Freeze Frame Data [04/2013 - ]
- FREEZE FRAME DATA NOTE:
- Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
- Turn the engine switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the Techstream.
- Turn the engine switch off.
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Check the freeze frame data.
- Enter the following menus: Body Electrical / Tilt & Telescopic / Trouble Codes.
Body Electrical > Tilt&Telescopic > Trouble Codes
Body Electrical > Tilt&Telescopic
Tester Display Measurement Item Range Normal Condition Diagnostic Note Tilt Position Current tilt position data Min.: 0
Max.: 6553528672 to 36864 - Telesco Position Current telescopic position data Min.: 0
Max.: 6553528672 to 36864 - Tilt Return Position Memorized tilt return position data Min.: 0
Max.: 6553528672 to 36864 - Telesco Return Position Memorized telescopic return position data Min.: 0
Max.: 6553528672 to 36864 - Tilt Up Switch Input state of tilt up switch ON or OFF ON: Tilt up switch activated
OFF: Tilt up switch not activated- Tilt Up SW(CAN) Input state of tilt up by switch ON or OFF - This item is not related to this vehicle Tilt Down Switch Input state of tilt down switch ON or OFF ON: Tilt down switch activated
OFF: Tilt down switch not activated- Tilt Down SW(CAN) Input state of tilt down switch ON or OFF - This item is not related to this vehicle Telesco Short Switch Input state of telescopic contract switch ON or OFF ON: Telescopic contract switch activated
OFF: Telescopic contract switch not activated- Telesco Short SW(CAN) Input state of telescopic contract switch ON or OFF - This item is not related to this vehicle Telesco Long Switch Input state of telescopic extend switch ON or OFF ON: Telescopic extend switch activated
OFF: Telescopic extend switch not activated- Telesco Long SW(CAN) Input state of telescopic extend switch ON or OFF - This item is not related to this vehicle T&T Manual SW Data Voltage data of tilt and telescopic switch Min.: 0.00 V
Max.: 4.99 VNeutral position: Below 0.20 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V- Power Source Voltage Voltage data of power supply Min.: 0.00 V
Max.: 19.99 V11.00 to 14.00 V - Freeze Speed Info Vehicle speed data Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)Actual vehicle speed - IG Switch (CAN) Communication state of engine switch ON or OFF ON: Communication normal
OFF: Communication interrupted- IG Switch Input state of engine switch ON or OFF ON: Input signal normal
OFF: Input signal interrupted- Receive from Meter Communication state of combination meter assembly signal OK or Interpt OK: Communication normal
Interpt: Communication interrupted- Receive from Seat ECU Communication state of front power seat switch LH signal OK or Interpt OK: Communication normal
Interpt: Communication interrupted- Receive from Combi Communication state of combination switch ECU signal OK or Interpt OK: Communication normal
Interpt: Communication interruptedThis item is not related to this vehicle J/B Communication state of main body ECU (multiplex network body ECU) signal OK or Interpt OK: Communication normal
Interpt: Communication interrupted- Handle Position Steering wheel position signal Away or Return Away: Steering wheel in away position
Return: Steering wheel in return position- The Number of DTCs Number of stored DTCs Min.: 0
Max.: 255Actual number of stored DTCs -