DTC C2111/11: Transmitter ID1 Operation Stop; DTC C2112/12: Transmitter ID2 Operation Stop; DTC C2113/13: Transmitter ID3 Operation Stop; DTC C2114/14: Transmitter ID4 Operation Stop; DTC C2115/15: Transmitter ID5 Operation Stop [08/2013 - ]: Procedure

1. Set the tire pressure to the specified value. Refer to INSPECTION [08/2013 - ] .
2. Connect the Techstream to the DLC3.
3. Turn the engine switch on (IG).
4. Turn the Techstream on.
5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
6. Check the values by referring to the table below.
   TIRE PRESSURE MONITOR
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   ID1 Tire Inflation Pressure	ID1 tire inflation pressure / min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi), Relative pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi) max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2 , 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*
   ID2 Tire Inflation Pressure	ID2 tire inflation pressure / min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi), Relative pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi) max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2 , 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*
   ID3 Tire Inflation Pressure	ID3 tire inflation pressure / min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi), Relative pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi) max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2 , 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*
   ID4 Tire Inflation Pressure	ID4 tire inflation pressure / min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi), Relative pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi) max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2 , 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*
   ID5 Tire Inflation Pressure	ID5 tire inflation pressure / min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi), Relative pressure 0.0 kPa (0.0 kgf/cm2 , 0.0 psi) max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2 , 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2 , 78 psi)	Actual tire inflation pressure	If N/A is displayed, data has not been received.*

   HINT: 

   *: It may take approximately 2 or 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25. Refer to DTC C2121/21: No Signal from Transmitter ID1 in Main Mode; DTC C2122/22: No Signal from Transmitter ID2 in Main Mode; DTC C2123/23: No Signal from Transmitter ID3 in Main Mode; DTC C2124/24: No Signal from Transmitter ID4 in Main Mode; DTC C2125/25: No Signal from Transmitter ID5 in Main Mode; DTC C2181/81: Transmitter ID1 not Received (Test Mode DTC); DTC C2182/82: Transmitter ID2 not Received (Test Mode DTC); DTC C2183/83: Transmitter ID3 not Received (Test Mode DTC); DTC C2184/84: Transmitter ID4 not Received (Test Mode DTC); DTC C2185/85: Transmitter ID5 not Received (Test Mode DTC) [08/2013 - ] .

7. Rapidly reduce the tire pressure of each tire by at least 40 kPa (0.4 kgf/cm² , 5.8 psi) within 30 seconds.
   1. Check that tire pressure data for each tire displayed on the Techstream screen has changed.

      OK

      Tire pressure data for each tire displayed on the Techstream changes to the value of the tire pressure.

      NOTE:

      • It takes approximately 2 or 3 minutes to display the updated tire pressure data.
      • When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.
   2. After confirming that all of the tire pressure data displayed on the Techstream screen has changed, set the tire pressure of all tires to the specified values.

      HINT: 

      If the tire pressure data displayed on the Techstream has not changed after rechecking it, inspect for other problems (malfunction in transmission or reception function). Refer to DTC C2121/21: No Signal from Transmitter ID1 in Main Mode; DTC C2122/22: No Signal from Transmitter ID2 in Main Mode; DTC C2123/23: No Signal from Transmitter ID3 in Main Mode; DTC C2124/24: No Signal from Transmitter ID4 in Main Mode; DTC C2125/25: No Signal from Transmitter ID5 in Main Mode; DTC C2181/81: Transmitter ID1 not Received (Test Mode DTC); DTC C2182/82: Transmitter ID2 not Received (Test Mode DTC); DTC C2183/83: Transmitter ID3 not Received (Test Mode DTC); DTC C2184/84: Transmitter ID4 not Received (Test Mode DTC); DTC C2185/85: Transmitter ID5 not Received (Test Mode DTC) [08/2013 - ] .

NG → See step   2 

OK → END