| ABS |
C0051:23 |
Steering Wheel Position Sensor: Signal Stuck Low |
GO to Pinpoint Test U |
| ABS |
C0051:23 |
Steering Wheel Position Sensor: Signal Stuck Low |
GO to Pinpoint Test V |
| ABS |
C0051:27 |
Steering Wheel Position Sensor: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test U |
| ABS |
C0051:27 |
Steering Wheel Position Sensor: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test V |
| ABS |
C0051:28 |
Steering Wheel Position Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test U |
| ABS |
C0051:28 |
Steering Wheel Position Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test V |
| ABS |
C0051:29 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test U |
| ABS |
C0051:29 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test V |
| ABS |
C0051:54 |
Steering Wheel Position Sensor: Missing Calibration |
GO to Pinpoint Test U |
| ABS |
C0051:54 |
Steering Wheel Position Sensor: Missing Calibration |
GO to Pinpoint Test V |
| ABS |
C0051:62 |
Steering Wheel Position Sensor: Signal Compare Failure |
GO to Pinpoint Test U |
| ABS |
C0051:62 |
Steering Wheel Position Sensor: Signal Compare Failure |
GO to Pinpoint Test V |
| ABS |
C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test U |
| ABS |
C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test V |
| ABS |
C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test U |
| ABS |
C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test V |
| ABS |
C0051:82 |
Steering Wheel Position Sensor: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test U |
| ABS |
C0051:82 |
Steering Wheel Position Sensor: Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test V |
| ABS |
C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test U |
| ABS |
C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test V |
| ABS |
C0051:86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test U |
| ABS |
C0051:86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test V |
| ABS |
C0051:96 |
Steering Wheel Position Sensor: Component Internal Failure |
GO to Pinpoint Test U |
| ABS |
C0051:96 |
Steering Wheel Position Sensor: Component Internal Failure |
GO to Pinpoint Test V |
| ABS |
C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test U |
| ABS |
C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test V |
| PSCM |
B1304:68 |
Electronic Power Assisted Steering System: Event Information |
GO to Pinpoint Test AY |
| PSCM |
B1D23:4B |
Overheat Sensor: Over Temperature |
GO to Pinpoint Test AN |
| PSCM |
C102D:00 |
High Friction Inside Power Steering: No Sub Type Information |
GO to Pinpoint Test W |
| PSCM |
C1110:56 |
Power steering Calibration Data: Invalid/Incompatible Configuration |
GO to Pinpoint Test Q |
| PSCM |
C1B00:00 |
Steering Angle Sensor: No Sub Type Information |
GO to Pinpoint Test AQ |
| PSCM |
C1B00:2F |
Steering Angle Sensor: Signal Erratic |
GO to Pinpoint Test AQ |
| PSCM |
C1B00:49 |
Steering Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test AQ |
| PSCM |
C1B00:62 |
Steering Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test AQ |
| PSCM |
C200B:49 |
Steering Shaft Torque Sensor 1: Internal Electronic Failure |
GO to Pinpoint Test AR |
| PSCM |
C200B:62 |
Steering Shaft Torque Sensor 1: Signal Compare Failure |
GO to Pinpoint Test AR |
| PSCM |
C200C:49 |
Steering Shaft Torque Sensor 2: Internal Electronic Failure |
GO to Pinpoint Test AS |
| PSCM |
C200D:49 |
Motor Rotation Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test AT |
| PSCM |
C200D:62 |
Motor Rotation Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test AT |
| PSCM |
U0001:88 |
High Speed CAN Communication Bus: Bus Off |
GO to Pinpoint Test A |
| PSCM |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test X |
| PSCM |
U0102:00 |
Lost Communication with Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test BF |
| PSCM |
U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test Y |
| PSCM |
U0122:00 |
Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test BG |
| PSCM |
U0126:00 |
Lost Communication With Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test AK |
| PSCM |
U0137:00 |
Lost Communication With Trailer Brake Control Module: No Sub Type Information |
GO to Pinpoint Test BH |
| PSCM |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test Z |
| PSCM |
U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test AA |
| PSCM |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| PSCM |
U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AC |
| PSCM |
U0159:00 |
Lost Communication With Parking Assist Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AD |
| PSCM |
U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test AE |
| PSCM |
U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AF |
| PSCM |
U023B:00 |
Lost Communication With Image Processing Module B: No Sub Type Information |
GO to Pinpoint Test AF |
| PSCM |
U0252:00 |
Lost Communication With Lighting Control Module- Rear 'B': No Sub Type Information |
GO to Pinpoint Test AL |
| PSCM |
U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test AM |
| PSCM |
U0256:00 |
Lost Communication With Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test BI |
| PSCM |
U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AG |
| PSCM |
U0403:00 |
Invalid Data Received From Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test BF |
| PSCM |
U0403:29 |
Invalid Data Received From Transfer Case Control Module: Signal Invalid |
GO to Pinpoint Test BF |
| PSCM |
U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AH |
| PSCM |
U0415:22 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': Signal Amplitude Greater Than Maximum |
GO to Pinpoint Test AH |
| PSCM |
U0415:29 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': Signal Invalid |
GO to Pinpoint Test AH |
| PSCM |
U0415:81 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': Invalid Serial Data Received |
GO to Pinpoint Test AH |
| PSCM |
U0416:00 |
Invalid Data Received From Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test BD |
| PSCM |
U0416:08 |
Invalid Data Received From Vehicle Dynamics Control Module: Bus Signal / Message Failure |
GO to Pinpoint Test BD |
| PSCM |
U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test BA |
| PSCM |
U0422:29 |
Invalid Data Received From Body Control Module: Signal Invalid |
GO to Pinpoint Test BA |
| PSCM |
U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test AC |
| PSCM |
U0423:29 |
Invalid Data Received from Instrument Panel Cluster Control Module: Signal Invalid |
GO to Pinpoint Test AC |
| PSCM |
U0428:00 |
Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test BB |
| PSCM |
U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BC |
| PSCM |
U045A:00 |
Invalid Data Received From Parking Assist Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AI |
| PSCM |
U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AJ |
| PSCM |
U053C:00 |
Invalid Data Received From Image Processing Module B: No Sub Type Information |
GO to Pinpoint Test AJ |
| PSCM |
U0553:00 |
Invalid Data Received From Lighting Control Module-Rear 'B': No Sub Type Information |
GO to Pinpoint Test AL |
| PSCM |
U0554:00 |
Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test BE |
| PSCM |
U0557:00 |
Invalid Data Received From Front Controls Interface Module 'A': No Sub Type Information |
GO to Pinpoint Test BJ |
| PSCM |
U2011:61 |
Motor: Signal Calculation Failure |
GO to Pinpoint Test AU |
| PSCM |
U2016:47 |
Control Module Main Software: Watchdog/Safety μC Failure |
GO to Pinpoint Test AX |
| PSCM |
U2016:48 |
Control Module Main Software: Supervision Software Failure |
GO to Pinpoint Test AX |
| PSCM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AZ |
| PSCM |
U2100:55 |
Initial Configuration Not Complete: Not Configured |
GO to Pinpoint Test AZ |
| PSCM |
U2300:55 |
Central Configuration: Not Configured |
GO to Pinpoint Test R |
| PSCM |
U2300:56 |
Central Configuration: Invalid/Incompatible Configuration |
GO to Pinpoint Test R |
| PSCM |
U3000:41 |
Control Module: General Checksum Failure |
GO to Pinpoint Test AW |
| PSCM |
U3000:42 |
Control Module: General Memory Failure |
GO to Pinpoint Test AW |
| PSCM |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AW |
| PSCM |
U3000:61 |
Control Module: Signal Calculation Failure |
GO to Pinpoint Test AW |
| PSCM |
U3000:62 |
Control Module: Signal Compare Failure |
GO to Pinpoint Test AW |
| PSCM |
U3000:64 |
Control Module: Signal Plausibility Failure |
GO to Pinpoint Test AW |
| PSCM |
U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test B |
| PSCM |
U3001:68 |
Control Module Improper Shutdown Performance: Event Information |
GO to Pinpoint Test AP |
| PSCM |
U3001:89 |
Control Module Improper Shutdown Performance: Data Transfer Failure |
GO to Pinpoint Test AP |
| PSCM |
U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test AO |
| PSCM |
U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test AO |
| PSCM |
U3003:18 |
Battery Voltage: Circuit Current Below Threshold |
GO to Pinpoint Test AO |
| PSCM |
U3003:19 |
Battery Voltage: Circuit Current Above Threshold |
GO to Pinpoint Test AO |
| PSCM |
U3003:68 |
Battery Voltage: Event Information |
GO to Pinpoint Test AO |
| PSCM |
U3003:A2 |
Battery Voltage: System Voltage Low |
GO to Pinpoint Test AO |
| PSCM |
U3008:1B |
Control Module Ground 'A': Circuit Resistance Above Threshold |
GO to Pinpoint Test BK |
| PSCM |
U3009:1B |
Control Module Ground 'B': Circuit Resistance Above Threshold |
GO to Pinpoint Test BK |