Rear Door LH Entry Unlock Function does not Operate: Procedure

1. When the master switch assembly's door control switch is operated, check that the locked doors unlock. Refer to OPERATION CHECK .

   OK

   Locked doors unlock.

NG → See step   10 

OK: Go to next step 

1. Using the Techstream, read the Data List. Refer to DATA LIST / ACTIVE TEST .
   REAR LEFT DOOR
   
   

   Tester Display	Measurement Item/Display	Normal Condition	Diagnostic Note
   Lock Position SW	Rear door LH lock position switch signal / ON or OFF	ON: Rear door LH is unlocked OFF: Rear door LH is locked	-

   OK

   On the Techstream screen, item changes between ON and OFF according to above chart.

NG → See step   12 

OK: Go to next step 

1. Using the Techstream, read the Data List. Refer to DATA LIST / ACTIVE TEST .
   REAR LEFT DOOR
   
   

   Tester Display	Measurement Item/Display	Normal Condition	Diagnostic Note
   Entry Sensor	Rear LH side door touch sensor / ON or OFF	ON: Rear LH side door sensor is touched OFF: Rear LH side door sensor is not touched	-

   OK

   On the Techstream screen, item changes between ON and OFF according to above chart.

NG → See step   5 

OK: Go to next step 

1. Replace the rear door ECU LH with a new one or normally functioning one. Refer to COMPONENTS .
2. Check that the entry function operates normally. Refer to OPERATION CHECK .

   OK

   Operates normally

NG → See step   11 

OK → END (REAR DOOR ECU LH IS DEFECTIVE) 

Fig 1: Identifying O14 ECU Connector And d2 Oscillator Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the O14 ECU connector.
2. Disconnect the d2 oscillator connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Condition	Specified Condition
   O14-16 (SEL) - d2-4 (SEL)	Always	Below 1 Ω
   O14-16 (SEL) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

Fig 2: Identifying D2 Oscillator Connector Terminal And D1 Handle Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disconnect the d2 oscillator connector.
2. Disconnect the d1 handle connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard resistance

   Tester Connection	Condition	Specified Condition
   d2-2 (SGT8) - d1-6 (SGT7)	Always	Below 1 Ω
   d2-2 (SGT8) - Body ground	Always	10 kΩ or higher

NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step 

1. Replace the door electrical key oscillator with a new one or normally functioning one. Refer to COMPONENTS .
2. Check that the entry function operates normally. Refer to OPERATION CHECK .

   OK

   Operates normally

NG → See step   8 

OK → END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE) 

1. Replace the rear door outside handle LH with a new one or normally functioning one. Refer to REMOVAL .
2. Check that the entry function operates normally. Refer to OPERATION CHECK .

   OK

   Operates normally

NG → See step   9 

OK → END (REAR DOOR OUTSIDE HANDLE LH IS DEFECTIVE) 

1. Replace the rear door ECU LH with a new one or normally functioning one. Refer to COMPONENTS .
2. Check that the entry function operates normally. Refer to OPERATION CHECK .

   OK

   Operates normally

NG → See step   11 

OK → END (REAR DOOR ECU LH IS DEFECTIVE)