LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lincoln >> 2018 >> Navigator Select, 4WD >> Repair and Diagnosis (Single Page) >> General Information >> DTC Index >> DTC Index (Glass, Frames And Mechanisms - Powertrain) >> Information System And Entertainment System DTCS >> Accessory Protocol Interface Module (APIM)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Accessory Protocol Interface Module (APIM)

DTC INDEX

DTC Description Action
B108E:01 Display: General Electrical Failure GO to Pinpoint Test L
B108E:02 Display: General Signal Failure GO to Pinpoint Test L
B108E:4A Display: Incorrect Component Installed INSTALL the correct FDIM as necessary. Refer to: Front Display Interface Module (FDIM) .
B108E:4B Display: Over Temperature GO to Pinpoint Test L
B108E:87 Display: Missing Message GO to Pinpoint Test L
B119F:01 GPS Antenna: General Electrical Failure GO to Pinpoint Test S
B119F:13 GPS Antenna: Circuit Open GO to Pinpoint Test S
B1252:11 USB Port: Circuit Short To Ground GO to Pinpoint Test P
B1252:13 USB Port: Circuit Open GO to Pinpoint Test P
B14FD:11 External Media Control Connectivity: Circuit Short To Ground GO to Pinpoint Test P
B1D79:11 Microphone Input: Circuit Short To Ground GO to Pinpoint Test O
B1D79:12 Microphone Input: Circuit Short To Battery GO to Pinpoint Test O
B1D79:13 Microphone Input: Circuit Open GO to Pinpoint Test O
C1001:01 Vision System Camera: General Electrical Failure REFER to: Parking Aid .
U0121:00 Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information GO to Pinpoint Test Z
U0140:00 Lost Communication With Body Control Module: No Sub Type Information GO to Pinpoint Test AA
U0151:00 Lost Communication With Restraints Control Module: No Sub Type Information GO to Pinpoint Test AC
U0155:00 Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information GO to Pinpoint Test AD
U0159:00 Lost Communication With Parking Assist Control Module "A": No Sub Type Information GO to Pinpoint Test AE
U0184:00 Lost Communication With Radio: No Sub Type Information GO to Pinpoint Test AG
U0196:00 Lost Communication With Entertainment Control Module-Rear "A": No Sub Type Information GO to Pinpoint Test AH
U0198:00 Lost Communication With Telematic Control Module: No Sub Type Information GO to Pinpoint Test AI
U0208:00 Lost Communication With "Seat Control Module A": No Sub Type Information GO to Pinpoint Test AJ
U020C:00 Lost Communication with Wireless Accessory Charging Module "A": No Sub Type Information GO to Pinpoint Test AK
U0232:00 Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information GO to Pinpoint Test AL
U0233:00 Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information GO to Pinpoint Test AM
U0238:00 Lost Communication With Digital Audio Control Module "D": No Sub Type Information GO to Pinpoint Test AO
U023B:00 Lost Communication With Image Processing Module B: No Sub Type Information GO to Pinpoint Test AP
U024B:00 Lost Communication with Seat Control Module "G": No Sub Type Information GO to Pinpoint Test AQ
U024C:00 Lost Communication with Seat Control Module "H": No Sub Type Information GO to Pinpoint Test AR
U0256:00 Lost Communication With Front Controls Interface Module "A": No Sub Type Information GO to Pinpoint Test AT
U0415:00 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information
NOTE: If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the ABS module. Refer to: Anti-Lock Brake System (ABS) and Stability Control .
U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information
NOTE: If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the BCM. Refer to: Body Control Module (BCM) .
U0423:00 Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information
NOTE: If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: Instrumentation, Message Center and Warning Chimes .
U0452:00 Invalid Data Received From Restraints Control Module: No Sub Type Information
NOTE: If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom.
DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the RCM. Refer to: Airbag Supplemental Restraint System (SRS) .
U1018:00 Lost Communication With Generic Function Module: No Sub Type Information GO to Pinpoint Test AU
U1A00:87 Private Communication Network: Missing Message GO to Pinpoint Test T
U2017:45 Control Module Software #2: Program Memory Failure CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR .
U2017:51 Control Module Software #2: Not Programmed This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming .
U2017:52 Control Module Software #2: Not Activated This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming .
U2017:54 Control Module Software #2: Missing Calibration This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming .
U2100:00 Initial Configuration Not Complete: No Sub Type Information This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. Refer to: SYNC Module [APIM] Programming .
U3000:04 Control Module: System Internal Failure CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR . .
U3000:09 Control Module: Component Failure CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR . .
U3000:41 Control Module: General Checksum Failure CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR . .
U3000:88 Control Module: Bus Off
NOTE: The module was unable to communicate on the network at a point in time. The fault is not currently present since the module had to communicate with the diagnostic scan tool to report this DTC.
|
INSPECT for damaged or corroded wiring at the APIM. Refer to Wiring Diagrams Module Communications Network for schematic and connector information. CLEAR the DTC. WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to APIM GUIDED ROUTINE TESTING -- NAVIGATOR . .
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to Pinpoint Test AV
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to Pinpoint Test AW
scientia non olet · About LEMON Manuals