Operation Check [10/2014 - 09/2017]

1. Turn the engine switch on (ACC).
2. With the mirror select switch set to L, check that the mirror surface moves up, down, left and right normally.
3. With the mirror select switch set to R, check that the mirror surface moves up, down, left and right normally.

Fig 1: Identifying Memory Switches

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

If the M1 switch, M2 switch and M3 switch are simultaneously pressed while the SET switch is pressed and held, the seat position will not be stored.

1. Turn the engine switch on (IG) and move the shift lever to P.
2. Check the M1 switch.
   1. Using the outer mirror switch assembly, turn the mirror surface to the full left position.
      Fig 2: Turning Mirrors Full Left

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *a	Turn to Left Fully

   2. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized when the M1 switch is pressed within 3 seconds after the SET switch is pressed.
      NOTE:

      • The mirror surface position will also be stored when the M1 switch is pressed after first pressing and holding the SET switch.
      • The mirror surface position will not be stored when the SET switch and M1 switch are pressed simultaneously.
      • The mirror surface position will not be stored when 2 or more of the seat memory switches are pressed simultaneously (for example, M1 and M2) after first pressing the SET switch.
   3. Using the outer mirror switch assembly, turn the mirror surface to the full right position.
   4. Press the M1 switch.
   5. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized full left position.
3. Check the M2 switch.
   1. Using the outer mirror switch assembly, turn the mirror surface to the full right position.
      Fig 3: Turning Mirrors Full Right

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *a	Turn to Right Fully

   2. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized when the M2 switch is pressed within 3 seconds after the SET switch is pressed.
      NOTE:

      • The mirror surface position will also be stored when the M2 switch is pressed after first pressing and holding the SET switch.
      • The mirror surface position will not be stored when the SET switch and M2 switch are pressed simultaneously.
      • The mirror surface position will not be stored when 2 or more of the seat memory switches are pressed simultaneously (for example, M1 and M2) after first pressing the SET switch.
   3. Using the outer mirror switch assembly, turn the mirror surface to the full left position.
   4. Press the M2 switch.
   5. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized full right position.
4. Check the M3 switch.
   1. Using the outer mirror switch assembly, turn the mirror surface to the full left position.
      Fig 4: Turning Mirrors Full Left

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *a	Turn to Left Fully

   2. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized when the M3 switch is pressed within 3 seconds after the SET switch is pressed.
      NOTE:

      • The mirror surface position will also be stored when the M3 switch is pressed after first pressing and holding the SET switch.
      • The mirror surface position will not be stored when the SET switch and M3 switch are pressed simultaneously.
      • The mirror surface position will not be stored when 2 or more of the seat memory switches are pressed simultaneously (for example, M2 and M3) after first pressing the SET switch.
   3. Using the outer mirror switch assembly, turn the mirror surface to the full right position.
   4. Press the M3 switch.
   5. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized full left position.
5. Check that switches M1, M2 and M3 cause the outer mirror to move to the recorded outer mirror positions under the following conditions: the engine switch is turned off, the driver door is opened, and M1, M2 or M3 is pressed within 180 seconds.
6. Check that switches M1, M2 and M3 cause the outer mirror to move to the recorded outer mirror positions under the following conditions: the engine switch is turned off, the driver door is closed, and M1, M2 or M3 is pressed within 60 seconds.

1. Turn the engine switch on (IG).
2. Set the mirror select switch to L or R.
3. Check that the mirror surface turns downward when the shift lever is moved to R.
4. Check that the mirror surface position returns to the original position when one of the following conditions is met:
   • Shift lever is moved to any position other than R.
   • Mirror select switch is in the neutral position (off).
   • Engine switch is turned off.

1. Turn the engine switch on (IG).
2. Set the mirror select switch to L or R.
3. Check that the mirror surface turns downward when the shift lever is moved to R.
4. While the mirror is in the reverse shift-linked operation position, move the mirror to the desired position.
5. Check that the mirror moves to its normal position when the shift lever is moved to a different position from R, and then moves back to the memorized position when the shift lever is moved to R again.

1. Memory call function check.
   1. With a transmitter key recognition code registered:

      With the recognition code of the transmitter registered in memory, perform an entry unlock or wireless unlock operation. Open the driver door and check that the front seat, steering wheel (tilt & telescopic) and outer mirror surface position automatically move to the positions memorized in memory.

2. Memory registration.
   1. Prepare by memorizing the driving position through the seat memory switch (M1, M2 or M3).
   2. With the engine switch on (IG), press and hold both of the following: a seat memory switch (M1, M2 or M3) and door control switch (LOCK or UNLOCK). Continue holding the switches until the answer-back buzzer sounds once (0.5 seconds).
      NOTE:

      Do not bring 2 or more keys into the vehicle.

3. Memory erasure.
   1. With the engine switch on (IG), press and hold both of the following: the SET switch and door control switch (LOCK or UNLOCK). Continue holding the switches until the answer-back buzzer sounds twice (0.1 seconds each time).
      NOTE:

      Do not bring 2 or more keys into the vehicle.

1. While a memory call function is operating, check that any one of the following actions will stop the memory call operation: 1) pressing the SET, M1, M2 or M3 switch, 2) moving the shift lever to R, 3) moving the mirror surface manually, or 4) moving the mirror surface to the uppermost, lowermost, leftmost or rightmost position.

1. Turn the engine switch on (IG).
2. Check that pressing the rear window defogger switch (mirror heater switch) illuminates the indicator and warms the mirror surface.
3. Check that after approximately 15 minutes, the indicator light turns off and the mirror heater deactivates.

   HINT: 

   There is a timer extension function which can operate the mirror heater system for up to an additional 45 minutes.

1. Check that the automatic glare-resistant EC mirror function of the outer rear view mirror assembly operates when the automatic glare-resistant function of the inner rear view mirror assembly is operating.