Common Specifications & Procedures
CONTINENTAL COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| Specifications | |||
| Torque | |||
| Refer to the appropriate component in Removal And Installation | |||
| Axle Nut/Hub Nut | Halfshaft Nut Torque: 98 lb.ft (133 Nm) | ||
| Battery | Specifications | ||
| Brakes | |||
| Bleeding Sequence | Brake System Pressure Bleeding | ||
| Front Disc Brakes w/Torque | For torque specifications, refer to the appropriate procedure in Removal And Installation | ||
| Rear Disk Brakes w/Torque | For torque specifications, refer to the appropriate procedure in Removal And Installation | ||
| Charging | |||
| Generator w/Torque | |||
| 2.7L EcoBoost/3.0 EcoBoost | Generator - 2.7L Ecoboost (238Kw/324Ps) 3.0L Ecoboost Torque: 35 lb.ft (47 Nm) |
||
| 3.7L DURATEC | Generator - 3.7L Duratec (227KW 301PS) Generator Stud Nut: 35 lb.ft (47 Nm) Generator Stud Bolt: 71 lb.in (8 Nm) Generator Bolt: 35 lb.ft (47 Nm) |
||
| Drive Belts | |||
| Adjustment | |||
| 2.7L EcoBoost | Accessory Drive | ||
| 3.0L EcoBoost | Accessory Drive | ||
| 3.7L DURATEC | Accessory Drive | ||
| Belt Routing | |||
| 2.7L EcoBoost | Accessory Drive - Component Location | ||
| 3.0L EcoBoost | Accessory Drive - Component Location | ||
| 3.7L DURATEC | Accessory Drive - Component Location | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 2.7L EcoBoost | Specifications | ||
| 3.0L EcoBoost | Specifications | ||
| 3.7L DURATEC | Specifications | ||
| Pressure Relief Cap | 145 kPa (21 psi) | ||
| Thermostat R & I | |||
| 2.7L EcoBoost | Thermostat | ||
| 3.0L EcoBoost | Thermostat | ||
| 3.7L DURATEC | Thermostat and Thermostat Housing | ||
| Water Pump R & I | |||
| 2.7L EcoBoost | Coolant Pump | ||
| 3.0L EcoBoost | Coolant Pump | ||
| 3.7L DURATEC | Coolant Pump | ||
| Engine Mechanical | |||
| 2.7L EcoBoost | |||
| Compression | Specifications | ||
| Reading 1: Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park | 21 psi (144.8 kPa) | ||
| Reading 2: Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park (Oil Pressure Control Solenoid connector disconnected) | Reading 1 value plus 8 psi (55.1 kPa) | ||
| Overhaul | Specifications | ||
| Torque | Refer to the appropriate component in Removal And Installation and Removal And Installation | ||
| 3.0L EcoBoost | |||
| Compression | Specifications | ||
| Reading 1: Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park | 21 psi (144.8 kPa) | ||
| Reading 2: Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park (Oil Pressure Control Solenoid connector disconnected) | Reading 1 value plus 8 psi (55.1 kPa) | ||
| Overhaul | Specifications | ||
| Torque | Refer to the appropriate component in Removal And Installation and Removal And Installation | ||
| 3.7L DURATEC | |||
| Compression | Specifications | ||
| Oil pressure @ 1, 500 rpm with engine at normal operating temperature | 30.0 psi (206.8 kPa) | ||
| Overhaul | Specifications | ||
| Torque | Refer to the appropriate component in Removal And Installation | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate Torque | |||
| 2.7L EcoBoost | Flexplate 59 lb.ft (80 Nm) |
||
| 3.0L EcoBoost |
80 Nm (59 lb-ft) |
||
| 3.7L DURATEC | Flexplate 80 Nm (59 lb-ft) |
||
| Fuel System | |||
| Fuel Filter Location | Vehicle has a lifetime fuel filter which is serviced as part of the Fuel Pump (FP) module. | ||
| Fuel Filter R & I | |||
| 2.7L EcoBoost | Fuel Pump And Sender Unit | ||
| 3.0L EcoBoost | Fuel Pump And Sender Unit | ||
| 3.7L DURATEC | Fuel Pump And Sender Unit | ||
| Pressure Release Procedure | |||
| 2.7L EcBoost | Fuel System Pressure Release | ||
| 3.0L EcoBoost | Fuel System Pressure Release | ||
| 3.7L DURATEC | Fuel System Pressure Release | ||
| Pressure Specification | |||
| 2.7L EcoBoost | Specifications | ||
| 3.0L EcoBoost | Specifications | ||
| 3.7L DURATEC | Specifications | ||
| Fuel Pressure Test Procedure | |||
| 2.7L EcoBoost | Fuel System Pressure Check | ||
| 3.0L EcoBoost | Fuel System Pressure Check | ||
| 3.7L DURATEC | Fuel System Pressure Check | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||
| Ignition Wires | Engine has coil-on-plug ignition. | ||
| Spark Plugs | |||
| 2.7L EcoBoost | |||
| Type | CYFS 12Y PT | ||
| Gap | 0.028-0.031 in (0.7-0.8 mm) | ||
| Torque | 133 lb.in (15 Nm) | ||
| 3.0L EcoBoost | |||
| Type | CYFS 12Y PT | ||
| Gap | 0.028-0.031 in (0.7-0.8 mm) | ||
| Torque | Torque: 133 lb.in (15 Nm) | ||
| 3.7L DURATEC | |||
| Type | CYFS 12F 5 | ||
| Gap | 0.051 in (1.3 mm) | ||
| Torque | 133 lb.in (15 Nm) | ||
| Starting | |||
| Starter w/Torque | |||
| 2.7L EcoBoost | 2 Stud Bolts: 35 lb.ft (48 Nm) | ||
| 3.0L EcoBoost | 2 Stud Bolts: 35 lb.ft (48 Nm) | ||
| 3.7L DURATEC | 2 Stud Bolts: 35 lb.ft (48 Nm) | ||
| Wheel Alignment | |||
| Adjustment Specifications | Specifications | ||
| Torque | Refer to the appropriate component in General Procedures | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | For tightening sequence, refer to Wheel And Tire
. Torque: 162 lb.ft (220 Nm) |
||