Rear Door RH Entry Lock Function does not Operate: Procedure

1. When the master switch assembly's door control switch is operated, check that the locked doors unlock.
   RESULT
   
   

   Result	Proceed to
   Door locks operate normally	OK
   Door locks do not operate normally	NG

NG → See step   10 

OK: Go to next step 

1. Using the Techstream, read the Data List.
   REAR RIGHT DOOR (REAR DOOR ECU RH)
   
   

   Tester Display	Measurement Item/Display	Normal Condition
   Lock Position SW	Rear RH side door lock position switch signal / ON or OFF	ON: Rear RH side door is unlocked OFF: Rear RH side door is locked

   OK

   On the screen, item changes between ON and OFF according to above chart.

NG → See step   12 

OK: Go to next step 

1. Using the Techstream, read the Data List.
   REAR RIGHT DOOR (REAR DOOR ECU RH)
   
   

   Tester Display	Measurement Item/Display	Normal Condition
   Outside Handle Trigger SW	Rear RH side door outside handle lock switch / ON or OFF	ON: Rear RH side door outside handle lock switch is pushed OFF: Rear RH side door outside handle lock switch is not pushed

   OK

   On the screen, item changes between ON and OFF according to above chart.

NG → See step   5 

OK: Go to next step 

1. Replace the rear door ECU RH with a new one or normally functioning one. Refer toCOMPONENTS .
2. Check that the entry function operates normally.

   OK

   Operates normally

NG → REPLACE CERTIFICATION ECU 

OK → END (REAR DOOR ECU RH IS DEFECTIVE) 

Fig 1: Inspect Rear Door Outside Handle RH

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Switch Condition	Specified Condition
   c1-3 (TRG+) - c1-1 (TRG-)	ON	Below 1 Ω
   c1-3 (TRG+) - c1-1 (TRG-)	OFF	10 kΩ or higher

NG → See step   11 

OK: Go to next step 

Fig 2: Identifying O3 ECU Connector Terminal And c1 Handle Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the c1 handle connector.
2. Disconnect the O3 ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Condition	Specified Condition
   c1-3 (TRG+) - O3-20 (TRG+)	Always	Below 1 Ω
   c1-3 (TRG+) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

Fig 3: Identifying c1 Handle Connector And c2 Oscillator Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the c1 handle connector.
2. Disconnect the c2 oscillator connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Condition	Specified Condition
   c1-1 (TRG-) - c2-9 (TRG-)	Always	Below 1 Ω
   c1-1 (TRG-) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Replace the door electrical key oscillator with a new one or normally functioning one. Refer toCOMPONENTS .
2. Check that the entry function operates normally.

   OK

   Operates normally

NG → See step   9 

OK → END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE) 

1. Replace the rear door ECU RH with a new one or normally functioning one. Refer toCOMPONENTS .
2. Check that the entry function operates normally.

   OK

   Operates normally

NG → REPLACE CERTIFICATION ECU 

OK → END (REAR DOOR ECU RH IS DEFECTIVE)