ON: Communication is normal      		 -
      IG Switch Input state of engine switch/
      OFF or ON      		 OFF: Input signal is interrupted
      ON: Input signal is normal      		 -
      Key Switch/MPX Communication state of key switch confirmation signal/
      OFF or ON      		 OFF: Communication is interrupted
      ON: Communication is normal      		 -
      Key Code Confirm(MPX) Communication state of key code confirmation signal/
      OFF or ON      		 OFF: Communication is interrupted
      ON: Communication is normal      		 -
      Receive from Meter Communication state of combination meter signal/
      OK or Interpt      		 OK: Communication is normal
      Interpt: Communication is interrupted      		 -
      Receive from Body Communication state of body ECU signal/
      OK or Interpt      		 OK: Communication is normal
      Interpt: Communication is interrupted      		 -
      Receive from Seat ECU Communication state of seat ECU signal/
      OK or Interpt      		 OK: Communication is normal
      Interpt: Communication is interrupted      		 -
      Receive from Combi Communication state of combination switch ECU signal/
      OK or Interpt      		 OK: Communication is normal
      Interpt: Communication is interrupted      		 -
      Power ECU Info Communication state of power source control ECU signal/
      OK or Interpt      		 OK: Communication is normal
      Interpt: Communication is interrupted      		 -
scientia non olet · About LEMON Manuals