DTC B1787: Rear Occupant Classification Sensor LH Collision Detection [09/2014 - ]: Procedure

1. Turn the power switch on (IG), and wait for at least 60 seconds.
2. Clear the DTCs (Refer to DTC CHECK / CLEAR [09/2014 - ] ).
3. Turn the power switch off.
4. Turn the power switch on (IG), and wait for at least 60 seconds.
5. Check for DTCs (Refer to DTC CHECK / CLEAR [09/2014 - ] ).

   OK

   DTC B1787 is not output.

   HINT: 

   DTCs other than DTC B1787 may be output at this time, but they are not related to this check.

Result:  OK

OK 

USE SIMULATION METHOD TO CHECK 

(Refer to DIAGNOSIS SYSTEM [09/2014 - ] )

Result:  NG

NG 

See step  2

1. Perform the zero point calibration (Refer to INITIALIZATION [09/2014 - ] ).

   OK

   "Zero Point Calibration is complete." is displayed.

Result:  NG

NG 

See step  5

Result:  OK

OK 

See step  3

1. Perform the sensitivity check (Refer to INITIALIZATION [09/2014 - ] ).

   Standard

   27 to 33 kg (59.5 to 72.8 lb)

Result:  NG

NG 

See step  5

Result:  OK

OK 

See step  4

1. Clear the DTCs (Refer to DTC CHECK / CLEAR [09/2014 - ] ).
2. Turn the power switch off.
3. Turn the power switch on (IG), and wait for at least 60 seconds.
4. Check for DTCs (Refer to DTC CHECK / CLEAR [09/2014 - ] ).

   OK

   DTC B1787 is not output.

   HINT: 

   DTCs other than DTC B1787 may be output at this time, but they are not related to this check.

Result:  OK

OK 

END 

Result:  NG

NG 

See step  5

1. Turn the power switch off.
2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
3. Replace the front seat adjuster assembly RH.
   • for Sports Seat Type (Refer to REMOVAL [09/2014 - ] )
   • for Standard Seat Type (Refer to REMOVAL [09/2014 - ] )
   • for Luxury Seat Type (Refer to REMOVAL [09/2014 - ] )

   HINT: 

   Perform the inspection using parts from a normal vehicle when possible.

Result:  NEXT

NEXT 

See step  6

1. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
2. Turn the power switch on (IG).
3. Perform the zero point calibration (Refer to INITIALIZATION [09/2014 - ] ).

   OK

   "Zero Point Calibration is complete." is displayed.

Result:  NG

NG 

See step  9

Result:  OK

OK 

See step  7

1. Perform the sensitivity check (Refer to INITIALIZATION [09/2014 - ] ).

   Standard

   27 to 33 kg (59.5 to 72.8 lb)

Result:  NG

NG 

See step  9

Result:  OK

OK 

See step  8

1. Clear the DTCs (Refer to DTC CHECK / CLEAR [09/2014 - ] ).

   HINT: 

   • First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the center airbag sensor.
   • Use the Techstream to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
2. Turn the power switch off.
3. Turn the power switch on (IG), and wait for at least 60 seconds.
4. Check for DTCs (Refer to DTC CHECK / CLEAR [09/2014 - ] ).

   OK

   DTC B1787 is not output.

   HINT: 

   DTCs other than DTC B1787 may be output at this time, but they are not related to this check.

Result:  OK

OK 

END (FRONT SEAT ADJUSTER ASSEMBLY RH [REAR OCCUPANT CLASSIFICATION SENSOR LH] WAS DEFECTIVE) 

Result:  NG

NG 

See step  9

1. Turn the power switch off.
2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.
3. Replace the occupant detection ECU (Refer to REMOVAL [09/2014 - ] ).

   HINT: 

   Perform the inspection using parts from a normal vehicle when possible.

Result:  NEXT

NEXT 

See step  10

1. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
2. Turn the power switch on (IG).
3. Perform the zero point calibration (Refer to DIAGNOSIS SYSTEM [09/2014 - ] ).

   OK

   "Zero Point Calibration is complete." is displayed.

Result:  NEXT

NEXT 

See step  11

1. Perform the sensitivity check (Refer to INITIALIZATION [09/2014 - ] ).

   Standard

   27 to 33 kg (59.5 to 72.8 lb)

Result:  NEXT

NEXT 

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)