System Description [09/2014 - ]

SYSTEM FUNCTION

Function	Outline
Push-button start function	When the key is brought into the vehicle and verified, this function changes the power source or starts the hybrid control system when the power switch and brake pedal are operated.
saving function for vehicle	When the vehicle is not used for a long time, this function extends the interval between each periodic transmission of the request signal, or stops transmission of the request signal to save auxiliary battery power. When 5 days elapse without a response from the key, periodic transmission stops. When 14 days elapse without a response from the key, the lock/unlock sensor of all door outside handle assemblies except the driver door is disabled. When the electrical key transmitter sub-assembly is left in a detection area for 10 minutes or more, the smart access system with push-button start automatically deactivates the exterior detection area the key is in.
Transmitter battery saving function	Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode. Check that the smart access system with push-button start does not operate while in transmitter battery saving mode. To cancel transmitter battery saving mode, press a button of the electrical key transmitter sub-assembly.
Battery saving function for key	If a switch on the key is depressed and held, this function stops transmission of the signal after approximately 20 seconds to save key battery power.
Key cancel function	Cancels the smart access system with push-button start when certain operations are performed.
Immobilizer function	Allows the hybrid control system to be started only using registered keys to prevent an unauthorized hybrid control system start.
Automatic power off function	When the shift lever is in P and the power source mode is on (ACC) (the hybrid control system has not been started and the vehicle is not moving), this function automatically turns off the power after approximately 20 minutes elapse. When the shift lever is in P and the power source mode is on (IG) (the hybrid control system has not been started and the vehicle is not moving), this function automatically turns off the power after approximately 60 minutes elapse.
Remote engine start and stop function*	Sends remote engine start and stop operation signals requested by the user using an electrical key transmitter sub-assembly or application to the certification ECU (smart key ECU assembly) (Refer to SYSTEM DESCRIPTION [09/2014 - 10/2015] or SYSTEM DESCRIPTION [10/2015 - ] ).

*: w/ Lexus Enform Remote

REMOTE ENGINE START AND STOP FUNCTION (w/ Lexus Enform Remote)
1. Remote engine start and stop function (start operation)
  1. When using the electrical key transmitter sub-assembly:
    1. Point the electrical key transmitter sub-assembly at the vehicle and press and release the lock switch twice. Immediately press and hold the lock switch.
    HINT:
    
    The hybrid control system can be started by the remote engine start and stop function when all of the following conditions are met:
    - All of the doors are closed.
    - The engine hood is closed.
    - The power switch is off.
    - The auxiliary battery voltage is 11 V or higher.
    - The cumulative hybrid control system operating time after being started by remote engine start and stop is less than 15 minutes.
    - All of the doors are locked by electrical key transmitter sub-assembly.
    - The hybrid control system has not already been started by remote engine start and stop.
  2. When using the application:
    Refer to OPERATION CHECK [09/2014 - 10/2015] or OPERATION CHECK [10/2015 - ] .
2. Remote engine start and stop function (stop operation)
  1. When using the electrical key transmitter sub-assembly, perform either of the following operations:
    1. Press the unlock switch.
    2. Press and hold the lock switch.
    HINT:
    
    The hybrid control system will stop when any of the following conditions is met:
    - Any door is opened.
    - The engine hood is opened.
    - The power switch is pressed.
    - A stop request is received from the electrical key transmitter sub-assembly.
    - The theft deterrent system enters the alarm sounding state.
    - The auxiliary battery voltage drops to less than 11 V.
    - 10 minutes elapse after the hybrid control system turn on (READY).
    - The cumulative hybrid control system operating time after being started by remote engine start and stop is 20 minutes or more.
    - The shift lever is moved to a position other than P.
    - The vehicle speed is 5 km/h or more.
    - The stop lights illuminate or its condition cannot be determined.
    - Any door is unlocked.
    - The engine speed is more than 3000 rpm for 0.2 seconds.
    - The hybrid control system stops for 3 seconds.
    - The hybrid control system is malfunctioning.
    - The fuel level warning is displayed on the multi-information display in the combination meter assembly.
    - The CAN communication is malfunctioning.
  2. When using the application:
    Refer to OPERATION CHECK [09/2014 - 10/2015] or OPERATION CHECK [10/2015 - ] .
3. Remote air conditioner system
  Refer to CUSTOMIZE PARAMETERS [09/2014 - ] .
DETECTION AREA
NOTE:
- Depending on the vehicle body shape, the key may not operate in certain locations.
- Even if the key is in the vehicle exterior key detection area, the key may not be properly detected if the key is near a window, a door handle or the center of the rear bumper.
- Even if the key is in the vehicle interior key detection area, the key may not be properly detected if the key is on the instrument panel, in the glove box or on the floor.
- Depending on the way the key is held, the key may not operate properly.
- The key detection area may reduce in size or the key may not be properly detected under the conditions below:
  - The key battery is depleted.
  - There are TV towers, electric power plants, broadcasting stations, gas stations or other facilities that produce strong electric waves nearby.
  - Wireless products such as cell phones, etc. are carried with the key.
  - The key is covered by or in contact with a metal object.
  - Electric wave-type keyless entry systems are being operated nearby.
  - The key is placed near high-voltage equipment or equipment that emits electrical noise.
1. The request signal sent from the certification ECU (smart key ECU assembly) is transmitted from each electrical key antenna (outside) to form the smart key detection area. The detection area formed by each electrical key antenna (outside) has a detection range of 0.7 to 1 m (2.30 to 3.28 ft.) from the door handles and rear bumper (electrical key antenna [outside luggage]).
2. When the vehicle is parked (the power source mode is off and the doors are locked*), the detection area of each electrical key antenna (outside) is formed by emitting a periodic request signal every 0.25 seconds in order to detect the key. Also, when the doors are locked and a lock sensor is touched, a request signal is emitted, the detection area outside the vehicle is formed and the key is detected.
  HINT:
  
  *: The smart access system with push-button start controls each door individually. After a door is locked with the door lock switch or wireless remote control function, a detection area is formed at the locked door even if all the doors are not locked.
3. The detection area of the electrical key antenna (outside luggage) is formed when the luggage door opening switch assembly is pressed.
4. The detection area inside the vehicle is formed and the key is detected when any of the following conditions are met: 1) The driver door is opened and closed, 2) the brake pedal is depressed, 3) the power switch is operated, 4) the conditions required for various warnings are met, or 5) a smart door lock operation is performed.
5. The detection area inside the vehicle when starting the hybrid control system can be customized through the customize function.