Pinpoint Test K : The FCIM (Front Controls Interface Module) Does Not Respond To The Diagnostic Scan Tool

WARNING: This page is about a different car, the 2018 Ford F-550 Super Duty, 2018 Ford F-450 Super Duty, 2018 Ford F-350 Super Duty, and 2018 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

K1 CHECK THE MS-CAN (MEDIUM SPEED-CONTROLLER AREA NETWORK) TERMINATION RESISTANCE

Ignition OFF.

Disconnect negative battery cable.

Disconnect the diagnostic scan tool cable from the DLC.

Disconnect GWM C2431

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2431-23	Courtesy of FORD MOTOR COMPANY	C2431-22

Is the resistance between 108 and 132 ohms?

Yes

GO to K3

GO to K2

K2 CHECK THE MS-CAN (MEDIUM SPEED-CONTROLLER AREA NETWORK) CIRCUITS BETWEEN THE FCIM (FRONT CONTROLS INTERFACE MODULE) AND THE GWM (GATEWAY MODULE A) FOR AN OPEN

Disconnect: FCIM C2402A .

Measure:

With multi-function display

Positive Lead	Measurement / Action	Negative Lead
C2402A-17	Courtesy of FORD MOTOR COMPANY	C2431-23
C2402A-18	Courtesy of FORD MOTOR COMPANY	C2431-22

Without multi-function display

Positive Lead	Measurement / Action	Negative Lead
C2402A-1	Courtesy of FORD MOTOR COMPANY	C2431-23
C2402A-2	Courtesy of FORD MOTOR COMPANY	C2431-22

Are the resistances less than 3 ohms?

Yes

GO to K5

No	REPAIR the circuit in question.

K3 CHECK THE FCIM (FRONT CONTROLS INTERFACE MODULE) VOLTAGE SUPPLY CIRCUIT FOR AN OPEN

Connect negative battery cable.

Ignition ON.

Measure:

With multi-function display

Positive Lead	Measurement / Action	Negative Lead
C2402A-26	Courtesy of FORD MOTOR COMPANY	Ground

Without multi-function display

Positive Lead	Measurement / Action	Negative Lead
C2402A-14	Courtesy of FORD MOTOR COMPANY	Ground

Is the voltage greater than 11 volts?

Yes

GO to K4

No	VERIFY BCM fuse 12 (7.5A) is OK. If OK, REPAIR the circuit. If not OK, REFER to the OEM Wiring Diagrams to identify the possible causes of the circuit short.

K4 CHECK THE FCIM (FRONT CONTROLS INTERFACE MODULE) GROUND CIRCUIT FOR AN OPEN

Ignition OFF.

Disconnect negative battery cable.

Measure:

With multi-function display

Positive Lead	Measurement / Action	Negative Lead
C2402A-1	Courtesy of FORD MOTOR COMPANY	Ground

Without multi-function display

Positive Lead	Measurement / Action	Negative Lead
C2402A-26	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance less than 3 ohms?

Yes	CONNECT negative battery cable. GO to K5

No	REPAIR the circuit.

K5 CHECK FOR CORRECT FCIM (FRONT CONTROLS INTERFACE MODULE) OPERATION

Ignition OFF.

Disconnect and inspect all the FCIM connectors and related in-line connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the FCIM connectors and related in-line connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to FCIM HARDWARE TESTING .

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.