LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2021 >> NX 300 Base, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Entertainment Systems >> Active Sound Control (ASC) System - Diagnostics - Introduction >> ASC System >> Data List / Active Test [10/2014 - 09/2017] >> Data List / Active Test [10/2014 - 09/2017]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test [10/2014 - 09/2017]

  1. DATA LIST 
    NOTE:

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / ASC / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > ASC > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Sound State Simulated engine sound output status Stopping or Sounding Stopping: Simulated engine sound stopped
      Sounding: Simulated engine sound being output      		 -
      Mute Mute setting OFF or ON OFF: Mute off
      ON: Mute on      		 -
      Gear Position (D Range) Gear position information 1st, 2nd, 3rd, 4th, 5th or 6th Actual gear position -
      Suppositional Engine Speed (Target Value) Calculated engine speed in the stereo component equalizer assembly Min.: 0 rpm
      Max.: 8000 rpm      		 Changes according to driving conditions (accelerator pedal opening angle, vehicle speed, etc.) -
      Volume SW Vehicle sound switch on/off status OFF or ON OFF: Vehicle sound switch off
      ON: Vehicle sound switch on      		 -
      Speaker Disconnection Inspection State of wire harness between stereo component equalizer assembly and No. 1 speaker assembly with box OFF or Inspecting OFF: Open not detected
      Inspecting: Open detected      		 -
      Volume Switch Voltage The VSLI terminal voltage to the CPU of the stereo compartment equalizer assembly Min.: 0 V
      Max.: 5 V      		 Changes according to vehicle sound switch volume setting -
      Accelerator Position Accelerator pedal opening angle Min.: 0%
      Max.: 111.0%      		 Actual accelerator pedal opening angle -
      Shift SW Status (P Range) Park/Neutral position switch status OFF or ON OFF: Shift lever in any position other than P
      ON: Shift lever in P      		 -
      Shift SW Status (R Range) Shift lever position (R) OFF or ON OFF: Shift lever in any position other than R
      ON: Shift lever in R      		 -
      Shift SW Status (D Range) Shift lever position (D) OFF or ON OFF: Shift lever in any position other than D
      ON: Shift lever in D      		 -
      Shift SW Status (N Range) Shift lever position (N) OFF or ON OFF: Shift lever in any position other than N
      ON: Shift lever in N      		 -
      Gear Position (Sports Mode) Gear position information with shift lever in S Not Sports Mode, 1st, 2nd, 3rd, 4th, 5th or 6th Not Sports Mode: Shift lever in any position other than S
      1st: S1 gear range selected
      2nd: S2 gear range selected
      3rd: S3 gear range selected
      4th: S4 gear range selected
      5th: S5 gear range selected
      6th: S6 gear range selected      		 -
      Current Gear Position (D Range) Current gear position information 1st, 2nd, 3rd, 4th, 5th or 6th Current gear position displayed (1st, 2nd, 3rd, 4th, 5th or 6th) -
      Integrated Sport Mode Indicator Drive mode (SPORT) status OFF or Lighting OFF: Drive mode other than SPORT mode selected
      Lighting: SPORT mode selected      		 -
      ECO Mode Indicator ECO mode indicator illumination status OFF or Lighting OFF: ECO mode indicator not illuminated
      Lighting: ECO mode indicator illuminates      		 -
      Integrated Sport Mode Status Drive mode (SPORT, SPORT S or SPORT S+) status Not Sport, PWR & Chassis, Chassis or PWR Not Sport: Drive mode other than SPORT, SPORT S or SPORT S+ mode selected
      PWR & Chassis: SPORT S+ mode selected
      Chassis: SPORT S mode selected
      PWR: SPORT S mode selected      		 -
      Engine Revolution Actual engine speed Min.: 0 rpm
      Max.: 10000 rpm      		 Actual engine speed -
      Gear Shifting Signal Shifting status OFF or ON OFF: Gear not being changed
      ON: Gear being changed      		 -
      Number of DTC Number of trouble codes Min.: 0
      Max.: 255      		 Number of DTCs displayed -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / ASC / Active Test.
    5. Perform the Active Test according to the display on the Techstream.

      Body Electrical > ASC > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Sound ASC system ON or OFF -
scientia non olet · About LEMON Manuals