| SECM |
C100B:62 |
Motor Drive Current: Signal Compare Failure |
GO to Pinpoint Test I |
| SECM |
C100C:27 |
Steering Tracking: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test J |
| SECM |
C100C:29 |
Steering Tracking: Signal Invalid |
GO to Pinpoint Test AD |
| SECM |
C100C:63 |
Steering Tracking: Circuit/Component Protection Time-Out |
GO to Pinpoint Test I |
| SECM |
C100C:67 |
Steering Tracking: Signal Incorrect After Event |
GO to Pinpoint Test AD |
| SECM |
C100C:68 |
Steering Tracking: Event Information |
GO to Pinpoint Test AD |
| SECM |
C100C:9A |
Steering Tracking: Component or System Operating Conditions |
GO to Pinpoint Test AD |
| SECM |
C1039:75 |
Active Front Steering (AFS) Lock: Emergency Position Not Reachable |
GO to Pinpoint Test J |
| SECM |
C1039:7F |
Active Front Steering (AFS) Lock: Actuator Stuck Off |
GO to Pinpoint Test K |
| SECM |
C1039:92 |
Active Front Steering (AFS) Lock: Performance or Incorrect Operation |
GO to Pinpoint Test K |
| SECM |
C1039:94 |
Active Front Steering (AFS) Lock: Unexpected Operation |
GO to Pinpoint Test K |
| SECM |
C1B00:81 |
Steering Angle Sensor: Invalid Serial Data Received |
GO to Pinpoint Test AE |
| SECM |
C1B00:82 |
Steering Angle Sensor: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test AE |
| SECM |
C1B00:83 |
Steering Angle Sensor: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AE |
| SECM |
C1B00:87 |
Steering Angle Sensor: Missing Message |
GO to Pinpoint Test AE |
| SECM |
C200D:28 |
Motor Rotation Angle Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure |
GO to Pinpoint Test K |
| SECM |
C200D:62 |
Motor Rotation Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test K |
| SECM |
U0001:88 |
High Speed CAN Communication Bus: Bus Off |
GO to Pinpoint Test AF |
| SECM |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test C |
| SECM |
U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test D |
| SECM |
U0126:00 |
Lost Communication With Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test E |
| SECM |
U0131:00 |
Lost Communication With Power Steering Control Module 'A': No Sub Type Information |
GO to Pinpoint Test F |
| SECM |
U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test G |
| SECM |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test H |
| SECM |
U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| SECM |
U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test C |
| SECM |
U0401:81 |
Invalid Data Received from ECM/PCM A: Invalid Serial Data Received |
GO to Pinpoint Test C |
| SECM |
U0401:82 |
Invalid Data Received from ECM/PCM A: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test C |
| SECM |
U0401:83 |
Invalid Data Received from ECM/PCM A: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test C |
| SECM |
U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test D |
| SECM |
U0415:81 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': Invalid Serial Data Received |
GO to Pinpoint Test D |
| SECM |
U0415:82 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test D |
| SECM |
U0415:83 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test D |
| SECM |
U0420:00 |
Invalid Data Received from Power Steering Control Module 'A': No Sub Type Information |
GO to Pinpoint Test F |
| SECM |
U0428:00 |
Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test E |
| SECM |
U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test H |
| SECM |
U0557:00 |
Invalid Data Received From Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test AG |
| SECM |
U2000:68 |
Motor Temperature: Event Information |
GO to Pinpoint Test M |
| SECM |
U2000:98 |
Motor Temperature: Component Or System Over Temperature |
GO to Pinpoint Test M |
| SECM |
U2001:02 |
Reduced System Function: General Signal Failure |
GO to Pinpoint Test P |
| SECM |
U2001:53 |
Reduced System Function: Deactivated |
GO to Pinpoint Test J |
| SECM |
U2001:68 |
Reduced System Function: Event Information |
GO to Pinpoint Test Q |
| SECM |
U2001:92 |
Reduced System Function: Performance or Incorrect Operation |
GO to Pinpoint Test K |
| SECM |
U2001:98 |
Reduced System Function: Component Or System Over Temperature |
GO to Pinpoint Test R |
| SECM |
U2002:68 |
Switch: Event Information |
GO to Pinpoint Test S |
| SECM |
U2002:98 |
Switch: Component Or System Over Temperature |
GO to Pinpoint Test S |
| SECM |
U2002:9F |
Switch: Stuck Off |
GO to Pinpoint Test T |
| SECM |
U2011:00 |
Motor: No Sub Type Information |
GO to Pinpoint Test U |
| SECM |
U2016:47 |
Control Module Main Software: Watchdog / Safety μC Failure |
GO to Pinpoint Test J |
| SECM |
U201A:53 |
Control Module Main Calibration Data: Deactivated |
GO to Pinpoint Test J |
| SECM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test N |
| SECM |
U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test N |
| SECM |
U210A:02 |
Temperature Sensor: General Signal Failure |
GO to Pinpoint Test J |
| SECM |
U3000:18 |
Control Module: Circuit Current Below Threshold |
GO to Pinpoint Test J |
| SECM |
U3000:19 |
Control Module: Circuit Current Above Threshold |
GO to Pinpoint Test L |
| SECM |
U3000:45 |
Control Module: Program Memory Failure |
GO to Pinpoint Test J |
| SECM |
U3000:46 |
Control Module: Calibration / Parameter Memory Failure |
GO to Pinpoint Test K |
| SECM |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test K |
| SECM |
U3000:54 |
Control Module: Missing Calibration |
GO to Pinpoint Test J |
| SECM |
U3000:61 |
Control Module: Signal Calculation Failure |
GO to Pinpoint Test K |
| SECM |
U3000:68 |
Control Module: Event Information |
GO to Pinpoint Test I |
| SECM |
U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test J |
| SECM |
U3000:98 |
Control Module: Component Or System Over Temperature |
GO to Pinpoint Test I |
| SECM |
U3000:9A |
Control Module: Component or System Operating Conditions |
GO to Pinpoint Test K |
| SECM |
U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| SECM |
U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test B |
| SECM |
U3003:1C |
Battery Voltage: Circuit Voltage Out Of Range |
GO to Pinpoint Test A |
| SECM |
U3003:68 |
Battery Voltage: Event Information |
GO to Pinpoint Test A |