Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2020 Lincoln Aviator. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| BCM | B11D9:16 | Vehicle Battery:Circuit Voltage Below Threshold | GO to Pinpoint Test Y |
| BCM | B11D9:17 | Vehicle Battery:Circuit Voltage Above Threshold | GO to Pinpoint Test Z |
| BCM | U0100:87 | Lost Communication With ECM/PCM "A":Missing Message | GO to Pinpoint Test A |
| BCM | U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module:Missing Message | GO to Pinpoint Test B |
| BCM | U0131:87 | Lost Communication With Power Steering Control Module:Missing Message | GO to Pinpoint Test C |
| BCM | U0151:87 | Lost Communication With Restraints Control Module:Missing Message | GO to Pinpoint Test D |
| BCM | U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module:Missing Message | GO to Pinpoint Test E |
| BCM | U0166:87 | Lost Communication With Auxiliary Heater Control Module:Missing Message | GO to Pinpoint Test F |
| BCM | U0184:87 | Lost Communication With Radio:Missing Message | GO to Pinpoint Test G |
| BCM | U0198:87 | Lost Communication With Telematic Control Module: Missing Message | GO to Pinpoint Test H |
| BCM | U0199:87 | Lost Communication With "Door Control Module A":Missing Message | GO to Pinpoint Test I |
| BCM | U019B:87 | Lost Communication With Battery Charger Control Module:Missing Message | GO to Pinpoint Test J |
| BCM | U0200:87 | Lost Communication With "Door Control Module B":Missing Message | GO to Pinpoint Test K |
| BCM | U0208:87 | Lost Communication With "Seat Control Module A":Missing Message | GO to Pinpoint Test L |
| BCM | U0212:87 | Lost Communication With Steering Column Control Module:Missing Message | GO to Pinpoint Test M |
| BCM | U0230:87 | Lost Communication With Rear Gate Module:Missing Message | GO to Pinpoint Test N |
| BCM | U0232:87 | Lost Communication With Side Obstacle Detection Control Module "A":Missing Message | GO to Pinpoint Test O |
| BCM | U0233:87 | Lost Communication With Side Obstacle Detection Control Module "B":Missing Message | GO to Pinpoint Test P |
| BCM | U023A:87 | Lost Communication With Image Processing Control Module A:Missing Message | GO to Pinpoint Test Q |
| BCM | U0252:87 | Lost Communication With Lighting Control Module-Rear "B":Missing Message | GO to Pinpoint Test R |
| BCM | U0253:87 | Lost Communication With Accessory Protocol Interface Module:Missing Message | GO to Pinpoint Test S |
| BCM | U0256:87 | Lost Communication With Front Controls Interface Module "A":Missing Message | GO to Pinpoint Test T |
| BCM | U0293:87 | Lost Communication With Hybrid/EV Powertrain Control Module "A":Missing Message | GO to Pinpoint Test U |
| BCM | U1000:00 | Solid State Driver Protection Active:Driver Disabled: No Sub Type Information | GO to Pinpoint Test V |
| BCM | U2005:85 | Vehicle Speed:Signal Above Allowable Range | GO to Pinpoint Test W |
| BCM | U2100:00 | Initial Configuration Not Complete:No Sub Type Information | GO to Pinpoint Test X |
| BCM | U2101:00 | Control Module Configuration Inomplete:No Sub Type Information | GO to Pinpoint Test X |
| BCM | U2200:00 | Control Module Configuration Memory Corrupt:No Sub Type Information | GO to Pinpoint Test X |
| BCM | U3000:49 | Control Module:Internal Electronic Failure | GO to Pinpoint Test AA |
| BCM | U3006:16 | Control Module Input Power "A":Circuit Voltage Below Threshold | GO to Pinpoint Test Y |
| BCM | U3006:17 | Control Module Input Power "A":Circuit Voltage Above Threshold | GO to Pinpoint Test Z |
| BCM | U3006:1C | Control Module Input Power "A":Circuit Voltage Out of Range | GO to Pinpoint Test Y |
| BCM | U3006:1C | Control Module Input Power "A":Circuit Voltage Out of Range | GO to Pinpoint Test Z |
| BCM | U3007:16 | Control Module Input Power "B":Circuit Voltage Below Threshold | GO to Pinpoint Test Y |
| BCM | U3007:17 | Control Module Input Power "B":Circuit Voltage Above Threshold | GO to Pinpoint Test Z |
| BCM | U3013:16 | Control Module Input Power "C":Circuit Voltage Below Threshold | GO to Pinpoint Test Y |
| BCM | U3013:17 | Control Module Input Power "C":Circuit Voltage Above Threshold | GO to Pinpoint Test Z |
| BCM | U3014:16 | Control Module Input Power "D":Circuit Voltage Below Threshold | GO to Pinpoint Test Y |
| BCM | U3014:17 | Control Module Input Power "D":Circuit Voltage Above Threshold | GO to Pinpoint Test Z |