DTC U0073: Control Module Communication Bus Off; DTC U0100: Lost Communication With ECM/PCM "A"; DTC U0124: Lost Communication With Lateral Acceleration Sensor Module; DTC U0126: Lost Communication With Steering Angle Sensor Module; DTC U110F: Lost Communication With Roll Rate Sensor/Vertical Acceleration Sensor Module [11/2017 - 03/2019]: Procedure

1. Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

   Refer to CHECK FOR INTERMITTENT PROBLEMS [11/2017 - 03/2019]

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   EFI Communication Open	ECM communication open detection	Error or Normal	Error: Momentary interruption Normal: Normal	-
   Yaw Rate Open	Yaw rate sensor open detection	Error or Normal	Error: Momentary interruption Normal: Normal	-
   Deceleration Open	Acceleration sensor open detection	Error or Normal	Error: Momentary interruption Normal: Normal	-
   Steering Open	Steering angle sensor open detection	Error or Normal	Error: Momentary interruption Normal: Normal	-
   Vertical Acceleration Sensor Open	Momentary interruption (open circuit) status in the wire harness between the skid control ECU (brake actuator assembly) and the roll rate and vertical acceleration sensor (yaw rate sensor)	Error or Normal	Error: Momentary interruption Normal: Normal	-

   Chassis > ABS/VSC/TRAC > Data List 

   Tester Display
   EFI Communication Open
   Yaw Rate Open
   Deceleration Open
   Steering Open
   Vertical Acceleration Sensor Open

   Result

   Result	Proceed to
   There is a constant open circuit.	A
   There are no momentary interruptions.	B
   There are momentary interruptions.	C

   HINT: 

   Perform the above inspection before disconnecting any sensors or connectors.

Result: 

B 

See step  3

Result: 

C 

See step  4

Result: 

A 

See step  2

1. Turn the engine switch off.
2. Check if each sensor and ECM connector is securely connected.

   OK

   Each connector is securely connected.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY 

Result: 

OK 

See step  3

1. Turn the engine switch off.
2. Record the output DTCs (for VSC system and/or CAN communication system).

   for VSC system: Refer to DTC CHECK / CLEAR [11/2017 - 03/2019]

   for CAN communication system: Refer to DIAGNOSIS SYSTEM [11/2017 - 03/2019]

   Chassis > ABS/VSC/TRAC > Trouble Codes 

   HINT: 

   If CAN communication system DTCs and related sensor DTCs are output simultaneously, troubleshoot the DTCs (for VSC system) after the CAN communication system returns to normal.

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output (relating to VSC system).	B
   DTCs are output (relating to CAN communication system).	C

Result: 

A 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2017 - 03/2019] 

Result: 

B 

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2017 - 03/2019] 

Result: 

C 

INSPECT CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2017 - 03/2019] 

1. Turn the engine switch off.
2. Repair or replace the harness or connector.
3. Check for any momentary interruptions between the skid control ECU (brake actuator assembly) and each sensor or ECM.

   Refer to CHECK FOR INTERMITTENT PROBLEMS [11/2017 - 03/2019]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  5

1. Turn the engine switch off.
2. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [11/2017 - 03/2019]

   Chassis > ABS/VSC/TRAC > Clear DTCs 

3. Turn the engine switch off.
4. Start the engine.
5. Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.
6. Check that no CAN communication system DTCs are output.

   Refer to DIAGNOSIS SYSTEM [11/2017 - 03/2019]

7. If VSC system DTCs are output, record them.

   Refer to DTC CHECK / CLEAR [11/2017 - 03/2019]

   Chassis > ABS/VSC/TRAC > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output.	A
   DTCs are output (relating to VSC system).	B
   DTCs are output (relating to CAN communication system).	C

   HINT: 

   The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for VSC system).

Result: 

A 

END 

Result: 

B 

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2017 - 03/2019] 

Result: 

C 

INSPECT CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2017 - 03/2019]