Wireless Transmitter Memory Function does not Operate: Procedure

1. Use the Techstream to check if the CAN communication system is functioning normally. Refer to DIAGNOSIS SYSTEM [08/2012 - ] .

   OK

   CAN communication DTC is not output.

NG → See step   19 

OK: Go to next step 

1. Check the manual lock/unlock function by using the multiplex network master switch assembly. Refer to OPERATION CHECK [08/2012 - ] .

   OK

   Manual lock/unlock function operates normally.

NG → See step   16 

OK: Go to next step 

1. Check that the hybrid control system starts normally when the power switch is pressed with carrying the key and the brake pedal depressed. Refer to OPERATION CHECK [08/2012 - ] .

   OK

   Hybrid control system starts normally.

NG → See step   20 

OK: Go to next step 

1. Perform a seat position memory function. Refer to OPERATION CHECK [08/2012 - ] .
2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the seat position memory function.
   NOTE:

   • The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
   • If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

   OK

   Seat position memory function operates normally.

NG → See step   21 

OK: Go to next step 

1. Perform a seat position restoring function. Refer to OPERATION CHECK [08/2012 - ] .
2. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
   NOTE:

   • The seat position will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
   • If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

   OK

   Seat position restoring function operates normally.

NG → See step   15 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Data List.
5. Read the Data List according to the display on the Techstream.
   MAIN BODY (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
   
   

   Tester Connection	Measurement Item/Range	Normal Condition	Diagnostic Note
   FL Door Courtesy	Front door courtesy light switch assembly signal / ON or OFF	ON: Driver door open OFF: Driver door closed	-

   OK

   ON or OFF appears on the screen according to the driver door condition.

NG → See step   14 

OK: Go to next step 

1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.
   • Power switch is off
   • Press and hold the M1, M2 or M3 seat memory switch
   • Driver door closed
   • Carry the key
2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function. Refer to OPERATION CHECK [08/2012 - ] .

   OK

   Buzzer sounds normally.

NG → See step   10 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Main Body / Data List.
5. Read the Data List according to the display on the Techstream.
   MAIN BODY (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Mem SW No. w/KeyID1	Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3	NONE: No switches linked with key ID1 MEM SW1: M1 switch linked with key ID1 MEM SW2: M2 switch linked with key ID1 MEM SW3: M3 switch linked with key ID1	-
   Mem SW No. w/KeyID2	Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3	NONE: No switches linked with key ID2 MEM SW1: M1 switch linked with key ID2 MEM SW2: M2 switch linked with key ID2 MEM SW3: M3 switch linked with key ID2	-
   Mem SW No. w/KeyID3	Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3	NONE: No switches linked with key ID3 MEM SW1: M1 switch linked with key ID3 MEM SW2: M2 switch linked with key ID3 MEM SW3: M3 switch linked with key ID3	-
   Mem SW No. w/KeyID4	Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3	NONE: No switches linked with key ID4 MEM SW1: M1 switch linked with key ID4 MEM SW2: M2 switch linked with key ID4 MEM SW3: M3 switch linked with key ID4	-
   Mem SW No. w/KeyID5	Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3	NONE: No switches linked with key ID5 MEM SW1: M1 switch linked with key ID5 MEM SW2: M2 switch linked with key ID5 MEM SW3: M3 switch linked with key ID5	-
   Mem SW No. w/KeyID6	Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3	NONE: No switches linked with key ID6 MEM SW1: M1 switch linked with key ID6 MEM SW2: M2 switch linked with key ID6 MEM SW3: M3 switch linked with key ID6	-
   Mem SW No. w/KeyID7	Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3	NONE: No switches linked with key ID7 MEM SW1: M1 switch linked with key ID7 MEM SW2: M2 switch linked with key ID7 MEM SW3: M3 switch linked with key ID7	-

   OK

   On the Techstream display, it is confirmed that the memory call has been registered.

NG → See step   17 

OK: Go to next step 

1. Turn the power switch off.
2. Close and lock all doors.
3. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle with holding the memory call registered key.
4. Open the driver door and check that the driver seat moves to the memorized position. Refer to OPERATION CHECK [08/2012 - ] .

   OK

   Driver seat moves to the memorized position.

NG → See step   18 

OK → See step   22 

1. Replace the main body ECU (multiplex network body ECU). Refer to REMOVAL [08/2012 - ] .

NEXT: Go to next step 

1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.
   • Power switch is off
   • Press and hold the M1, M2 or M3 seat memory switch
   • Driver door closed
   • Carry the key
2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function. Refer to OPERATION CHECK [08/2012 - ] .

   OK

   Buzzer sounds normally.

NG → See step   12 

OK → END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) 

1. Replace the position control ECU and switch assembly. Refer to REMOVAL [08/2012 - ] .

NEXT: Go to next step 

1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.
   • Power switch is off
   • Press and hold the M1, M2 or M3 seat memory switch
   • Driver door closed
   • Carry the key
2. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function. Refer to OPERATION CHECK [08/2012 - ] .

   OK

   Buzzer sounds normally.

NG → See step   23 

OK → END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)