Four-Wheel Drive (4WD) Systems - Vehicles With: Torque Vectoring DTCS: AWD
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| P0562:16 | System Voltage Low: Circuit Voltage Below Threshold | GO to Pinpoint Test G |
| P0563:17 | System Voltage High: Circuit Voltage Above Threshold | GO to Pinpoint Test H |
| P0748:11 | Pressure Control Solenoid "A" Electrical: Circuit Short To Ground | GO to Pinpoint Test I |
| P0748:12 | Pressure Control Solenoid "A" Electrical: Circuit Short To Battery | GO to Pinpoint Test I |
| P0748:13 | Pressure Control Solenoid "A" Electrical: Circuit Open | GO to Pinpoint Test I |
| P0778:11 | Pressure Control Solenoid "B" Electrical: Circuit Short To Ground | GO to Pinpoint Test I |
| P0778:12 | Pressure Control Solenoid "B" Electrical: Circuit Short To Battery | GO to Pinpoint Test I |
| P0778:13 | Pressure Control Solenoid "B" Electrical: Circuit Open | GO to Pinpoint Test I |
| P0C01:19 | Drive Motor "A" Current High: Circuit Current Above Threshold | GO to Pinpoint Test J |
| P0C05:13 | Drive Motor "A" Phase U-V-W Circuit/Open: Circuit Open | GO to Pinpoint Test J |
| P0C06:11 | Drive Motor "A" Phase U-V-W Circuit Low: Circuit Short To Ground | GO to Pinpoint Test J |
| P0C07:12 | Drive Motor "A" Phase U-V-W Circuit High: Circuit Short To Battery | GO to Pinpoint Test J |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | The module could not communicate on the network at a point in time. The fault is not currently present since the module had to communicate with the diagnostic scan tool to report this DTC. VERIFY the integrity of the connectors and wiring. DIAGNOSE no HS-CAN communication, all modules are not responding. REFER to: Communications Network . |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to Pinpoint Test C |
| U0129:87 | Lost Communication With Brake System Control Module "A": Missing Message | GO to Pinpoint Test D |
| U0131:87 | Lost Communication With Power Steering Control Module: Missing Message | GO to Pinpoint Test E |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test F |
| U0401:00 | Invalid Data Received From ECM / PCM "A": No Sub Type Information | RETRIEVE and REPAIR all non-network DTCs in the PCM. REFER to: Electronic Engine Controls . |
| U0418:00 | Invalid Data Received From Brake System Control Module "A": No Sub Type Information | RETRIEVE and REPAIR all non-network DTCs in the ABS. REFER to: ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL . |
| U0420:00 | Invalid Data Received From Power Steering Control Module: No Sub Type Information | RETRIEVE and REPAIR all non-network DTCs in the PSCM. REFER to: Power Steering . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and REPAIR all non-network DTCs in the BCM. REFER to: Body Control Module (BCM) . |
| U2008:16 | Sensor Cluster: Circuit Voltage Below Threshold | GO to Pinpoint Test K |
| U2008:17 | Sensor Cluster: Circuit Voltage Above Threshold | GO to Pinpoint Test K |
| U2008:64 | Sensor Cluster: Signal Plausibility Failure | GO to Pinpoint Test K |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new AWD module to correct the failure to retain configuration data. REFER to: Axle Assembly - 3.0L EcoBoost . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new AWD module to correct the failure to retain configuration data. REFER to: Axle Assembly . |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | Reprogram the AWD module to the latest calibration. If the module already has the latest calibration, CLEAR the DTCs. CYCLE the ignition. CARRY OUT the AWD module self-test. RETRIEVE and RECORD all DTCs. If the DTC returns INSTALL a new AWD module. REFER to: Axle Assembly . |
| U3000:47 | Control Module: Watchdog / Safety μCa Failure | CLEAR the DTCs. CYCLE the ignition. CARRY OUT the AWD module self-test. RETRIEVE and RECORD all DTCs. Road test the vehicle, If the DTC returns INSTALL a new AWD module. |
| U3000:4B | Control Module: Over Temperature | This DTC sets due to excessive temperatures in the AWD module. Allow the vehicle to cool down for at least 30 minutes. |
| U3000:92 | Control Module: Performance or Incorrect Operation | INSTALL a new rear drive unit (RDU). REFER to: Axle Assembly . |