LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2022 >> ES 250 Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Headlights >> Lighting System (Ext) (Except Hybrid) - Diagnostic Codes (2 Of 2) & Symptom Tests >> LIGHTING SYSTEM (for Gasoline Model) >> DTC U0073: Control Module Communication Bus OFF; DTC U0126: Lost Communication with Steering Angle Sensor Module; DTC U0142: Lost Communication with Body Control Module "B"; DTC U0182: Lost Communication With Lighting Control Module Front [06/2018 - ] >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC U0073: Control Module Communication Bus OFF; DTC U0126: Lost Communication with Steering Angle Sensor Module; DTC U0142: Lost Communication with Body Control Module "B"; DTC U0182: Lost Communication With Lighting Control Module Front [06/2018 - ]: Procedure

  1. CONFIRM MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      For LED Type Turn Signal Light A
      For Bulb Type Turn Signal Light B

    Result: 

    See step  4

    Result: 

    See step  2

  2. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / AFS (Sub) / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > AFS (Sub) > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  3

  3. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Wait 20 seconds or more.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / AFS (Sub) / Trouble Codes.
    6. Check for DTCs.

      Body Electrical > AFS (Sub) > Trouble Codes 

      OK

      DTCs are not output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

    Result: 

    NG 

    GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

  4. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / HL AutoLeveling (Sub) / Trouble Codes.
    5. Clear the DTCs.

      Body Electrical > HL AutoLeveling (Sub) > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Wait 35 seconds or more.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / HL AutoLeveling (Sub) / Trouble Codes.
    6. Check for DTCs.

      Body Electrical > HL AutoLeveling (Sub) > Trouble Codes 

      OK

      DTCs are not output.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

    Result: 

    NG 

    GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]