April 5, 2026: LEMON Manuals is launched! Read the announcement.

Freeze Frame Data [03/2012 - ]

FREEZE FRAME DATA
1. Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.

CHECK FREEZE FRAME DATA

Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the blind spot monitor main switch (warning canceling switch assembly) on.
Turn the Techstream on.
Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Trouble codes.

According to the display on the Techstream, display the Freeze Frame Data for the selected DTC.

BLIND SPOT MONITOR MASTER

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Main Switch	Blind spot monitor main switch (warning canceling switch assembly) / OFF or ON	ON: Blind spot monitor main switch (warning canceling switch assembly) ON OFF: Blind spot monitor main switch (warning canceling switch assembly) OFF	-
Master Side Turn Signal	State of the master side turn signal / OFF or ON	ON: Left turn signal received OFF: Left turn signal not received	-
Slave Side Turn Signal	State of the slave side turn signal / OFF or ON	ON: Right turn signal received OFF: Right turn signal not received	-
Warning Indicator Turning on (Master)	State of the outer rear view mirror indicator LH turning on / OFF or ON	OFF: The following conditions are not met ON: All of the following conditions are met Not during initial check Vehicle detected in left hand side warning area Left turn signal: OFF Vehicle speed 16 km/h (10 mph) or more Shift lever in any position except R Blind spot monitor warning light not illuminated	-
Warning Indicator Flashing (Master)	State of the outer rear view mirror indicator LH flashing / OFF or ON	OFF: The following conditions are not met ON: All of the following conditions are met Not during initial check Vehicle detected in left hand side warning area Left turn signal: ON Vehicle speed 16 km/h (10 mph) or more Shift lever in any position except R Blind spot monitor warning light not illuminated	-
Warning Indicator Input Circuit Voltage	The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V	Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V
Warning Indicator Input Circuit Current	The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA	Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA
Reverse	State of the shift position R signal / OFF or ON	ON: Shift lever in R OFF: Shift lever in any position except R	-
Vehicle Speed	Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)	Vehicle stopped: 0 km/h (0 mph)	-
Steering Angle	Steering angle sensor / Min.: -3072°, Max.: 3070.5°	Left turn: Increases Right turn: Decreases	-
Power Supply Voltage	Power supply voltage / Min.: 0 V, Max.: 50 V	Always: 11 to 14 V	-
Indicator Light Control State	Outer rear view mirror indicator dimming state / Dim OFF, Dim ON	Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed
Angle Adjustment by Auto alignment	Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg	Angle adjusted using auto alignment is displayed	When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Number of DTC	Number of DTC / Min.: 0, Max.: 255	When system is normal: 0 when a malfunction is detected: More than 0	-

BLIND SPOT MONITOR SLAVE

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Master Side Turn Signal	State of the master side turn signal / OFF or ON	ON: Left turn signal received OFF: Left turn signal not received	-
Slave Side Turn Signal	State of the slave side turn signal / OFF or ON	ON: Right turn signal received OFF: Right turn signal not received	-
Warning Indicator Turning on (Slave)	State of the outer rear view mirror indicator RH turning on / OFF or ON	OFF: The following conditions are not met ON: All of the following conditions are met Not during initial check Vehicle detected in right hand side warning area Right turn signal: OFF Vehicle speed 16 km/h (10 mph) or more Shift lever in any position except R Blind spot monitor warning light not illuminated	-
Warning Indicator Flashing (Slave)	State of the outer rear view mirror indicator RH flashing / OFF or ON	OFF: The following conditions are not met ON: All of the following conditions are met Not during initial check Vehicle detected in right hand side warning area Vehicle speed 16 km/h (10 mph) or more Right turn signal: ON Shift lever in any position except R Blind spot monitor warning light not illuminated	-
Warning Indicator Input Circuit Voltage	The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V	Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V
Warning Indicator Input Circuit Current	The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA	Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA
Reverse	State of the shift position R signal / OFF or ON	ON: Shift lever in R OFF: Shift lever in any position except R	-
Vehicle Speed	Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)	Vehicle stopped: 0 km/h (0 mph)	-
Steering Angle	Steering angle sensor / Min.: -3072°, Max.: 3070.5°	Left turn: Increases Right turn: Decreases	-
Power Supply Voltage	Power supply voltage / Min.: 0 V, Max.: 50 V	Always: 11 to 14 V	-
Indicator Light Control State	Outer rear view mirror indicator dimming state / Dim OFF, Dim ON	Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed
Angle Adjustment by Auto alignment	Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg	Angle adjusted using auto alignment is displayed	When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
Number of DTC	Number of DTC / Min.: 0, Max.: 255	When system is normal: 0 when a malfunction is detected: More than 0	-

CLEAR FREEZE FRAME DATA
NOTE:
Clearing the DTCs will also clear the Freeze Frame Data
1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.
4. Turn the Techstream on.
5. Clear the DTCs and Freeze Frame Data.