LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2015 >> CT 200h Base >> Repair and Diagnosis (Single Page) >> Restraints >> Air Bag, SRS >> Occupant Classification System - Diagnostic Codes & Symptom Tests >> Occupant Classification System >> DTC B1771: Passenger Side Buckle Switch Circuit Malfunction [08/2014 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC B1771: Passenger Side Buckle Switch Circuit Malfunction [08/2014 - ]: Procedure

  1. CHECK CONNECTORS 
    1. Turn the power switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
    3. Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt assembly RH.

      OK

      The connectors are properly connected.

      HINT: 

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.
    5. Check that the terminals of the connectors are not damaged.

      OK

      The terminals are not deformed or damaged.

    Result:  NG

    NG 

    REPLACE FRONT SEAT WIRE RH 

    Result:  OK

    OK 

    Refer to  2

  2. CHECK FRONT SEAT WIRE RH (SHORT TO B+) 
    1. Connect the cable to the negative (-) auxiliary battery terminal.
      GTY533443Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the power switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      W4-9 (BSW) - Body ground Power switch on (IG) Below 1 V
      W4-5 (BGND) - Body ground Power switch on (IG) Below 1 V
      TEXT IN ILLUSTRATION

      *1 Front Seat Inner Belt Assembly RH
      *2 Occupant Detection ECU
      *3 Front Seat Wire RH
      *4 Connector B
      *a Front view of wire harness connector
      (to Occupant Detection ECU)

    Result:  NG

    NG 

    REPLACE FRONT SEAT WIRE RH 

    Result:  OK

    OK 

    Refer to  3

  3. CHECK FRONT SEAT WIRE RH (OPEN) 
    1. Turn the power switch off.
      GTY524156Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
    3. Using SST, connect terminals 1 (BSW) and 2 (BGND) of connector C.
      NOTE:

      Do not forcibly insert SST into the terminals of the connector when connecting.

      • SST: 09843-18040 
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      W4-9 (BSW) - W4-5 (BGND) Always Below 1 Ω
      TEXT IN ILLUSTRATION

      *1 Front Seat Inner Belt Assembly RH *2 Occupant Detection ECU
      *3 Front Seat Wire RH *4 Connector B
      *5 Connector C - -
      *a Front view of wire harness connector
      (to Occupant Detection ECU)      		 *b Front view of wire harness connector
      (to Front Seat Inner Belt Assembly RH)

    Result:  NG

    NG 

    REPLACE FRONT SEAT WIRE RH 

    Result:  OK

    OK 

    Refer to  4

  4. CHECK FRONT SEAT WIRE RH (SHORT) 
    1. Disconnect SST from connector C.
      GTY533443Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      W4-9 (BSW) - W4-5 (BGND) Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Seat Inner Belt Assembly RH
      *2 Occupant Detection ECU
      *3 Front Seat Wire RH
      *4 Connector B
      *a Front view of wire harness connector
      (to Occupant Detection ECU)

    Result:  NG

    NG 

    REPLACE FRONT SEAT WIRE RH 

    Result:  OK

    OK 

    Refer to  5

  5. CHECK FRONT SEAT WIRE RH (SHORT TO GROUND) 
    1. Measure the resistance according to the value(s) in the table below.
      GTY533443Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard Resistance

      Tester Connection Condition Specified Condition
      W4-9 (BSW) - Body ground Always 1 MΩ or higher
      W4-5 (BGND) - Body ground Always 1 MΩ or higher
      TEXT IN ILLUSTRATION

      *1 Front Seat Inner Belt Assembly RH
      *2 Occupant Detection ECU
      *3 Front Seat Wire RH
      *4 Connector B
      *a Front view of wire harness connector
      (to Occupant Detection ECU)

    Result:  NG

    NG 

    REPLACE FRONT SEAT WIRE RH 

    Result:  OK

    OK 

    Refer to  6

  6. CHECK DTC 
    1. Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.
    2. Connect the cable to the negative (-) auxiliary battery terminal.
    3. Turn the power switch on (IG).
    4. Clear the DTCs stored in the occupant detection ECU (Refer to DTC Check / Clear [08/2014 - ] ).
    5. Clear the DTCs stored in the airbag sensor assembly (Refer to DTC Check / Clear [08/2014 - ] ).
    6. Turn the power switch off.
    7. Turn the power switch on (IG).
    8. Check for DTCs (Refer to DTC Check / Clear [08/2014 - ] ).

      OK

      DTC B1771 is not output.

      HINT: 

      Codes other than DTC B1771 may be output at this time, but they are not related to this check.

    Result:  OK

    OK 

    USE SIMULATION METHOD TO CHECK 

    (Refer to How To Proceed With Troubleshooting [08/2014 - ] )

    Result:  NG

    NG 

    Refer to  7

  7. CHECK FRONT SEAT INNER BELT ASSEMBLY RH 
    1. Turn the power switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
    3. Replace the front seat inner belt assembly RH with a known good one (Refer to Removal [08/2014 - ] for Manual seat. Refer to Removal [08/2014 - ] for Power seat).

      HINT: 

      Perform the following inspection using known good parts from another vehicle if possible.

    4. Connect the cable to the negative (-) auxiliary battery terminal.
    5. Turn the power switch on (IG).
    6. Clear the DTCs stored in the occupant detection ECU (Refer to DTC Check / Clear [08/2014 - ] ).
    7. Clear the DTCs stored in the airbag sensor assembly (Refer to DTC Check / Clear [08/2014 - ] ).
    8. Turn the power switch off.
    9. Turn the power switch on (IG).
    10. Check for DTCs (Refer to DTC Check / Clear [08/2014 - ] ).

      OK

      DTC B1771 is not output.

      HINT: 

      Codes other than DTC B1771 may be output at this time, but they are not related to this check.

    Result:  OK

    OK 

    END 

    Result:  NG

    NG 

    Refer to  8

  8. REPLACE OCCUPANT DETECTION ECU 
    1. Turn the power switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal.
    3. Replace the occupant detection ECU (Refer to Removal [08/2014 - ] ).

    Result:  NEXT

    NEXT 

    Refer to  9

  9. PERFORM ZERO POINT CALIBRATION 
    1. Connect the cable to the negative (-) auxiliary battery terminal.
    2. Turn the power switch on (IG).
    3. Using the Techstream, perform Zero Point Calibration (Refer to Initialization [08/2014 - ] ).

    Result:  NEXT

    NEXT 

    Refer to  10

  10. PERFORM SENSITIVITY CHECK 
    1. Using the Techstream, perform Sensitivity Check (Refer to Initialization [08/2014 - ] ).

    Result:  NEXT

    NEXT 

    END 

scientia non olet · About LEMON Manuals